Christian December 06, 2016 for Model Number whirlpool duet dryer gew9250pw1 Dryer kept shutting off periodically tripped breaker , progressed to lock control lock being stuck with no operational ability. Ii replaced control panel, worked great for one day, now no lights on dryer extremely dim on selection wheel, now no operational ability. Is there a short somewhere? Did I just fry a new board?
1 Answer Christian, First check and make sure there is proper power supplied to the dryer. If you replaced the WP8546219 Machine control board, then you need to check or replace the WP8558753 user interface control board. If you remove the lower front access panel, you should find the tech data sheet attached to the back of the panel and can conduct the diagnostics and test modes for the controls. Read More...
Jaime November 21, 2016 for Model Number GGW9250PW0 The control panel on my Duet mode GGW9250PW0 will only turn on if the selector knob is set to Heavy Duty, Timed, or Touch Up. For all other settings there is no response. Once the control panel does turn on, some buttons will respond correctly, but other buttons are either ignored or activate an incorrect function. Do I need a user interface board or control board?
1 Answer Jaime, The control panel not responding would be caused by a faulty user interface board. Read More...
Robert October 20, 2016 for Model Number GEW9250SU0 The controls are our Duet dryer are getting power (they're lit up) but none of the controls work. It's like the control panel is in a lock out mode. Would this be a dryer control board problem?
1 Answer Hello Robert. Yes, if the panel is not locked, you will need to order and replace the control board WPW10128437 on the unit. Read More...
Jmann October 19, 2016 for Model Number GGW9250PW3 The machine has been having trouble for a little bit. Previously when we had trouble I unplugged for a little while, and I guess reset the machine and it worked again. Now, I cannot get the machine to go into diagnostic mode at all. No buttons light up. Power is getting to the machine - but I can't get anything to work. I am assuming this is the control board - but is there a way to tell if it is that versus the button panel or something else?
1 Answer Jmann, There is really no way to test the display other than checking to make sure that the ribbon connector from the user interface is seated fully with the main control board. Read More...
Jay October 09, 2016 for Model Number WED9400SW1 My Whirlpool Duet will not heat. I am getting codes F70 and L2...I am thinking the control panel has gone out. Any suggestions?
1 Answer Hello Jay. F:70 / F:71 flashes when there is no communication betweenthe machine control and the console electronics. You will need to replace the main control board in the unit. Also, check the line voltage coming to the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Alex August 28, 2016 for Model Number GEW9250PW1 Hello. On my dryer - Whirlpool Duet, the control lock light lits up on its own and I cannot cancel it by holding the proper button for 3 seconds. I had turned the power off for a day and somehow I was able to turn it off and used the dryer for a day or two, but at some point it went on on its own and I cannot turn it off any more. I tried turning the power of etc but nothing worked. What part do I need to replace? - the control board or the control panel with the buttons? Thanks
1 Answer Alex, The user interface would be the most likely cause for the unit to turn the lock on by itself and would be part number WP8558753. Read More...
Brant August 06, 2016 for Model Number 110.85088401 My kenmore elite he4 dryer will not come on. The light comes on when opening the door. I've had a technician come out and said to replace the user interface which i did and it worked for a day and then back to not working. I've tested everything from moisture sensor to heating element and everything is working properly. When i do get it into diagnostic mode i get zero errors. Could this be the main control board?
2 Answers Hello Brant, You should check the thermal fuse WP3392519. The door switch WPW10318609, belt switch 279782, and centrifugal switch in the motor assembly 279787 should also be checked. I'm sorry but this part WPW10318609 has been discontinued by the manufacturer and no satisfactory substitutions have been provided. Read More...
Brant August 06, 2016 for Model Number 110.85088401 My kenmore elite he4 dryer will not come on. The light comes on when opening the door. I've had a technician come out and said to replace the user interface which i did and it worked for a day and then back to not working. I've tested everything from moisture sensor to heating element and everything is working properly. When i do get it into diagnostic mode i get zero errors. Could this be the main control board?
2 Answers Brant, If the thermostats and thermal fuses check ok then yes the main control board would be the most likely cause for the unit to not work. Read More...
Alex July 29, 2016 for Model Number GGW9250PW2 You can open the door the light comes on but none of the controls light up and you can not obviously make the dryer work at all. Where should I start looking?
1 Answer Hello Alex. You will need to test the thermal fuse and the power supply to the unit. If both are good then it sounds like the main board is bad on the unit. Read More...
Kim June 27, 2016 for Model Number WGD9400SW0 The dryer is beeping. But functioning correctly. The sensors were cleaned and that fixed the beeping temporarily.
1 Answer Hello Kim. Replace the sensors. If the issue continues, then replace the control board on the unit. Read More...