Samsung Refrigerator RF220DCTAS8 Parts

• Door won't close
• Shuts off too soon
• Doesn't shut off
• Takes too long to dry

When I looked up the part number there was a handy video that popped up. I watched the video and thought "how easy!" so, I ordered that part and waited. The next day, I thought I better start to take the door off of my dryer (because that's what the video instructed, and I wanted a head start) so as I was going into the garage to get my tools, my son came in with a small package. It was the part. That came, to quote another customer, "Crazy Fast!" All the way from Kentucky to California! ... Read more

• No heat or not enough heat
• Too hot

Since the dryer was 24 years old I opted to replace all the possible problem components, instead of just the bad one. The parts aren't that expensive and do to their age I figured it was worth it to avoid having to go back into the dryer in a few months. The repair was surprisingly easy and went pretty much as the video instruction AppliancePartPros provided with one exception. Because, my model was much older than that used in the video, I had a more difficult time replacing the Heating... Read more

Poped off plastics caseing inside the frigerator. Unscrewed 4 screws holding black fan inplace. Followed yellow wire to locate white sensor. Need to be careful not to break styrofoam, don't force it, it should seporate from plastic easy as long as the 4 screws are out. Swap it for the new one and button it back up. While I was in there I replaced the defrost sensor and the other sensor next to the heating rod. Also I know there is an issue with drain hole plugging up with ice so I extended the... Read more

I ordered a new one. Got it much sooner than expected. Read more

Repair went great thanks for your service Read more

I loosened middle hinge by the 2 screws which holds a power cord that clips together, then slid the hinge flap upward to release from the door. My bottom clip hinge was broken away from spring and the only way to attach a new hinge clip was to carefully separate the hinge flap. This can be done by squeezing the flap to see where the separation seams are. Small narrow screwdrivers along with a spatula will do without damaging the plastic. This allowed for acess to the spring which connects to a... Read more

The amount of water being dispensed into the ice cube tray was excessive, causing overflow of the tray. The water then ran into the collection bin and even down the side walls of the freezer creating a huge block of ice in the bin, and ice all over the lower shelves as well. The excessive build up of ice caused the cube tray to crack and also split the little silicone water grommet that connects to the water delivery tube which directs water into the cube tray. Look out for that little tube... Read more

• Noisy
• Freezer section too warm
• Fridge too warm

Replace evaporator fan motor located in freezer compartment Read more

Replaced broken handle support bracket (part #AP5620448) and cap (part #AP5620751). Used a phillips head screwdriver and allen wrench. Pliers also came in very handy. If replacing cap and support bracket, be sure to install cap before support bracket, otherwise you'll have trouble installing the cap. I ended up not needing to replace the fixer handle (part #AP4372038), but I'll keep it around just in case. Read more

Samsung refrrigerator. it started when the setting was on cubes but was putting out crushed ice. then months later the water refill was running down into the ice bucket causing a massive block of ice in the bucket. look closely at the first two or three cubes in the ice tray after they unload. mine were not dumping and staying in the tray. when the water refill kicked on it would overfill the tray (because of the leftover cubes remaining in the tray) and would run down into the ice bucket... Read more

• Little to no heat when broiling
• Element will not heat
• Little to no heat when baking

I ordered the bake unit from appliancepartspro.com; while ordering, I decided to go ahead and replace the oven broiler burner as well. Appliancepartspros.com's videos helped me replace the parts with ease. It took barely 30 minutes to install both. Plus, very fast shipping and correct parts. Now, I do not have to worry about baking during Thanksgiving! Cheers, Sean Read more

Turn off the water to the ice maker. Unload the freezer and remove the freezer door so you have room to work. Remove the ice maker by removing 2 screws in the front then pull the unit toward the front and unplug the wiring connection. The pipe will now be exposed. Remove the flexible piece from the front of the pipe that directs the water flow to the ice cube tray. Remove the wire tie on the front of the pipe and peel off the insulation surrounding the pipe. The heater will now be exposed.... Read more

I have a large Samsung 4 door refrigerator. One of the rear wheels broke. To replace it, you need the wheel and the shaft. To lift the refrigerator for the repair, I had my wife stand in front of it with her foot on a board that was wedged against the front wheels. I then pushed the refrigerator up from behind and slid a 3/4" piece of plywood underneath the bottom with my foot. This gives you enough space to do the repair. After removing the back cover, it's best just to knock out the broken... Read more

Samsung refrrigerator. it started when the setting was on cubes but was putting out crushed ice. then months later the water refill was running down into the ice bucket causing a massive block of ice in the bucket. look closely at the first two or three cubes in the ice tray after they unload. mine were not dumping and staying in the tray. when the water refill kicked on it would overfill the tray (because of the leftover cubes remaining in the tray) and would run down into the ice bucket... Read more

I did an internet search on the refrigerator model and part name "replacement shelf". I checked four or five different vendors to ensure that I understood which part I needed and whether there were any options. Once I verified my part requirement, I ranked the suppliers by cost low to high and then I checked vendor ratings. AppliancePartsPros was within a couple bucks of the lowest cost vendor, but had a much better rating. Read more

I removed the door and the hinge assembly from the right side; it turns out the grommet had never been installed and this is what was causing the door to grind down the metal hinge. It was remarkably easy to replace and my door is working perfectly! Read more