Range Tube Or Fitting

1/4" gas supply tubing connects your range's gas line to the valve. Replace when damaged, cracked, leaking, or during valve service for safe operation.

This replacement fitting connects the appliance's water line to its internal plumbing so water flows where it's needed and stays sealed. It restores a proper watertight connection to help stop leaks and ensure reliable water delivery. What it does:

• Connects the external water supply line to the appliance's internal water inlet
• Creates a secure, watertight seal to prevent drips and leaks at the connection point
• Supports consistent water flow for ice makers, dispensers, or valves where used
• Can resolve symptoms like visible leaks, reduced water flow, or intermittent filling

• One replacement fitting

• Turn off the water supply and unplug the appliance before installing
• Inspect mating surfaces and replace any damaged O-rings or gaskets as needed
• Hand-tighten first, then snug with appropriate tools; avoid over-tightening
• If plumbing sealant is recommended by your installer, use plumber's tape on threaded connections only

Supplies gas from manifold to burner assembly. Replace if cracked, corroded, kinked, or leaking to restore safe fuel delivery to your gas range burners.

This is a gas tube assembly that connects the gas supply to the burner or oven components in a range. It ensures a secure, leak-free path for gas flow to the burners. Replace this tube if you detect a gas smell near the connections, notice inconsistent flame performance, or find visible damage or corrosion on the existing tube.

Vent tube that routes hot air and moisture from the oven cavity to the exterior. Replace if cracked, corroded, or disconnected to restore proper ventilation.

Upper oven vent tube for gas and electric ranges. Channels hot air from the oven cavity to the exterior vent. Replace if cracked, damaged, or missing.

Connects the pilot flame to the thermostat in gas ranges. Replace if tube is kinked, cracked, or damaged, preventing proper heat sensing and regulation.

This is an inverted flare nut with 3/8-24 UNF threading used on gas tubing connections in a range or oven. It creates a secure, leak-free seal where gas supply lines connect to the appliance. Replace this nut if it is stripped, cracked, or damaged, which can result in gas leaks or loose tubing fittings.

This gas tubing is the direct-fit replacement part that routes natural or liquid propane gas between range components, restoring safe fuel flow for proper burner operation. It replaces worn or damaged tubing without modifying factory connections. What it does:

• Carries gas from the valve to burners or manifold to enable ignition and normal burner flames
• Commonly replaced when tubing is corroded, cracked, kinked or leaking
• Can stop symptoms such as persistent gas smell, burner failure to light, or intermittent flame
• Matches OEM fit and connection locations for a straightforward swap

• One gas tubing

• Shut off the gas supply and disconnect power before starting any work
• Only install on compatible appliances; use approved fittings and follow torque specs from the appliance manufacturer
• Check all connections for leaks after installation using a soapy-water solution or approved gas leak detector

Gas supply tube for gas ranges. Connects gas valve to burner manifold. Replace if cracked, damaged, or leaking. Essential structural component.

Replace the left front burner tube on your range. Needed when the tube is cracked, corroded, or damaged, preventing proper gas flow to the burner head.

Burner tube assembly for gas ranges. Connects burner to gas supply valve. Replace if cracked, damaged, or leaking to restore safe operation.

This burner tube connects gas supply to your range burner assembly. Replace if cracked, corroded, or damaged to restore proper gas flow and prevent leaks.

Black burner tube for range cooktop. Replaces cracked, corroded, or damaged gas burner tubes. Installs between gas valve and burner assembly.

This tubing is the OEM thermo/safet capillary line used with the temperature sensing/thermal safety assembly. It transfers temperature information to the control so the appliance can maintain proper temperature and protect components. What it does

• Carries temperature feedback from the sensing bulb to the thermostat/thermal safety device
• Allows the control to react to temperature changes and open/close circuits as designed
• A damaged or kinked tube can cause inaccurate temperature sensing or control faults
• Common symptom: temperature not regulated or unit cycling irregularly when sensing line is compromised

• One thermo/safet tubing

• Install only if tubing and fittings match the original; avoid sharp bends or kinks in the line
• Handle the sensing bulb and capillary gently to prevent damage
• Disconnect power before attempting service; follow all safety and grounding procedures