Range Tube Or Fitting

This fitting tube connects a section of appliance tubing to the service plumbing to restore a sealed fluid path and prevent leaks. It's a direct-replacement plumbing fitting used where small-diameter tubing joins a fixed port. What it does

• Forms a secure connection between tubing and a plumbing port to maintain water/condensate flow
• Stops symptoms like visible leaks, pooling water, or reduced fill/drain performance when the original fitting is damaged
• Provides the proper interface for OEM tubing size and routing in the appliance
• Helps restore normal operation without altering factory plumbing

• One fitting tube

• Disconnect power and shut off water supply before servicing
• Drain remaining water from lines to reduce mess and pressure before removing old fitting
• Hand-start fittings then tighten to OEM torque; avoid over-tightening which can crack ports or tubing
• Inspect connections for leaks after restoring water and power; re-tighten if needed

This metal gas tubing connects the appliance's gas supply components to deliver fuel safely to burners or the oven. It restores proper fuel routing for reliable ignition and consistent burner performance. What it does:

• Provides a sealed pathway for natural gas or LP from the valve to the manifold or burner assembly
• Restores proper gas flow when tubing is cracked, corroded, or visibly damaged
• Helps stop symptoms such as gas odor near the appliance, weak or no burner ignition, or inconsistent flame
• Designed to match OEM shape and fittings for a correct fit and secure connection

• Turn off the gas supply and electricity to the appliance before starting work
• Only install where tubing and fittings match the original; use correct flare/nipple fittings as required
• Tighten connections per manufacturer guidance; check all joints with a soap solution or approved leak detector (do not use an open flame)

This gas tubing is the direct-fit replacement part that routes natural or liquid propane gas between range components, restoring safe fuel flow for proper burner operation. It replaces worn or damaged tubing without modifying factory connections. What it does:

• Carries gas from the valve to burners or manifold to enable ignition and normal burner flames
• Commonly replaced when tubing is corroded, cracked, kinked or leaking
• Can stop symptoms such as persistent gas smell, burner failure to light, or intermittent flame
• Matches OEM fit and connection locations for a straightforward swap

• One gas tubing

• Shut off the gas supply and disconnect power before starting any work
• Only install on compatible appliances; use approved fittings and follow torque specs from the appliance manufacturer
• Check all connections for leaks after installation using a soapy-water solution or approved gas leak detector

This tubing is the OEM thermo/safet capillary line used with the temperature sensing/thermal safety assembly. It transfers temperature information to the control so the appliance can maintain proper temperature and protect components. What it does

• Carries temperature feedback from the sensing bulb to the thermostat/thermal safety device
• Allows the control to react to temperature changes and open/close circuits as designed
• A damaged or kinked tube can cause inaccurate temperature sensing or control faults
• Common symptom: temperature not regulated or unit cycling irregularly when sensing line is compromised

• One thermo/safet tubing

• Install only if tubing and fittings match the original; avoid sharp bends or kinks in the line
• Handle the sensing bulb and capillary gently to prevent damage
• Disconnect power before attempting service; follow all safety and grounding procedures

This 7/16 replacement tube routes water inside the refrigerator to the ice maker or dispenser, restoring proper water flow and preventing leaks. It's a direct-fit replacement when the original tube is cracked, split, or clogged. What it does

• Carries water from the valve to the ice maker or dispenser line
• Replaces damaged, cracked, or kinked tubing that causes leaks
• Restores proper water flow when the dispenser or ice maker is starved or slow
• Helps stop visible water pooling or dripping inside the refrigerator

• One 7/16 replacement tube

• Turn off water supply and unplug the appliance before starting any work
• Confirm routing and secure connections match the original tube to avoid kinks
• Use proper fittings and a firm push or clamp connection; replace any damaged clips or seals

This right rear burner tube assembly routes gas to the right-rear cooktop burner so the burner lights and produces a steady flame. It restores correct gas flow to the right-rear burner on compatible ranges. What it does:

• Directs gas from the manifold to the right-rear burner for ignition
• Helps maintain an even, stable flame at the right-rear cooktop location
• Commonly replaced when the right-rear burner fails to light or has an irregular flame pattern
• Designed to fit as a single complete tube assembly for the right-rear burner

• Turn off gas supply and electrical power to the range before starting any work.
• Use caution when removing and installing gas components; replace gaskets or seals as needed.
• After installation, check all connections for leaks using a soap solution or a leak detector.

This tubing assembly routes water inside the appliance to maintain proper flow and sealing where factory tubing is required. It replaces damaged or leaking tubing to restore normal water routing and prevent leaks. What it does:

• Replaces worn, cracked, or pinched tubing that can cause leaks or reduced water flow
• Restores proper internal water routing to dispensers/valves or drain lines
• Helps stop visible water on the floor or pooling near appliance bases
• Maintains secure connections where the original tubing was installed

• Turn off power to the appliance and shut off the water supply before servicing
• Inspect connection fittings and clamps; replace any damaged clips or seals
• Avoid sharp bends or kinks when routing the tubing; secure with existing brackets