Refrigerator Handle

The Fridge Handle is an OEM part for Whirlpool refrigerators. This handle is essential for opening and closing the refrigerator door, providing a sturdy and comfortable grip. The handle measures 20 inches in length. Please note that this item does not come with screws for installation. This means you may need to use the existing screws or obtain suitable replacements separately.

You should replace the fridge handle if it becomes damaged or loose. Causes of a bad handle can include wear and tear from regular use, accidental impacts that cause cracks or breaks, or the loosening of attachment screws over time. A compromised handle can make it difficult to open the refrigerator door and may even pose a safety risk.

Symptoms of a bad Fridge Handle include:

• The handle feeling loose or wobbly
• Cracks or breaks in the handle
• Difficulty in opening or closing the refrigerator door
• The handle detaching from the door

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Color: Stainless.

This is a refrigerator door handle that lets you easily open and close the door while providing a clean, finished look. Replacing a worn or broken handle restores proper grip and appearance.

• Provides a secure grip to open/close the refrigerator door
• Common fix for a loose, cracked, or broken handle
• Restores original appearance when the handle is scuffed or yellowed

• Unplug the appliance before beginning
• Use the correct driver to avoid stripping screws
• Support the handle as you remove/install screws to prevent misalignment
• Do not overtighten; align handle to door trim before final snugging

Restore a solid, comfortable grip on your freezer door with this black Freezer Door Handle. It replaces a damaged or worn handle to bring back dependable daily use and a clean, factory look.

• Provides a sturdy handhold for opening and closing the freezer door
• Direct replacement for a cracked, broken, loose, or missing handle
• Refreshes the appliance's appearance if the old handle is scuffed or discolored
• Installs on the existing mounting points for your model

• Unplug the appliance and secure the door before service.
• Access and loosen the handle's set screws or mounting screws, then remove the old handle.
• Position the new handle; transfer and tighten existing fasteners evenly—do not overtighten.
• Verify smooth door operation and alignment after installation.

This replacement block is a small structural component used inside the refrigerator to locate, support, or align its mating parts. Replacing a worn or broken block restores proper fit and helps keep the affected assembly secure. What it does:

• Provides a stable mounting/locating point for the applicable assembly
• Helps maintain alignment and reduces wobble or looseness
• Common failure signs: cracks, missing piece, or stripped fastener hole
• Symptoms may include rattling, sagging, or parts that won't stay in place

• 1 block

• Unplug the refrigerator before servicing; wear cut-resistant gloves
• Remove items and any obstructing parts to access the block; note orientation for reassembly
• Transfer any reusable hardware from the old block and secure the new block without overtightening
• Restore power and verify proper fit and operation of the serviced area

Color: Stainless

Color: Stainless
The Handle is an OEM part for Whirlpool refrigerators. This handle attaches to refrigerator doors, allowing for intuitive opening and closing.

Causes of a bad handle can include wear from frequent use over multiple years, damage from excessive force or impacts, or deterioration of mounting brackets and fasteners.

Symptoms of an issue with the handle include:

• Loose, unstable or wobbly handle movement
• Difficulty opening/closing the refrigerator door
• Discomfort gripping the handle during use
• Visible cracks, breaks or detachment from the door

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This freezer door handle restores a secure, comfortable grip on your refrigerator's freezer door. Replace it when the original is cracked, loose, or missing to maintain safe operation, clean appearance, and easy everyday access.

• Provides the handhold used to open and close the freezer door
• Attaches to the door's existing mounting points/fasteners for a secure fit
• Helps resolve issues such as a broken, cracked, or wobbly handle
• Can improve ease of opening if the old handle has failed

• Disconnect power before servicing; wear cut-resistant gloves
• Support the old handle, then loosen/remove its fasteners; note their placement
• Position the new handle on the existing mounts and tighten fasteners evenly
• Do not overtighten; verify alignment and that the handle is secure

Replace a worn, loose, or broken refrigerator door handle with this complete handle assembly. It restores a secure, comfortable grip so you can open and close the refrigerator door easily while maintaining the unit's original look. What it does:

• Attaches to the refrigerator door to provide a sturdy handhold
• Replaces cracked, broken, or missing handles
• Helps correct a loose or wobbly handle that won't stay secure
• Restores the factory appearance of the door

• 1 refrigerator door handle assembly

• Disconnect power and protect the door surface with tape or a cloth before starting
• Remove any trim/caps as needed and loosen the hidden set screws or mounting bolts on the old handle
• Position the new handle, then tighten fasteners evenly—do not overtighten
• Reinstall any caps/trim and ensure the handle is secure

This door handle provides a sturdy, comfortable grip for opening and closing the appliance. Replace a cracked, loose, or missing handle to restore safe operation and refresh the appearance of your kitchen or laundry equipment.

• Provides the handhold needed to open and close the appliance door or drawer
• Transfers pulling force to the door without stressing the latch or hinges
• Restores usability and appearance when the original handle is damaged or worn
• Common symptoms: cracked or broken handle, looseness, missing handle, difficulty opening the door

• Disconnect power before servicing; allow hot surfaces to cool if applicable
• Protect surrounding finishes; support the door or drawer to reduce strain while removing/installing the handle
• Refer to your model's parts diagram for fastener type and location; reuse model-specific screws/caps if applicable
• Align the handle and tighten fasteners evenly—do not overtighten

Color: Stainless

The Handle is an OEM component specifically designed for Whirlpool refrigerators. It provides easy access and convenient opening of the refrigerator door.

Symptoms of a bad handle include: 

• Difficulty or instability when opening the refrigerator door
• Looseness, wobbling or detachment from the door 
• Cracks or breaks that compromise safety and function

Causes can include normal wear and tear over prolonged use, excessive force, or damage from falls or impact. 

This OEM Whirlpool replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Handle is an OEM part for Whirlpool refrigerators. It allows for easy opening and closing of the freezer door. This handle is designed to provide a sturdy grip, making it convenient to access your food items.

A bad handle can be caused by wear and tear over time, excessive force applied to the handle, or damage due to accidental impact or mishandling.

Symptoms of a bad drawer handle include:

• Difficulty in opening or closing the door.
• Loose or wobbly handle.
• Cracks or breaks in the handle.

Replace your worn-out or damaged handle with this OEM part and restore your refrigerator. 

This Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
 

Restore a solid, comfortable grip on your refrigerator door with this face-mount door handle assembly. It replaces a worn, cracked, or loose handle so the door opens and closes smoothly and looks refreshed.

• Provides the front-mounted pull used to open and close the door
• Face-mount design secures from the front of the door panel
• Common symptoms: broken or cracked handle, loose/wobbly handle, missing handle, cosmetic damage
• Restores proper leverage and everyday usability

• Disconnect power for safety before servicing
• Remove the existing handle and any trim caps; note screw locations
• Position the new handle and fasten evenly; avoid overtightening
• Transfer original mounting hardware if needed and the door seals and operates properly

This genuine replacement door handle restores a solid, comfortable grip for opening and closing your appliance's door. Replace a cracked, loose, or missing handle to keep daily use safe and the appliance looking factory-clean. What it does:

• Provides the handhold needed to open and close the door
• Transfers pull force to the door without stressing the latch
• Helps ensure the door can be operated safely and consistently
• Common symptoms: handle cracked, broken, loose, spinning, or missing

• 1 door handle

• Disconnect power before servicing; allow hot surfaces to cool
• Protect surrounding surfaces; support the door if required by your model
• Access the mounting screws as directed by your service manual; note screw locations and any spacers
• Tighten screws evenly without overtightening; wear cut-resistant gloves

Replace a cracked or loose handle with this handle assembly to restore a solid, comfortable grip when opening and closing your appliance. It helps keep daily use easy while refreshing the unit's appearance. What it does:

• Provides the handhold used to open and close the door or lid
• Restores usability when the original handle is cracked, loose, or missing
• Helps correct issues like wobbling, broken mounting points, or the handle pulling free
• Improves ergonomics and appearance versus a damaged or worn handle

• One handle assembly

• Disconnect power before beginning work; wear cut-resistant gloves
• Remove the existing handle and retain any model-specific screws or trim for reuse
• Align the new handle with existing mounting holes and tighten screws snugly—do not overtighten
• Verify smooth door/lid operation and secure fit after installation

This refrigerator door handle restores a solid, comfortable grip for opening and closing the door. Replace a cracked or loose handle to improve everyday use and keep your appliance looking and functioning like new.

• Provides the handhold used to open and close the refrigerator or freezer door
• Secures to the door using the factory mounting points for a stable fit
• Replaces cracked, broken, or scuffed handles
• Addresses a loose, wobbly, or missing handle that won't stay attached

• Disconnect power to the appliance before servicing
• Protect the door finish with tape or a cloth around the work area
• Use the correct driver (Allen/hex/Torx per model) to remove and install fasteners
• Align the handle with the mounts and tighten screws evenly—do not overtighten