Poulan Parts

This replacement driver spring is a genuine OEM part for a string trimmer with a starter rope ignition. When an operator pulls the starter rope, the rope must recoil back into the starter assembly before it can be used again. This spring connects to a driver pulley in the starter assembly and maintains the right amount of tension needed to recoil the pulley. Over time, driver springs will begin to lose some of their tension. This is especially true if the operator is quite rough on their appliance. Pulling too hard on the starter rope can wear out the spring more quickly, making it less effective. Without a properly tensed driver spring, the starter rope will not recoil into the assembly. To change out the spring, use a nut driver to open the starter assembly and remove the pulley to get access to the old spring. Carefully remove it and install the new part. This replacement driver spring is a high-quality part designed to match the exact specifications for a Husqvarna or Jonsered appliance. This part is sourced from its original manufacturer and ships individually.

This starter spring is a genuine OEM replacement part for chainsaws that operate using a starter rope. When an operator pulls the starter rope out, there is a pulley around which the rope then has to recoil. The starter spring maintains tension in the pulley so that the rope will naturally recoil. The starter spring also provides enough tension to prevent the operator from yanking the rope all the way out of the assembly. Through repeated use, and especially if an operator is rough on their appliance, the starter spring can loosen up and will no longer work as effectively. When this happens, the starter pulley will not recoil and the starter rope will hang loose from the appliance. Fortunately, switching out the starter spring is an easy repair that should only require a wrench and a pair of pliers. Be careful when pulling the old spring out. Although it isn't as tense as it once was, it still has the potential to snap back. This replacement starter spring is a high-quality part for Husqvarna, Poulan, and Weed Eater appliances, and as such, it is sourced from its original manufacturer. This part does not ship with any additional hardware.

A new rope kit may be necessary if the original rope becomes deteriorated or frays with regular equipment use.This rope is part of the recoil starter assembly, an essential component that enables the motor to be pull-started. Due to frequent usage and wear and tear, the rope can easily fray. Without this rope the engine cannot be manually pull-started. It is manufactured from durable nylon.This Husqvarna rope kit is a genuine OEM replacement part that has been sourced directly from the manufacturer. This replacement Husqvarna rope kit fits various different models of Husqvarna, Poulan, and Craftsman blowers, trimmers, and hedge trimmers. Please note this is sold individually. Handle grip not included.

This is a quality air filter used with many types of gas powered string trimmers. The air filter plays an important part in the engine since it ensures the motor only has clean air available. The air filter is responsible for catching dirt, dust, and other debris and collecting it in one place before it can move into other components of the trimmer. The air filter needs to be inspected on a regular basis for damage or clogging. If either of these things occurs, the air filter needs to be replaced to ensure the engine gets clean air.No tools are needed to replace this string trimmer air filter. The bolt knob that secures the air filter cover will need to be removed first. Remove the original air filter and place the new one in the same location. Reassemble the parts and make sure to test the string trimmer before use.This air filter is compatible with various string trimmers manufactured by Poulan, Poulan Pro, and Craftsman. It is sold as an individual component. It is an authentic OEM replacement part that is sourced directly from the manufacturer.

This starter assembly is a genuine OEM replacement part sourced directly from the manufacturer. It is found on trimmers and other outdoor lawn and garden equipment that utilize pull starts. This starter assembly is a recoil system that uses a pull rope with a handgrip, a starter pulley, and a starter spring. The grip is used to pull the rope, which releases the tension spring from the pulley. This causes the crankshaft to spin so that the engine starts. These parts are all covered by a plastic shroud to protect them from damage. However, normal wear and tear can lead to failure of the system. It can be easier and quicker to replace the entire starter assembly than it is to take it apart and replace one piece. Before removing the starter assembly, remove the spark plug. This repair requires a screwdriver to remove the old starter and install the new starter assembly. Do not misplace the screws; these are not included with the assembly. After the new starter is installed, reinsert the spark plug and pull the starter to check the repair. This starter assembly is sold as one complete, pre-assembled unit. The housing is durable black plastic with a nylon rope starter, plastic grip, and metal starter spring. Screws are not included. This unit is compatible with grass trimmers manufactured by Poulan and Husqvarna.

This is a gasket kit intended to replace three interior engine gaskets for several models of gasoline-powered Craftsman chainsaws. Chainsaws are particularly rugged power tools that see a great deal of pounding and dropping, as well as engine vibrations. All of these routine usage events result in wear and tear on the moving parts of the engine. Beyond sharpening the chain, keeping the air filter and carburetor working, sometimes it becomes necessary to replace internal engine parts, as well. Signs that the interior gaskets need to be replaced are a loss of power, an inability to get adequate RPMs from the engine to cut through wood, and continued leaking of oil from the engine manifold. The three gaskets in question, the cylinder gasket, intake gasket, and exhaust gasket, should all be replaced at the same. Whenever a sealed part of the engine is removed, the gasket that secures it to the rest of the engine should be replaced to assure air and oil tightness. Make certain when replacing these parts to use genuine OEM replacements like these. OEM parts are manufactured according to the specifications of the original parts and thus are a perfect match.