Range Valve

The Oven Safety Valve is an OEM replacement part for Frigidaire gas ranges. This valve controls gas flow to the oven burner.

Causes of a faulty oven safety valve can include wear of sealing surfaces due to prolonged heating and cooling during cooking cycles. Exposure to food or liquid residues over time may also affect valve function.

Symptoms of a bad oven safety valve include:

• The oven not heating up despite the igniter working correctly
• A smell of gas indicates a leak or uncontrolled release
• Inconsistent oven temperatures or heating patterns
• The oven failed to maintain the set temperature

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

This GE Oven Safety Valve is an OEM replacement part for GE ranges. The part's primary function is to prevent gas from releasing until the igniter has received enough voltage to ignite it safely. Not allowing any gas to exit before ignition helps avoid potential safety hazards from uncombusted gas.

Causes for failure could include wear and corrosion over many years of use. Repeated heating and cooling stresses may cause cracking or breaking in the valve's delicate regulating components. Mineral deposits or dirt buildup may also obstruct proper opening and closing.

Symptoms of a faulty safety valve would include:

• gas releasing or leaking even when the igniter is not lit
• the oven or burners not lighting at all when the valve is engaged

This GE OEM part is also compatible with Hotpoint, RCA and select Kenmore models.
 

This valve controls gas flow to a range/cooktop surface burner for smooth ignition and precise flame adjustment. Replacing a worn valve helps restore reliable burner lighting, accurate heat control, and safer shutoff.

• Regulates gas to a surface burner for ignition and flame size control
• Sticking or worn internal seals can cause hard-to-turn operation or gas odor
• Failure may prevent the burner from lighting or shutting off completely
• Inconsistent or unresponsive flame adjustment can indicate a failing valve

• Disconnect power and shut off the gas supply before servicing
• Allow the appliance to cool; access the valve/manifold per your model's instructions
• Mark and disconnect tubing and any wires; transfer fittings or a separate spark switch from the old valve if applicable
• After installation, restore gas and check all joints with an approved leak-detection solution; verify proper burner operation

This surface burner control valve regulates gas flow to a single cooktop or range burner, allowing smooth ignition and precise flame adjustment. Replace a worn or stiff valve to restore consistent, reliable burner control.

• Regulates gas from the manifold to an individual surface burner as the knob is turned
• Opens/closes the gas path to ignite and adjust flame height
• Helps maintain a steady flame at low and high settings
• Common symptoms: burner won't light or only lights with a match, flame won't adjust or is uneven, control knob hard to turn or seized, gas odor near the control area

• Disconnect power and shut off the gas supply before servicing
• Remove the knob and access panel to reach the valve; label and disconnect gas tube fittings
• Support the manifold with a second wrench when loosening/tightening fittings; do not overtighten
• After installation, restore gas and check all connections for leaks using a non-flammable leak-detection solution; verify proper ignition and flame adjustment

This gas valve control regulates the flow of gas to a burner in your range, enabling reliable ignition and precise flame adjustment. Replacing a worn valve restores smooth knob operation and consistent burner performance.

• Meters gas to a single burner as the control knob is turned
• Works with the ignition system to light and sustain the flame
• Typical symptoms include a burner that won't ignite or lights intermittently
• Flame will not adjust or is unstable; knob feels tight, sticky, or turns without proper control

• Disconnect electrical power and shut off the gas supply before servicing
• Allow the appliance to cool and work in a well-ventilated area
• Note the valve's orientation; transfer any model-specific fittings or hardware from the original valve as needed
• After reassembly, restore gas and check all connections with an approved leak-detection solution; verify proper ignition and flame control

Made by Frigidaire. This is a dual oven valve for bake and broil.

This surface burner gas valve regulates the flow of gas to the burner on your range or cooktop, enabling proper ignition and flame control. Replacing a worn valve restores safe operation and consistent flame performance.

• Meters gas to the burner in response to the control knob
• Supports reliable ignition and maintains a stable, adjustable flame
• Typical symptoms: burner won't light, flame won't adjust or goes out, knob stiff or difficult to turn
• Can help correct uneven heat on the affected burner

• Disconnect power and shut off the gas supply before servicing
• Allow the appliance to cool; remove panels as directed by your model's service information
• Note valve orientation; transfer any model-specific brackets or fittings from the old valve if required
• After reassembly, check all connections for leaks with a soap-and-water solution

This replacement part is a safety valve. This part is found in various types of refrigerators or freezers and is able to ensure that the appliance is running smoothly and safely during use. A new safety valve might be needed if the user notices that the current one is no longer working properly. This may include it having a leak or making unfamiliar sounds. The user should be able to access the back of the appliance to replace or repair this part.This is a genuine OEM replacement part made by Frigidaire, sold individually. The item, made of durable materials, is meant to last a long time.

This safety valve controls and shuts off gas flow to the appliance burner assembly to help prevent unintended gas delivery. It restores safe operation when a failed valve is replaced and the ignition system is working properly. What it does:

• Regulates and stops gas flow to the burner/oven when the valve is closed
• Prevents gas from reaching the burner when ignition is off or unsafe conditions occur
• Common symptom fixes: no heat, continuous clicking with no ignition, or a persistent gas smell when appliance is trying to light
• Works with the appliance's ignition and pressure systems to maintain safe fuel delivery

• Turn off gas and power at the appliance before starting work
• Use appropriate tools and follow the appliance service manual; fittings may require thread sealant rated for gas
• After installation, check all connections for leaks with a non-corrosive leak detector or soapy water; do not use an open flame

This control valve is an important safety feature found on many gas ranges. It's located inside the back of the range near the area where the buttons and controls are found. The reason the control valve is included in ovens is to prevent gas from moving to the burners if the igniter is not able to ignite the gas or there is no electricity. The control valve could be faulty if there is a smell of gas near the valve, the burner flame flickers, or the flame cannot be turned on high.In any of these situations, the control valve must be replaced. The repair is easy and takes only a few minutes. The bottom of the oven will need to be removed, which may require a screwdriver. After removing it, remove the flame spreader by taking out two screws and sliding it out of the oven. Remove the screw holding the oven burner tube and take it out to access the valve and replace it.This control valve is made to be compatible with RCA, Kenmore, Roper, General Electric, and Hotpoint ranges. It's sold as an individual OEM replacement part that is sourced directly from the manufacturer.

This water inlet valve controls the flow of water to the refrigerator's dispenser and icemaker, ensuring reliable water delivery for drinking and ice production. Replace a failing valve to restore normal water flow and prevent leaks. What it does:

• Opens and closes to supply water to the dispenser and icemaker when needed
• Stops water flow to help prevent continuous filling or flooding
• Commonly used when dispenser water is weak, icemaker won't fill, or there is leaking near the valve
• Matches OEM function and fit for compatible Frigidaire refrigerators

• One water inlet valve

• Shut off water and power to the appliance before starting any repair
• Handle water lines and electrical connectors carefully; replace worn gaskets or seals as needed

This genuine OEM part is an oven safety valve for gas ovens. The oven safety valve is designed to prevent gas from flowing to the burner assembly if the igniter is not hot enough to ignite the gas, or if no electricity is present. Over time, an oven safety valve can become inoperable due to excessive wear and tear. If the oven is no longer heating properly, not turning on, or no longer working as powerfully as it once did, the oven safety valve will need to be replaced.To replace this part, start by unplugging the oven and shutting off the gas supply. After that, move the range away from the wall. Use a wrench to unthread the nut to remove the gas supply tube from the safety valve. Next, open the oven door to gain access to the interior of the oven. Release the hinge locks that secure the door and pull the door off the oven. Remove the oven racks and proceed to unthread the screws that secure the oven's bottom panel. Once removed, locate the safety valve. Next, unthread the screw that holds the mounting bracket into place. Remove the old safety valve and align the new valve with its mounting bracket. Attach the wires to the safety valve terminals and reinstall the bottom panel and oven door.This replacement part is sold individually and is sourced directly from the manufacturer. It is compatible with General Electric, Hotpoint, and RCA brand ovens.

The Safety Valve Assembly is an OEM part for GE gas ranges. It automatically cuts off gas flow if excess pressure develops, providing critical safety protection.  

Symptoms of a faulty safety valve include:

• The range does not ignite and burners fail to light
• Gas leaks occur even when burners are off
• Responsiveness issues adjusting burner flames 

 Causes involve worn seals, dirt/debris blocking valve ports, or cracked componentry from shock over time.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This safety valve controls and shuts off the flow of gas to the appliance, helping the cooktop or oven heat safely and reliably. It replaces a failed valve to restore proper gas control and safe operation. What it does:

• Regulates gas flow to the appliance's burner assembly and/or pilot circuit
• Stops gas flow if the valve or control circuit fails, preventing unsafe leaks
• Common symptom: appliance won't heat or burners won't light despite power to the igniter
• Common symptom: intermittent heating or unit shuts off unexpectedly during operation

• One safety valve

• Turn off gas supply and disconnect power before servicing
• After installation, check all gas connections for leaks and verify proper ignition and shutoff operation
• Do not attempt repair if you smell gas; evacuate area.