Range / Cooktop / Oven Valve

This control valve is an important safety feature found on many gas ranges. It's located inside the back of the range near the area where the buttons and controls are found. The reason the control valve is included in ovens is to prevent gas from moving to the burners if the igniter is not able to ignite the gas or there is no electricity. The control valve could be faulty if there is a smell of gas near the valve, the burner flame flickers, or the flame cannot be turned on high.In any of these situations, the control valve must be replaced. The repair is easy and takes only a few minutes. The bottom of the oven will need to be removed, which may require a screwdriver. After removing it, remove the flame spreader by taking out two screws and sliding it out of the oven. Remove the screw holding the oven burner tube and take it out to access the valve and replace it.This control valve is made to be compatible with RCA, Kenmore, Roper, General Electric, and Hotpoint ranges. It's sold as an individual OEM replacement part that is sourced directly from the manufacturer.

This water inlet valve controls water flow to the refrigerator's ice maker and dispenser, restoring normal ice production and water dispensing when the valve fails. Durable direct-fit replacement for affected GE refrigerators. What it does

• Opens and closes to supply water to the ice maker and dispenser when the dispenser or ice maker calls for water.
• Commonly used to fix no-water or low-water flow to the ice maker or dispenser.
• Stops water flow when the refrigerator is off to prevent leaks or flooding.
• Works with electrically controlled solenoid valves in the water system.

• One water inlet valve

• Disconnect power and shut off the household water supply before starting work.
• Access may require removing interior panels, the back cover, or toe panel depending on the model.
• Replace using the existing mounting and wiring connections; use new water line fittings if old fittings are corroded.

Replacement burner valve that controls gas flow to a surface cooktop burner, restoring reliable flame control for safer, consistent cooking. Use this valve when a burner has low or no flame, uneven flame, or won't respond to knob adjustments. What it does:

• Regulates gas flow to a single surface burner so you can adjust flame size and cooking heat.
• Replaces valves that cause burners to fail to light, produce weak or sputtering flames, or not change flame level.
• Restores normal burner operation when the original valve is worn, leaking, or damaged.
• Compatible with gas cooktops and ranges.

• Turn off the gas supply and unplug the appliance before starting any repairs.
• Use appropriate hand tools; avoid overtightening fittings or damaging gas lines.
• After installation, check all connections for leaks (soap-and-water test) and verify proper burner ignition and flame.

This genuine OEM part is an oven safety valve for gas ovens. The oven safety valve is designed to prevent gas from flowing to the burner assembly if the igniter is not hot enough to ignite the gas, or if no electricity is present. Over time, an oven safety valve can become inoperable due to excessive wear and tear. If the oven is no longer heating properly, not turning on, or no longer working as powerfully as it once did, the oven safety valve will need to be replaced.To replace this part, start by unplugging the oven and shutting off the gas supply. After that, move the range away from the wall. Use a wrench to unthread the nut to remove the gas supply tube from the safety valve. Next, open the oven door to gain access to the interior of the oven. Release the hinge locks that secure the door and pull the door off the oven. Remove the oven racks and proceed to unthread the screws that secure the oven's bottom panel. Once removed, locate the safety valve. Next, unthread the screw that holds the mounting bracket into place. Remove the old safety valve and align the new valve with its mounting bracket. Attach the wires to the safety valve terminals and reinstall the bottom panel and oven door.This replacement part is sold individually and is sourced directly from the manufacturer. It is compatible with General Electric, Hotpoint, and RCA brand ovens.

This is a replacement surface burner gas valve. It controls gas flow to a cooktop/range burner so you can safely turn the flame on/off and adjust heat. Replacing a worn or leaking valve restores precise flame control and safe shutoff. What it does:

• Opens and closes to supply gas to a surface burner
• Provides smooth flame modulation from low to high
• Helps ensure a complete shutoff in the Off position
• Common symptoms: knob hard to turn or loose, gas odor at the control area, flame won't adjust or won't shut off completely

• 1 gas valve

• Disconnect power and shut off the gas supply before servicing
• Note valve orientation and tubing layout before removal
• Use an approved gas-rated thread sealant on male pipe threads; do not overtighten
• After installation, leak-test all connections and verify proper burner operation

This burner valve controls gas flow to a surface range burner to produce and adjust the flame for cooking. Replacing a faulty valve restores proper ignition and flame control for safe, even heating. What it does

• Regulates gas flow to the surface burner so the flame lights and adjusts with the control knob
• Enables consistent low-to-high flame response for normal cooking
• Can fix symptoms like a burner that won't light, has no flame, or won't hold a steady flame
• Works as the control point between the cooktop control and the burner assembly

• Turn off gas supply and electrical power before starting; follow all safety procedures.
• After installation, check all gas connections for leaks using a proper gas leak test method.
• Do not use the appliance if you detect a gas odor; shut off gas and ventilate area.

This burner valve controls the flow of gas to a single surface burner, restoring proper burner ignition and heat control. It's a direct-replacement gas valve that helps fix intermittent or no-flame burner operation. What it does:

• Regulates gas flow to one surface burner so the burner lights and the flame responds to the control knob.
• Replaces a valve that is stuck, leaking, or not allowing gas through, which can cause a burner to fail to light or produce a weak/unsteady flame.
• Works with pilot/ignition systems to ensure consistent ignition when the knob is turned.
• Helps eliminate clicking or continuous sparking caused by failed gas delivery (when ignition sequence is otherwise OK).

• One burner valve

• Turn off the gas supply and unplug the appliance before starting any work.
• Verify valve orientation and connections match your appliance.
• Use approved fittings and check all gas connections for leaks with a soap solution or gas leak tester after installation.
• Do not attempt repairs if you smell gas; ventilate the area, avoid open flames.

This valve kit repairs the appliance's water/control valve assembly and provides the small mounting screw needed for secure installation. It replaces a worn or damaged valve kit so the appliance can restore proper valve function. What it does:

• Replaces the valve assembly components that control water flow or internal fluid routing
• Helps stop issues caused by a damaged valve kit, such as inconsistent water delivery or valve leakage
• Restores secure mounting with the included screw to prevent loose fittings
• Works as the direct replacement kit specified for the original valve location

• Disconnect power and shut off water supply before starting any repair
• Handle valve components carefully to avoid damaging seals and fittings
• Use basic hand tools; avoid overtightening the mounting screw to prevent stripping

A replacement surface burner valve that controls gas flow to a cooktop burner for consistent flame and heat. Restores proper burner response so burners light and adjust as expected. What it does

• Regulates gas flow to a single surface burner so flame size responds to the control knob
• Helps resolve a burner that won't light or produces little or uneven flame
• Replaces a worn or faulty valve that causes inconsistent temperature during cooking
• Use with the corresponding manifold and control knob assembly for full operation

• One burner valve (surface)

• Turn off gas supply and disconnect power before servicing; follow all safety procedures
• Inspect connections and fittings for proper sealing; check for leaks after installation with a soap solution
• Handle components carefully to avoid damage to valve ports and threads

The Valve-Gas is an OEM part for Whirlpool gas stoves. It controls the flow of gas from the supply line into the burner tubing, igniters, and flames themselves during the operation of the range top. Precise control of gas flow is critical for safe and efficient cooking performance.

Symptoms of a bad gas valve can include:

• Inability to ignite one or more burners  
• Unstable, intermittent burner flames
• Burners that cannot be turned low enough or click off suddenly 
• Escaping gas odor near the range

Causes of a bad valve may involve wear and tear of internal parts like diaphragms or seals letting in air/gas, corrosion on valve surfaces from gas or moisture, or damage from appliance service/movement over time. 

This Whirlpool OEM replacement part is compatible with Maytag, Jenn-Air, Amana, Magic Chef, and select Kenmore models.

The Safety Valve Assembly is an OEM part for GE gas ranges. It automatically cuts off gas flow if excess pressure develops, providing critical safety protection.  

Symptoms of a faulty safety valve include:

• The range does not ignite and burners fail to light
• Gas leaks occur even when burners are off
• Responsiveness issues adjusting burner flames 

 Causes involve worn seals, dirt/debris blocking valve ports, or cracked componentry from shock over time.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This safety valve controls and shuts off the flow of gas to the appliance, helping the cooktop or oven heat safely and reliably. It replaces a failed valve to restore proper gas control and safe operation. What it does:

• Regulates gas flow to the appliance's burner assembly and/or pilot circuit
• Stops gas flow if the valve or control circuit fails, preventing unsafe leaks
• Common symptom: appliance won't heat or burners won't light despite power to the igniter
• Common symptom: intermittent heating or unit shuts off unexpectedly during operation

• One safety valve

• Turn off gas supply and disconnect power before servicing
• After installation, check all gas connections for leaks and verify proper ignition and shutoff operation
• Do not attempt repair if you smell gas; evacuate area.

This surface burner valve controls gas flow to a cooktop burner for reliable flame adjustment and safer operation. Replaces a worn or leaking valve to restore consistent heat and proper burner control. What it does:

• Regulates gas flow to a single surface/burner for simmer-to-high flame control
• Stops gas flow when turned off to prevent leaks
• Addresses symptoms like weak or uneven flame, burner not lighting, or gas odor (stop use and check immediately)
• Works as the control point between the cooktop knob and burner

• Turn off the appliance power and shut off the gas supply before starting any work
• Work in a well-ventilated area and check for gas leaks after installation using a leak-safe method (soap solution or approved detector)
• Use proper tools and replace any damaged fittings or seals; tighten connections to manufacturer torque where specified

This water inlet valve controls water flow to the refrigerator dispenser and ice maker, restoring proper dispensing and ice production. It replaces a failed or leaking valve to stop drips and ensure steady water fill. What it does:

• Opens and closes water supply to the dispenser and ice maker when activated
• Stops water flow to prevent leaks when the valve is closed
• Helps restore normal dispenser flow and consistent ice maker fills
• Commonly replaced for leaking, no water dispensed, or weak dispenser flow

• Disconnect power and shut off the water supply before starting any work
• Drain lines and have towels ready; valve replacements can release trapped water
• Basic hand tools required; avoid overtightening fittings to prevent damage

This water inlet valve controls water flow to the refrigerator's ice maker and dispenser so ice production and water dispensing work reliably. Replaces a worn or failed valve to restore proper filling and water delivery. What it does:

• Opens and closes water flow to the ice maker and dispenser when signaled
• Can stop water flow when the valve or solenoid fails, causing no water or no ice
• A worn valve may cause weak/no water dispensing or slow/fail ice production
• May leak if seals or valve body fail, so replacement stops persistent leaks from the inlet area

• Disconnect power and shut off the water supply before starting any work
• Install in the same orientation and secure inlet/outlet fittings per OEM instructions
• Inspect tubing and fittings for damage and replace any compromised parts to prevent leaks