Refrigerator Relay, Overload, Capacitor

This start relay controls power to the compressor's start winding so the refrigerator can start and run. Replacing a weak or burned relay restores dependable compressor start-up and can stop repeated clicking with warming temperatures.

• Energizes the compressor's start winding to provide initial torque, then disengages from the circuit
• Common failure symptoms: refrigerator not cooling or intermittently warm; compressor hums/clicks and won't start; relay rattles, smells burnt, or shows heat damage; overload trips
• Helps prevent hard-start conditions that stress the compressor
• The relay contacts are open/shorted, the compressor may fail to start and cycle off on overload

• Disconnect power before servicing; wear appropriate PPE
• Access the rear machine compartment; remove the relay cover on the compressor. Note wire positions, pull the old relay straight off the compressor pins, transfer wires, and fully seat the new relay in the same orientation
• If equipped, safely discharge the run capacitor; inspect the overload, wiring, and terminals for heat damage and address as needed
• Reinstall the cover. If the compressor still won't start, further diagnosis of the start device, capacitor, or compressor is required

This refrigerator compressor starter is the start device that plugs onto the compressor terminals. It briefly energizes the start winding so the compressor can start reliably, helping restore cooling when the original starter fails. What it does:

• Engages and then disengages the compressor's start winding during startup
• Mounts directly on the compressor pins under the terminal cover
• Common symptoms of a failed starter: not cooling, rapid clicking/humming from the compressor area, compressor hot but not running, or intermittent starts
• Replaces the original start device specified in your model's parts diagram

• 1 compressor starter

• Disconnect power before servicing; pull the unit out to access the back panel
• Remove the compressor terminal cover; note/photograph wire positions and orientation
• Pull off the old starter; inspect the overload and wiring for heat damage
• Align with the compressor pins and press on firmly; reinstall the cover and restore power

PTC relay is a start device that helps the appliance motor begin turning by providing a brief boost to the start winding. Replacing a faulty relay restores reliable motor starting and can return normal operation. What it does:

• Provides a temporary start assist to the motor's start winding so the motor can overcome initial inertia.
• Commonly replaced when the motor hums but won't start or when the unit fails to begin operation.
• Can address symptoms such as clicking noises at startup, intermittent motor starting, or no motor movement despite power.
• Works as the motor start control — failure can prevent the appliance from operating properly.

• Disconnect power before servicing to avoid electric shock.
• Note terminal locations and orientation before removal; install replacement on the same terminals.
• Handle terminals gently and ensure tight, corrosion-free connections.
• After installation, restore power and verify the motor starts and runs normally.

This overload relay protects and helps start the refrigerator/freezer compressor by cutting power if the motor overheats or draws excessive current. Replaces a failed relay to restore normal compressor start and protect the compressor from damage. What it does:

• Senses excessive compressor current or heat and interrupts power to prevent motor damage
• Works with the compressor start device to help the compressor start reliably
• Commonly replaces a failed relay when the compressor hums but won't start or the refrigerator is not cooling
• Helps prevent repeated compressor attempts that can trip breakers or overheat wiring

• Disconnect power to the appliance before accessing electrical components
• Handle terminals carefully; ensure correct seating on the compressor motor pins
• Only install parts that match the appliance's service literature and wiring configuration

A thermal overload protector that helps prevent motor damage by cutting power if the dryer motor overheats. Fits the motor assembly and restores normal operation once the motor cools. What it does:

• Detects excessive motor temperature and interrupts power to prevent motor burnout
• Helps stop the motor from running when overheating occurs
• Commonly replaced when the dryer won't start or the motor hums but does not turn
• Can prevent further electrical damage by opening the circuit during thermal faults

• One thermal overload protector

• Disconnect power to the appliance before servicing to avoid shock or injury
• Located on or near the dryer motor; note wire locations or take a photo before removal
• Replace with the correct PN and secure terminals firmly; do not force connections
• Check motor bearings, start components, and wiring if symptoms continue after replacement

A replacement motor start/run capacitor that helps restore reliable motor starting and smooth operation for compressors and fans. Installing the correct capacitor can reduce hard-starts, humming and intermittent motor operation. What it does:

• Provides the temporary boost motors need to start and stabilize while running.
• Helps compressors and fan motors start more easily and run more efficiently.
• Commonly associated with symptoms like humming, motors that won't start, intermittent operation, or reduced cooling performance.
• Prevents repeated motor stress that can lead to overload trips or premature motor wear.

• Disconnect power to the appliance before accessing electrical components.
• Discharge the capacitor and tag/photograph wire locations before removal to ensure correct reinstallation.
• Replace with the exact OEM part or an approved equivalent; do not bend or puncture the capacitor can.

This refrigerator compressor start device provides the initial boost the compressor needs to start, then disengages. Replacing a failed start device helps restore reliable compressor startup and steady cooling performance.

• Supplies momentary power to the compressor's start winding to get the motor running
• Disengages after startup so the compressor can run normally
• Typical failure symptoms: refrigerator warm or not cooling, compressor won't start, rapid clicking from the compressor area, or intermittent cooling
• Located on the side of the compressor at the back of the appliance

• Unplug the refrigerator and allow the compressor area to cool before servicing
• Access the compressor at the rear; note wire positions and the device orientation
• Pull the old device straight off the compressor pins; seat the new device fully and reconnect wires securely
• If your model uses a separate run capacitor, transfer and reconnect it exactly as originally configured

This relay assembly helps start the refrigerator compressor so the cooling system can run reliably. It replaces a worn or failed start relay to restore normal compressor startup and reduce hard-start symptoms. What it does:

• Provides the initial start pulse to the compressor motor so the refrigeration cycle can begin
• Stops excessive current draw during startup to protect the compressor
• Commonly used when the compressor hums, won't start, or cycles on and off rapidly
• Helps eliminate starter-related clicking or failure-to-start issues

• Disconnect power to the appliance before inspecting or replacing the relay
• Handle electrical connectors carefully; ensure secure, correct reattachment
• Verify match to the existing relay and mounting before installation

This motor overload (thermal protector) helps protect the washer motor from overheating and motor damage by interrupting power if the motor draws excessive current or gets too hot. It's a simple, compact safety device that restores normal operation once cooled. What it does:

• Senses excessive motor temperature/current and cuts power to prevent motor burnout
• Helps stop motor humming or stalling caused by overload conditions
• Can prevent intermittent starts or trips when the motor overheats
• Resets automatically after the motor cools (depending on motor design)

• Disconnect power to the appliance before starting any repair
• Mounts onto the motor or motor harness per the OEM location; replace the faulty unit like-for-like
• Use basic hand tools; avoid tugging on wires—disconnect connectors carefully

This overload is a compressor protector that helps stop the compressor from overheating or drawing excessive current, keeping the refrigeration system safer and helping prevent premature compressor failure. What it does:

• Opens the compressor circuit when the compressor overheats or draws excessive current
• Helps protect the compressor motor from damage caused by electrical overloads or locked-rotor conditions
• Works with the start device/relay to allow normal compressor starting and operation
• Commonly used when a compressor fails to start, hums, or trips the circuit

• One overload protector

• Disconnect power to the appliance before attempting service
• Handle the part carefully and avoid bending terminals; secure it per OEM mounting method
• If compressor or start components show damage, inspect/replace those parts as well; consider service for sealed-system diagnosis

This compressor start relay helps the refrigerator compressor start reliably, restoring proper cooling performance when the compressor fails to start. Designed to replace the factory start device on compatible Frigidaire compressors. What it does

• Provides the initial boost/current path to spin the compressor motor during startup
• Commonly replaced when the compressor hums but will not start or cooling is intermittent
• Helps prevent repeated hard starts that can overload the compressor
• Works with the compressor's overload to enable normal run operation once started

• One compressor start relay

• Disconnect power to the appliance before servicing to avoid electric shock
• Access compressor terminals at the rear base or service panel per your model's service instructions
• Remove and replace only the relay (verify terminals match and clip securely); do not attempt repairs on the sealed compressor
• If compressor still won't start after replacing the relay, further diagnosis of the compressor, overload, or controls is recommended

This replacement screw fastens appliance panels and trim to restore secure fit and reduce rattling or movement. Use it when a missing or damaged screw is causing loose parts or noisy operation. What it does:

• Secures panels, trim, or internal components to maintain proper alignment and stability.
• Stops rattling or vibration caused by loose or missing hardware.
• Helps prevent gaps that can catch on clothing or obstruct doors/drawers.
• Small hardware solution for common fit and finish issues.

• Disconnect power and any water supply before starting work.
• Use the correct screwdriver or driver bit to avoid stripping the head.
• Keep track of small parts and work on a stable surface; magnetic trays help.

The Refrigerator Main Switch Assembly is an essential component designed to maintain the optimal performance of your Samsung refrigerator. This genuine OEM part ensures a perfect fit and reliable operation, seamlessly integrating with your applianceGÇÖs existing systems. The main switch assembly controls the power distribution within the refrigerator, allowing you to efficiently manage cooling cycles and maintain consistent temperatures. By replacing a faulty main switch with this high-quality assembly, you can restore your refrigeratorGÇÖs functionality and extend its lifespan. Installation is straightforward, making it an ideal choice for DIY repairs and saving you the cost of professional service. Using a genuine OEM part guarantees compatibility and durability, providing peace of mind that your refrigerator will continue to operate smoothly. Enhance the reliability and efficiency of your Samsung refrigerator with the Refrigerator Main Switch Assembly , ensuring your appliance remains a dependable part of your kitchen.

This capacitor stores and releases electrical energy to help the refrigerator's compressor start and run smoothly. Replacing a weak or failed capacitor can restore reliable compressor startup and more consistent cooling performance.

• Provides the electrical boost/phase shift needed for compressor motor startup and steady operation
• Works with the start device to deliver proper current to the compressor
• Failure symptoms can include clicking or humming near the compressor, poor cooling, or short cycling
• May cause the compressor not to start after power interruptions when weak or failed

• Disconnect power before servicing any electrical component
• Safely discharge the capacitor before handling; avoid touching terminals
• Note wire positions and terminal markings; transfer leads one at a time to the matching terminals
• Secure the capacitor in its mounting/bracket to prevent vibration damage