Bert June 14, 2013 for Model Number GLTF1040AS0 Washer fills with water and drains but will not agitate on wash cycle or on spin cycle. Also the timer runs through the wash cycle in 3 or four minutes. What could the problem be?
1 Answer Bert, You will want to check the door lock on the unit and check for any error codes that are on the unit. If you could locate the tech sheet it will tell you how to access the error codes. This will tell you what needs to be checked for the unit not agitating and spinning. Read More...
Mark O May 08, 2013 for Model Number GLTF!)$)ASO My frigidare front load washer on any wash cycle will start to run and wash clothes during after the rinse and drain it seems to stop and just hum if i advance the timer a little bit it than continues with spin cycle. I believe it to be the timer what do you think. No other problems
1 Answer Mark, If the timer is stopping right before the spin cycle then it does sound like the contacts may be sticking and timer 137394200 would need to be replaced. Read More...
1 Answer Hello Ron! Yes, the timer part number 137394200 is the manufacturer replacement for 131802100E/131802100. Thanks! Read More...
Bill F August 13, 2012 for Model Number 41744102301 The timer keeps on moving clicks, but dose not stop for any cycle to start, then light comes on.
1 Answer Hello Bill. If the timer continues to run, and does not stop, you will need to order and replace the timer 137394200 on the unit. Read More...
Darl July 30, 2012 for Model Number 41744102301 Washer has power and water. Does not come on at all. Only the door lock light comes on when I put it into a wash mode.
1 Answer Hello Darl. If the door lock light is coming on, you need to check and make sure the lock assembly is working on the unit. If not, you may have a bad door lock assembly 131763256 and need to replace the door lock assembly. Read More...
Dan October 03, 2011 for Model Number Frigidaire Front Load Washer Model FWT647GH S Washer drains about half the water and quits - right when it would normally begin the spin cycle. Timer doesn't advance. I can not continue draining or start the spin cycle by manually advancing the timer. Frigidaire Front load Washer Model FWT647GH S
1 Answer Hi Dan. Remove power. remove top. Access the tech. sheet inside and compare any fault codes given. Loose connections? Pump clogged or hoses clogged? Are there any clothes/debris' in the front of the basket or the belt/ motor stuck? Is the motor windings hot and opening? Remove the fill hoses and inspect the inlet valve screens for clogged or neds replaced. Water valve is part # 134190200. Let us know how we can assist further. Read More...
Erna July 09, 2011 for Model Number AP5184476 Our Frigidaire front load washer sometimes keeps on going on the pump cycle until we manually turn the knob to the spin cycle. And other times it stops in the middle of the wash cycle until we turn the knob again. Do you think we need to replace the timer? After we turn the knob the washer washer usually complete the cycle until done.
1 Answer Hello Erna. According to the model number FWT645RHS0 you provided, you will need to check and make sure the pump assembly 137108000 and the hose 131784700 from the pump to the tub is not clogged. If so, it can cause the problems you having. If it is clear, and you still have the problem, you will need to replace the timer 137394200. Hope this helps. Read More...
David May 17, 2011 for Model Number 417.94042500 My stackable dryer works but will not heat up.It lights up but then goes out before it can burn the gas. I replaced the 2 gas valve coils. I checked the igniter its ok. I checked the flame sensor its ok. I looked but cannot find a thermal fuse on this dryer. Can you tell me what the problem is to repair this dryer? Does this dryer have a thermal fuse, if so where is it located? Or is there another part causing this dryer not to heat up?
1 Answer Hello David! You will need to test the cycling thermostat 134048900 and the safety thermostat 5308015399. Hope this helps! Read More...
David May 17, 2011 for Model Number 417.44102300 My wash cycles work fine. But after it finishes the wash cycle & finish spinning, it do not automatically go to the next cycle which is the rinse cycle. I can turn it manually for it to go to the next cycle & it will work. The front knob for the timer is cracked / broken. Do this sound like the timer & knobs beed to be replaced?
1 Answer Hello David. From what your describing, it does sound like the timer 137394200 and the knob 134191800 will need to be replaced. Hope this helps. Read More...
April March 24, 2011 for Model Number Frigidaire Gallery GLTF1040ASO When I start a wash cycle the water does not immediately begin to flow as it used to. It does start when I click one space further to the right. Do I need to replace the timer or is this another issue entirely?