Poulan Parts

This sector gear plate is a genuine Husqvarna replacement part for appliances operated by small engines, including lawn tractors, lawn mowers, snowblowers, leaf blowers, chipper shredders, and tillers. A sector gear plate is affixed to the steer plate with a bolt and a washer, and its function is to assist in the turning of the wheels from left to right.A sector gear plate might have to be replaced in the event that it suffers damage over time, a common occurrence after long-term usage. The most prevalent form of damage to a sector gear plate is breaking or chipping away at its teeth, which prevents the sector gear plate from turning the wheels in a tight and controlled manner. If several teeth break off of the sector gear plate, a replacement sector gear plate part should be ordered and installed immediately to mitigate any possible further damage to the appliance. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This sector gear plate is compatible with the following brands: Husqvarna, Poulan, and Craftsman.

This no grease mandrel assembly is the part that houses the shaft where the mower blade attaches. It is mounted to the deck of the mower by three bolts, which are sold separately. The mounting holes on the mandrel housing are not threaded, but the bolts used to secure the mandrel to the deck are self-tapping. If the lawnmower is no longer providing an even cut, there may be a problem with the mandrel assembly. A broken or damaged mandrel assembly can severely reduce the mower's cutting performance. Replace it as soon as possible. The mandrel shaft goes through the deck, and the pulleys are attached to them, then the belt that drives the mandrels is placed in the pulleys. A spacer must be installed under the pulley. Failing to use a spacer or installing it on top of the pulley will result in damage to the shaft and pulley. This mandrel assembly is compatible with Ariens, Craftsman, Husqvarna, Poulan, and Weed Eater lawn mower models. It is an OEM part sourced directly from the manufacturer and is sold individually. The mandrel assembly includes a housing, shaft assembly, bearing, and nut only; the pulley/washer and blade bolt/washers are not included.

This wheel/tire assembly is a genuine Husqvarna part. The wheel is used as a replacement wheel for a lawnmower. The function of the wheels on a lawnmower is to steer and drive the lawnmower over various surfaces. Lawnmower wheels have an average lifespan of about five years. A wheel might have to be replaced sooner than that in the event that it suffers from serious gradual or sudden damage; this damage could take the form of punctures, cuts, and burns, among other forms of damage. The symptoms of a wheel that is due for a replacement are unusually rough riding, less traction than usual when moving the lawnmower uphill and downhill. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This wheel is compatible with Husqvarna brand lawnmowers. This part is sold individually.

A chainsaw clutch drum works by driving the chain along with the gear. The gear and clutch drum are engaged by the clutch when the engine’s speed picks up. The chainsaw clutch drum likely needs replacement when the chain isn’t turning. This repair is easy to complete and can be accomplished with minimal tools. The hardest part of this repair might be the removal of the old chainsaw clutch drum in cases where they are misshaped or warped from damage from continual friction. Many will work well past the point when they should be replaced, so it is essential to monitor your chainsaw parts for noticeable signs of disrepair or inefficiency. This chainsaw clutch drum is compatible with Craftsman and Poulan chainsaws. It is a high-quality genuine OEM clutch consisting of durable metal.

A clutch cover assembly is bolted to the engine and has the clutch disc between it and the pressure plate. The springs within the clutch cover will force the pressure plate against the disc, moving it against the flywheel to send power into the manual transmission. This is a clutch cover assembly for Husqvarna and Craftsman chainsaws, including gear with the Poulan named attached. This is the cover for the assembly and ships as an individual part. It does not contain any of the other components associated with the transfer of power to the transmission.

This is a ready-to-install fuel tank assembly designed for use on trimmers. It is made of high-quality plastic. The assembly includes a translucent tank, a fuel filter inside the tank, an attached fuel tank cap, and a fuel line hose. If the trimmer is leaking gas, check the fuel tank, cap, fuel lines, grommets, fuel filter, and the primer bulb. Options include replacing individual parts depending on which components are damaged or installing a new fuel tank assembly. Remember that any gas-leak related incident requires immediate attention. This is an OEM replacement part sourced directly from the manufacturer. The assembly kit is compatible with specific trimmer models from Craftsman, Weed Eater, and Poulan. It is sold individually.

This driveshaft assembly is designed to connect the cutting head to the drive motor assembly in pruners. With proper operation, it powers the head to perform the cutting work. When the driveshaft wears down over time or becomes damaged in some way, it will need to be replaced. The driveshaft performs a repetitive motion which makes it more prone to needing replacement sooner than other parts. This driveshaft is a genuine OEM replacement that is designed specifically for Husqvarna and Poulan trimmers and pole pruners. It offers an exact fit for compatible equipment and can even be added as a secondary shaft to get a little more length for trimming. This shaft is simple to replace or install and only requires basic tools. It is sold individually and made of durable materials. Pruners are designed to make outdoor work easier and having a properly functioning, high-quality driveshaft will make all the difference in its operation. Remember to disconnect the spark plug and wear gloves when doing repair work.

This chainsaw fuel cap assembly is made from high-quality plastic. Durable threads keep this chainsaw fuel cap assembly working for years of use. You place one end in the fuel tank while the screw cap covers the nozzle. This keeps your gas from spilling out and causing possible damage or injury. You can’t cut down a tree or slice up some firewood with gas leaking everywhere. This also leads to harming the environment around you. Chainsaws fuel caps can swell. The rubber seals may leak after a certain amount of use. The cord attaching the cap to the insert may break, allowing the cap to be lost. Replacing the chainsaw fuel cap assembly can correct these problems. Pliers or a wrench may be needed to remove the old fuel cap assembly. This genuine OEM chainsaw fuel cap assembly was manufactured for use with Craftsman chainsaws. It is also compatible with Poulan and Poulan Pro chainsaws.

The clutch connects to the crankshaft of the chainsaw engine. The crankshaft turns the up and down motion of the pistols into a rotation, which turns the drum and makes the chain go around. As the inner drum of the clutch starts to wear out, it puts more and more pressure on the springs, causing them to break. So, without a properly functioning clutch, the engine will run, but the blade will not turn. Replace the chainsaw clutch assembly using our genuine OEM part sourced directly from the manufacturer. A socket wrench and a screwdriver will be needed. Start by removing the chain brake cover to gain access to the clutch. Remove the chain and bar and then bind the piston in place. From there, use a screwdriver to remove and replace the clutch. This part is compatible with Poulan or Craftsman brand products. Sold individually.

This genuine OEM replacement part is a rebuild kit of various gaskets used in a gas-powered leaf blower engine. This kit includes a crankshaft gasket, a carburetor gasket and carburetor adapter gasket, a cylinder base gasket, and a muffler shield. Gaskets act like a seal between different parts of an engine that keeps different liquids and gasses from passing into the wrong section of the engine. Gaskets can become worn out and crack or shrink over time through repeated use and exposure to exhaust and heat in the engine. A common sign of a fault gasket is if your engine is not running at full capacity or if it stalls out shortly after ignition. Changing out a gasket should not be a difficult job, but it will depend on which gasket you are replacing. Making this repair will require a screwdriver and set of pliers. This gasket rebuild kit is compatible with Poulan, Weed Eater, and Husqvarna gas powered leaf blowers. These gaskets are made of a mix of plastic and rubber. This kit ships individually and is sourced directly from its original manufacturer.

This cylinder head is a genuine Husqvarna part, sold individually. This cylinder head can be used as a replacement part in a leaf blower. The purpose of the cylinder head in a leaf blower is to affix to the top of the cylinder block and close off the combustion chamber within the cylinder, so that airflow in and out of the cylinder block can be regulated and controlled to exact specifications for standard use of the leaf blower.The cylinder head in a leaf blower might have to be replaced if the cylinder head is dented, punctured, scraped, torn, cracked, chipped, or otherwise damaged to the point of exposing the internal combustion chamber to the elements or to possible leakages from the inside or outside of the component. If this occurs, the cylinder head should be removed and replaced by this genuine OEM replacement part.This OEM part is a genuine replacement that is sold individually and sourced directly from the manufacturer. This cylinder head is compatible with the following outdoor appliance brands: Husqvarna, Craftsman, Weed Eater, Poulan, and Poulan Pro.

This genuine carburetor repair kit is designed for use in select trimmer engines. The carburetor is responsible for combining the gas and air mixture that will go into the engine. Fuel and air flow into the carburetor through filters to remove any potential debris or particulates. Then, they are passed through a series of tubes and diaphragms and mixed together in the inner tube before being released into the engine through a butterfly valve. Over time, the high heat and constant pressure can damage the gaskets, diaphragms, and other parts of the carburetor. It may be necessary to replace everything with this carburetor repair kit that includes multiple components. This genuine OEM carb kit is compatible with select lawn and garden trimmers from Craftsman, Poulan, Weed Eater, and Jonsered. There are more than 50 compatible models available that can use this kit. This carburetor repair kit comes with 16 pieces in total, including the gaskets and diaphragms, the primer bulb and primer bulb assembly, and other necessary hardware. It is sold as a single unit. Always cool the engine completely and work in a well-ventilated area when performing carb rebuilds and replacements or other engine repairs.

This is an OEM replacement starter pulley kit designed for use with gas chainsaws. The starter pulley assembly replaces the components of your recoil starter that may fail due to normal wear and tear. The pulley and return spring react to the pull of the starter rope and then engage the flywheel. This is what fires the chainsaw engine. If the starter rope is not reacting or the flywheel is not engaging, there may be an issue with the starter pulley assembly. This repair can be completed with a screwdriver and pliers and doesn’t take a lot of time. This starter pulley kit is a genuine product from Husqvarna, and it is designed for use with Poulan, Jonsered, and Husqvarna engines and outdoor power equipment. This kit includes the plastic pulley, return spring, hub, and two screws for securing the unit. The housing, rope, and starter grip will be sold separately if replacements are needed.