Range Valve

This safety valve controls gas flow to the cooker's burner assembly, restoring regulated gas delivery for safe operation. It's a direct-replacement-style valve used when the oven or range won't heat or won't light properly. What it does:

• Regulates and permits gas flow to the burner when the oven/range calls for heat.
• Can address symptoms such as burners or oven failing to ignite, inconsistent heating, or loss of burner control.
• Designed to work with the appliance's existing gas line and valve mounting points.
• Acts as a replacement component (one-for-one swap) for the original valve assembly.

• Turn off gas supply and disconnect power before inspecting or replacing the valve.
• Replacement may require basic gas-line fittings; follow the appliance manufacturer's installation instructions.
• After installation, test all gas connections for leaks and verify proper operation per local codes.

This valve lockout mounting clip secures the appliance's gas valve actuator to help prevent unintended valve movement and ensure consistent operation. It replaces a worn or broken lockout clip to restore reliable valve positioning. What it does:

• Secures the gas valve actuator or linkage to keep the valve in its intended position
• Helps stop intermittent or loose valve movement that can cause inconsistent ignition or burner operation
• Restores proper mechanical alignment after the original clip has cracked, bent, or broken
• Small replacement part used where a damaged lockout clip prevents stable valve function

• One valve lockout mounting clip

• Disconnect power and shut off gas supply before servicing; follow all safety precautions
• Inspect adjacent fasteners and actuator for damage; replace any additional damaged parts as needed
• Basic hand tools typically required; handle small plastic clips carefully to avoid breakage

The Valve Control Assembly is an OEM part for GE gas ranges. It regulates the flow of gas to burners via integrated solenoid valves, ensuring safe ignition and temperature control during cooking cycles. 

Causes of a bad Valve Control Assembly can include:

• Mineral or debris buildup affecting gas flow
• Overheating warping critical valve housing parts
• Worn solenoid valves inhibiting proper opening/closing

Symptoms include:

• Uneven or inconsistent burner flame levels
• Difficulty maintaining selected temperature settings
• Burner ignition issues requiring service calls
• Potential gas leaks from faulty valve sealing integrity

This GE replacement part is compatible with Hotpoint, RCA, and some Kenmore models.
 

This safety valve controls gas flow to the range/oven burner and helps ensure reliable ignition and shutoff for safe cooking. Replacing a worn valve restores proper gas delivery and can stop intermittent heating issues. What it does:

• Opens and closes the gas supply to the oven/burner so burners ignite only when commanded
• Prevents uncontrolled gas flow when the appliance is off
• Common replacement when burners or oven fail to light or heat inconsistently
• Can address persistent clicking, weak flame, or failure to maintain temperature

• One safety valve

• Turn off the appliance power and gas supply before starting work
• Inspect and replace any damaged gaskets or fittings during installation
• Use proper tubing fittings and a leak test after reassembly; check for tight seals

This bake solenoid controls gas flow to the main oven's bake burner. When energized by the control, it opens the safety valve so the igniter can light the flame and the oven can heat and maintain your set temperature. What it does:

• Opens and closes gas flow to the bake burner during a call for heat
• Works with the igniter/flame-sensing system to light the bake flame
• Helps maintain set temperature by cycling gas flow during bake
• Typical symptoms of a failing solenoid: bake burner won't ignite, igniter glows with no flame, or the burner lights then shuts off

• One bake solenoid for the main oven

• Disconnect power and shut off the gas supply before servicing
• Access the oven valve/solenoid assembly per your unit's service manual
• Transfer electrical connectors one at a time; ensure proper orientation and secure fit
• After reassembly, restore gas and check all connections for leaks with a soap-and-water solution

This dual-type oven safety valve controls gas flow to the oven burners, restoring safe, reliable delivery of fuel for baking and broiling. Use it when the oven won't heat or gas flow needs proper regulation. What it does:

• Regulates and shuts off gas to the oven bake/broil circuits for safe operation
• Replaces a faulty valve that can cause no heat, intermittent ignition, or gas flow issues
• Works as the control point between the gas supply and oven burners to ensure proper fuel delivery
• Designed for direct replacement in compatible GE ovens

• One oven safety valve (dual type)

• Turn off gas supply and electrical power before starting any work
• Only connect fittings per manufacturer orientation; tighten and test all gas connections for leaks
• After installation, run a full ignition and leak test before normal use

This thermal cutoff is a temperature-sensing safety thermostat that helps prevent overheating by interrupting power when excessive heat is detected. Use it to restore proper safety protection in affected appliance heater or control circuits. What it does:

• Monitors temperature and opens the circuit if heat rises above the designed threshold
• Helps prevent overheating-related damage or fire risk in heating systems
• Stops power to heating elements when a fault causes unsafe temperatures
• Commonly used with ovens, dryers, and other heater-equipped appliances as a fail-safe

• One thermal cutoff

• Power must be disconnected before inspection or replacement to avoid shock or injury
• Handle the part carefully and observe wire connection orientation; replace with same type only
• If other components show heat damage, inspect the whole heating circuit and controls

A replacement safety valve kit that restores a safety shutoff component to appliances, helping stop flow when a fault is detected so the unit can operate safely. Fits compatible Frigidaire appliances that use this OEM kit. What it does

• Replaces the appliance's safety valve assembly to restore proper shutoff function
• Prevents continued fuel or water flow when a fault or unsafe condition occurs
• Commonly used when the appliance fails to start, fails to heat, or shows safety-related shutdowns
• Helps resolve intermittent operation or safety trip symptoms tied to a failed valve

• One safety valve kit (single complete replacement kit)

• Disconnect power and gas/water supply before starting any repair
• Follow the appliance's service manual or wiring diagram for correct routing and connections
• Use proper tools and safety gear;
• Test for leaks and proper operation after installation and before returning the appliance to service

This oven safety valve controls natural gas flow to the bake/broil burners so the oven heats reliably and shuts off gas when not called for. Replaces a worn or failed valve to restore safe oven operation. What it does:

• Opens and closes gas supply to the oven burners when heat is requested
• Prevents unwanted gas flow when the oven is off
• Common replacement for ovens that won't heat or have intermittent ignition
• Works with the oven's temperature control and safety systems

• One oven safety valve (natural gas)

• Turn off electrical power and shut off the gas supply before starting work
• After installation, check all gas connections for leaks with an approved leak detector and follow local codes

This water inlet valve controls water flow to the refrigerator's dispenser and ice-making system, restoring proper water delivery when the factory valve fails. Designed as a direct-replacement valve assembly for compatible Frigidaire units. What it does

• Opens and closes to allow water into the ice maker and door dispenser when signaled
• Prevents water flow when the dispenser or ice maker is inactive
• Common symptom: dispenser or ice maker does not dispense water or fills slowly
• Common symptom: water intermittently flows or the ice maker fails to fill

• Disconnect power and shut off the water supply before beginning work
• Drain remaining water from lines to limit spills during removal
• Replace mounting hardware and tubing fittings exactly as removed; use plumber's tape where appropriate on threaded connections
• Inspect connections and test for leaks after restoring power and water

This safety valve assembly controls the flow of gas to the oven or range burner, restoring safe operation and allowing the appliance to heat when the valve opens. It replaces a faulty shutoff/regulator valve to help address heating issues. What it does:

• Regulates and shuts off gas flow to the burner/oven when required for safe operation
• Commonly used when the oven or burner will not light or stays unlit
• Can stop gas flow if a valve or regulator fails, reducing risk of unregulated gas release
• Works with the appliance's ignition and safety systems to allow normal heating once operating correctly

• One safety valve assembly as shown

• Shut off gas supply and power before starting; follow appliance-specific safety procedures
• Only install on compatible models and use proper fittings; verify orientation and connections match the original
• Check all gas connections for leaks after installation using an approved leak-detection method