Parts for Bosch SHU3307UC/14: Pump Parts

Removes residue, odor-causing soils, and food particles from dishwasher tub and gasket. Use monthly to eliminate unwanted odors and maintain peak performance.

Fix dishwasher not heating or running for hours. This NTC temperature sensor monitors water temp and prevents overheating. Moderate DIY repair with video.

Seals the NTC temperature sensor port in your dishwasher to prevent leaks and ensure accurate temperature readings. Replace if leaking or worn. Verify fit with your model number before ordering.

Circular sealing gasket creating watertight joints between dishwasher components. Replace when flattened or cracked to prevent leaks. Confirm fit by model.

Seals the dishwasher sump to prevent water leaks during wash cycles. Replace if you notice leaking at the base or constant drain pump operation.

Secures the dishwasher sump or sump cover to the tub for a tight, leak-resistant seal. Replace if missing, stripped, or damaged to restore stability.

Secures the sump assembly to the tub, preventing leaks and movement. Replace if worn, cracked, or if you notice water leaking from the base of your dishwasher.

O-ring seal prevents leaks between dishwasher components. Replace when you notice water drips or moisture buildup. Confirm fit with your model number.

Plastic cover that protects the drain pump mechanism from debris. Replace if cracked, broken, or tabs are bent preventing proper seal during drain cycles.

Fix a dishwasher that won't drain or makes grinding noise during drain cycle. This pump removes dirty water from the tub. Easy 5-15 minute replacement.

Fix dishwasher not draining or foul odors with a new check valve. Prevents dirty water backflow into clean dishes. DIY-friendly repair in 1-2 hours.

Dishwasher not draining or water pooling at bottom? A cracked sump disrupts water flow to the pump. This housing restores drainage and prevents leaks.

Rear pump housing for the washer drain/pump assembly. Replaces the worn rear housing that supports the impeller and bearing, helping restore proper draining and reduce leaks or unusual pump noises when the housing fails. What it does:

• Houses and supports the pump impeller and bearing, forming the rear half of the drain pump assembly.
• Restores a sealed mounting surface to help prevent water leaks from the pump area.
• Helps re-establish correct water flow and draining when a cracked or worn housing impairs the pump.
• Addresses symptoms such as poor or no draining, water at the base of the appliance, or loud/grinding pump noises.

• Disconnect power and shut off water supply before starting; drain any standing water to avoid spills.
• Remove the washer access panels and pump assembly; transfer the impeller, seals, and any hardware as required.
• Inspect and replace pump gaskets/seals and the impeller if worn; tighten mounting fasteners to OEM torque where specified.

This circulation pump repair kit is a genuine Bosch part, sold individually. This circulation pump repair kit can be used as a replacement part for a dishwasher. This part supplies all of the necessary components to facilitate the replacement of the dishwasher impeller and seal. The impeller of a dishwasher sprays and drains the water during a standard dishwasher cycle, and the seal keeps the interior of the dishwasher protected from external materials.A circulation pump repair kit might have to be ordered as a replacement part for the impeller and seal of a dishwasher in the event that the impeller and the seal suffer damage that prevents the components from serving their dual functions. Damage can include punctures, tears, scrapes, or warping from general wear and tear or as the result of a direct impact collision with a hard object. If this occurs, the circulation pump repair kit should be ordered as a complete, genuine OEM replacement part.This is an OEM part sourced directly from the manufacturer. It is sold individually. This circulation pump repair kit is compatible with the following appliance brands: Bosch, Kenmore, Thermador, and Gaggenau.

Removes residue, odor-causing soils, and food particles from dishwasher tub and gasket. Use monthly to eliminate unwanted odors and maintain peak performance.

Secures the hose between pump and heater in your dishwasher. Replace if loose, damaged, or causing leaks. Confirm fit with your model number.

Pump housing cover for dishwashers. Replaces cracked, broken, or missing covers that protect the pump assembly. Installs over the pump mechanism.

Support strap that cushions and secures the dishwasher circulation motor, stabilizing the motor assembly to reduce vibration and help maintain alignment for steadier, quieter operation. Designed for circulation motors with softer bearings. What it does:

• Cushions and supports the circulation motor to limit movement and vibration and reduce motor noise.
• Secures the motor assembly to the tub/chassis to maintain proper clearance and fit.
• Helps prevent undue stress on motor bearings and mounting points that can cause premature wear.
• Commonly replaced when the strap is cracked, stretched, or no longer holds the motor firmly in place.

• Disconnect power and water supply before servicing; follow all safety and OEM service instructions.
• Remove access panels and any obstructing components to reach the circulation motor as required.
• Replace using the original mounting hardware; inspect motor mounts and bearings while accessible.
• Reassemble and run a short test cycle to confirm reduced vibration/noise and proper motor operation.

Hose, with o - ring, shu (uc/12 & above)

This Sump to Float Hose is an OEM part for Bosch Dishwashers. It functions to carry water from the dishwasher sump to the float assembly. Continuous water flow and exposure to detergents can lead to wear or damage over time.

What Causes a Bad Sump to Float Hose:
Exposure to chemicals and hot water, along with wear from water flow, can cause the hose to degrade or develop cracks.

Symptoms of a Bad Sump to Float Hose:

• Water leakage around the dishwasher
• Incomplete or interrupted washing cycles
• Visible cracks or damage to the hose

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

The Water Inlet Fill Hose is an OEM part for Bosch dishwashers. This part is responsible for safely and efficiently connecting the dishwasher to your home's water supply, ensuring that water flows into the dishwasher at the correct pressure and volume for optimal cleaning performance. 

Over time, the Water Inlet Fill Hose can become susceptible to wear and tear, leaks and blockages.

Symptoms indicating the need for a new Water Inlet Fill Hose include:

• Water pooling around the dishwasher base, pointing to a potential leak in the hose.
• The dishwasher not filling with water properly, or filling very slowly, suggesting a blockage or damage to the hose.
• A visible inspection reveals cracks, bulges, or signs of corrosion on the hose connectors.

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

Dishwasher won't fill or keeps overfilling? The float switch detects water levels for proper filling and draining. Accessible repair in under 30 minutes.

The Pressure Chamber is an OEM part for Bosch dishwashers. This part is responsible for monitoring and controlling the water level within the dishwasher. It operates by sensing the pressure exerted by the height of the water in the tub and ensures that the dishwasher fills with the correct amount of water for optimal cleaning performance.

Causes for replacement may involve wear and tear over extended use, mineral buildup affecting the switch’s sensitivity, or electrical faults leading to inconsistent performance.  

Symptoms of a failing Pressure Chamber include:

• Overfilling or underfilling of the dishwasher, which can lead to inadequate cleaning or potential water damage.
• Unexpected changes in the wash cycle, such as sudden stops or pauses.
• The dishwasher not starting a wash cycle due to incorrect water level readings.

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

Water level regulator.

Replaces cracked or brittle dishwasher hose connecting the sump to the water inlet valve. Includes 2 o-rings. Essential for preventing leaks during pump replacement or routine maintenance.

Spring-style hose clamp secures water and drain hoses to fittings, preventing leaks. Replace when connections loosen or clips lose tension. Confirm fit with your model number.

Replacement water level control cover for dishwashers. Snaps over the water level control assembly. Order a new cover if yours is broken, cracked, or missing.

Fix a dishwasher that won't fill, overfills, or leaks from the base. Water inlet valve controls flow into the tub. Moderate DIY repair, 30-45 minutes.

Fix dishes not drying or cycles taking 3+ hours. This heating element heats wash water and enables drying. Moderate DIY repair with video guide.

This turbidity sensor detects how clear the dishwasher's wash water is so the control can adjust cycle time, rinses, and water changes. Replacing a faulty sensor helps restore proper cleaning performance and normal cycle lengths.

• Monitors soil level/clarity of the wash water
• Signals the control to extend or shorten wash and rinse phases as needed
• Helps optimize water use while maintaining cleaning results
• Failure symptoms can include unusually long or short cycles, poor cleaning, repeated draining/refilling, or cycles that won't advance

• Disconnect power and turn off the water supply before servicing
• Pull the dishwasher out as needed; access the sensor from the base area
• Place a towel to catch residual water; release the locking tab or twist-lock, unplug the connector, and install the new sensor fully seated and locked
• Restore power/water and run a test cycle; check for leaks

Seals the aqua sensor assembly to prevent water leaks and protect electronics. Replace if you notice leaks or sensor errors. Confirm fit with your model.

Removes residue, odor-causing soils, and food particles from dishwasher tub and gasket. Use monthly to eliminate unwanted odors and maintain peak performance.