Poulan Carburetor

This is a replacement carburetor for Husqvarna string trimmers and is also used on some Craftsman models. It consists of an aluminum body with a bright blue choke and cherry red primer bulb. Engines rely on a mixture of fuel and air for proper operation. In a small engine, the fuel and air mix inside the carburetor. This is achieved with a series of small channels, which release a fine mist of fuel into a vortex of air. When one of these channels gets clogged, it can negatively impact engine performance. Carburetors can often be cleaned with a commercial carburetor cleaning spray, but this is sometimes not sufficient to clean a badly clogged carburetor. In this case, other measures such as hypersonic cleaners can often be effective, but they’re not always worth the cost. The alternative is replacing the entire carburetor, which can be done using this kit. This is an OEM part sourced directly from the manufacturer, and it is sold individually. A heat shield is also included with the kit.

The chainsaw carburetor mixes air and gas before this mixture makes its way to the engine. If this is not working correctly, the engine receives a less efficient gas supply or no gas supply at all. If your chainsaw has a full tank of gas but will not start or stops just after starting, the carburetor may need to be replaced. While carburetors can be cleaned to get them working again, they often need to be replaced if they have become too clogged. Depending on what you can reuse from your old carburetor, you may need to order new gaskets as well to ensure an airtight seal. A screwdriver, a nut driver, and a socket wrench set may be needed to complete this repair. This chainsaw carburetor is sold individually from other parts, but it does include the primer bulb. It is compatible with Craftsman and Poulan chainsaws. This chainsaw carburetor is a genuine OEM part.

Known as the primer bulb, this replacement part makes it easy for the engine to start. Responsible for circulating fuel through the carburetor, the purge bulb removes air out of the lines and allows the carb to have a new fuel charge before a start. The bulb may harden and crack over time, so it needs to be replaced to prevent an air leak. This is a genuine OEM part that works on different models of gas chainsaws from AYP, Craftsman, Poulan, and Husqvarna. This component is sold individually and comes with two screws.

Trimmers are found in many shapes and sizes, but they all do the same tough job. That is why so many use gas-powered engines that rely on a carburetor to send a proper blend of air and fuel into the cylinder. If an engine starts and dies, or fails to start even with a fresh tank of fuel, it is likely that a carburetor replacement is needed. This replacement carburetor assembly provides a full carburetor replacement on a more than 40 different hand-held trimmer models made by Craftsman or Husqvarna. This is an OEM replacement part that uses durable metal for the body and ships individually. It requires an Allen wrench, pliers and a screwdriver to do the installation.

This high quality choke lever is used on string trimmers and edgers from multiple manufacturers. The plastic choke lever actuates the choke valve which creates a limit to the amount of air that can enter the engine when the equipment is cold started. If the choke lever has been damaged or is broken, it may create problems with starting the tool. If this is the case, the choke lever will need to be replaced.This is a simple replacement project that requires only a screwdriver and a pair of work gloves. Before starting, make sure the tool is turned off and the spark plug wire has been removed. Place the tool on a flat surface and take out the choke lever. The broken choke lever can be removed using the screwdriver. The new replacement choke lever can be installed before tightening the screws and using the equipment again.This is a genuine OEM replacement part that is sourced directly from the manufacturer. It is sold as an individual part. The choke lever is made for use with edgers and string trimmers manufactured by Craftsman, Husqvarna, and Poulan.

The carburetor kit has a metal body that is designed to withstand high temperatures, a rubber primer bulb, and a plastic throttle lever. The carburetor is an integral part of engines in lawn and garden equipment. This is where the air and fuel will be mixed before being sent into the engine. The air comes in through the intake tube, and it flows into a smaller tube, where the fuel is injected through small holes in the carburetor body. Then, the two are mixed and released into the engine through a butterfly valve, which controls the amount of fuel going to the engine for optimal performance. The carburetor can become clogged over time or even be broken or damaged. If the engine is not running properly, the carburetor may need to be replaced. This is a simple replacement that only requires a screwdriver. Make sure to always disconnect the spark plug and wear gloves when performing engine repairs. This kit can be used with several models of lawn and garden equipment, including brands like Weed Eater, Paramount, Poulan, Jonsered, and Husqvarna.

This certified OEM replacement part is a carburetor kit for a gas-powered leaf blower engine. For gas to ignite in an engine, there has to be the right amount of air in the system. Without oxygen, the spark won't light and the gasoline will not ignite. A carburetor is responsible for maintaining the right balance of air and gasoline. Therefore, without a properly functioning carburetor, the engine will also not function properly. Carburetors begin to break down over time because of built up exhaust and gunk in the engine. As this grime builds up, the carburetor cannot get enough air and the balance is thrown off. While carburetors can sometimes be cleaned, if it has become overly clogged or damaged, it will need to be replaced. Signs of a faulty carburetor include shakiness and black smoke, backfiring, hard starts, or an engine that will not start at all. Replacing a leaf blower's carburetor requires the crankcase line, primer line, fuel line, air filter, and throttle linkage to all be disconnected using pliers and a screwdriver. This part is intended for Craftsman, Poulan, Weed Eater, and Husqvarna leaf blowers and is sourced from the original manufacturer. It ships individually.

The carburetor is responsible for mixing the air and fuel before it enters the engine. It consists of intake and outflow valves, as well as a float and needle to monitor and manage the flow of fuel and air coming into and leaving the carburetor body. The fuel mixes with oil in the smallest part of the body and is then pushed through a butterfly valve into the engine. Adjusting the valve will adjust how much of the fuel mixture gets into the engine. In the event that an engine is not running or keeps stalling, the carburetor may need of repair or replacement. This kit is designed to assist with the repair or refurbishment of several carburetors in various chainsaws. It is a full carburetor, not a rebuild kit. Installation will require a screwdriver to replace the carburetor. This OEM carburetor assembly kit is compatible with a number of chainsaws from Husqvarna. The kite includes the carburetor body, along with the float, needle, gaskets, and seals that are all made to manufacturer standards, offering an exact fit for compatible models.

This part is a replacement carburetor assembly. This is a genuine OEM part made by Husqvarna and has been sourced directly from the manufacturer. This part's intended use is to replace a broken or defective carburetor in leaf blowers.Carburetors are critical for the proper functioning of an internal combustion engine as they enable the proper mixture of air and fuel for ignition. If the carburetor is faulty, the equipment may not run properly or may not turn on at all. Thus, the carburetor will need to be replaced. When working on or near an engine it's important to make sure the equipment is powered off and completely cooled down before starting any repairs. For more accurate information on how and where to install this carburetor assembly, reference the appropriate owner's manual and specific equipment diagrams.This is an authentic OEM replacement part made of high-quality materials. This carburetor assembly can be used with different models of leaf blowers that have been manufactured by Husqvarna, Poulan, and other brands. Part sold individually.

Blowers are often designed with gas-powered engines. When a blower has adequate fuel, but the engine does not start, it could be a problem with the carburetor. This is the part that mixes air and fuel to send into the engine. If an engine starts and dies or fails to start at all, the carburetor may need replacement. This replacement for a blower carburetor works with Craftsman and Poulan blowers, and is compatible with a long list of models. This is an OEM replacement part that features a metal body and which incorporates the rubber primer bulb necessary to begin the starting process. It ships individually and is will require pliers and a screwdriver to make the repair.

This replacement part is a carburetor assembly and is intended for use in different types of lawn equipment. This is a genuine replacement part made by Husqvarna. This carburetor assembly is used in leaf blowers and snow blowers and is part of the engine. This part is one of the most important parts of the machine and is responsible for allowing it to run smoothly.A new carburetor assembly might be needed if the current engine is slow to start, slow to stop, or won't start at all. This can be due to a malfunctioning carburetor and create problems within the machine. Be sure the appliance is completely powered down before replacing this part. work gloves are recommended to ensure safety during any type of repair.This carburetor is sold individually and is a genuine OEM replacement part. This is also sourced directly from the manufacturer.

The carburetor works by mixing clean oxygen with gasoline to create a combustible mixture of fuel that the engine can burn. Without this fuel, the engine cannot run efficiently or may not start at all. If the chainsaw engine won’t start or is running roughly, check the air filter first. If issues persist, the carburetor may be the culprit. Sometimes carburetors can be cleaned and rebuilt. Other times they will need a full replacement with a genuine OEM carburetor kit like this one. This kit includes the carburetor, grommet, and air filter housing. The carburetor kit fits several models of Poulan chainsaws. This carburetor kit is a genuine OEM product directly from the manufacturer and is sold individually.

This throttle linkage is a genuine Husqvarna part, sold individually. This throttle linkage can be used as a replacement part in a leaf blower. The purpose of the throttle linkage in a leaf blower is to affix the throttle control to the carburetor so that the carburetor and throttle can work in unison to provide power to the engine and control the speed of the appliance as it is propelled forward across a variety of surfaces.The throttle linkage in a leaf blower might need to be replaced if the throttle linkage has permanently detached from its stable position within the throttle controls of the appliance or if the throttle linkage has suffered irreparable damage. If the throttle linkage is not serving its function and cannot be repaired, the throttle linkage should be removed and replaced by this genuine OEM replacement part.Sourced directly from the manufacturer, this component is a genuine replacement part that is sold individually. This throttle linkage is compatible with the following outdoor appliance brands: Husqvarna, Craftsman, Weed Eater, Poulan, and Poulan Pro.

This authentic OEM replacement carburetor assembly is a part for a gas-powered trimmer. The carburetor is an essential part of a small or medium sized gas-powered engine and is usually one of the first steps in an engine's mechanics. The carburetor receives fuel from the fuel line and mixes it with air to create a balanced mixture that is ready for combustion. This mixture has to be just right or the engine will not run properly. After a full season of use, a carburetor will usually need cleaning because they slowly build up gunk. If left uncleaned, it will degrade and may no longer allow enough fuel to pass into the engine. Should this happen, the engine will not produce enough power or may not start at all. Look for signs such as backfiring, hard starts, vibrations, or an engine that dies shortly after startup. Use a wrench set to access the carburetor, which is located behind the air filter housing. This replacement carburetor assembly is a quality part for Craftsman and Husqvarna trimmers. It comes sourced from the original manufacturer and includes a carburetor and fuel bulb.

The carburetor is the part of the chainsaw that mixes air from the intake valve system and gas before the fuel mixture goes to the engine. This ensures that the chainsaw is capable of continuing to run while it is in use. A bad carburetor will cause problems with how the chainsaw runs, and it may stop running during work. If the engine does not start when the tank is full of fresh fuel, test the carburetor. Start by removing the air filter and pouring a teaspoon of fuel onto the carburetor. Then, pull the starter rope to start the engine. If the engine starts but quickly dies, it means that the carburetor will likely need to be replaced. The replacement of the new carburetor is fairly simple. Remove the rear cover on the chainsaw to remove the old carburetor. Once you have removed the old carburetor, you can then install the new carburetor. Replace the cover and test the chainsaw. This is an OEM sourced part that will work with several models of chainsaws from Poulan and Craftsman.

This replacement carburetor kit is a genuine OEM parts kit for Craftsman hedge trimmers. The carburetor takes gasoline from the fuel line and mixes it with air from the intake valve to make a balanced fuel that is ready for combustion. Depending on how much fuel or air pass into the carburetor, the engine may run faster or slower. The most common reason for a carburetor to break down is if it is clogged with engine gunk. While it is sometimes possible to clean out a carburetor, if left for too long, the damage can be irreparable and the part will need replacing. First, remove the air filter and filter housing using a socket wrench. This will give access to the damaged carburetor and make it easier to unhook from the links that hold it in place. Be sure to set the gaskets firmly in place and then reassemble with the new part. This replacement carburetor is designed for use only with Craftsman appliances. It comes sourced directly from the original manufacturer and includes a carburetor and two gaskets.