Refrigerator Drawer, Shelf, Pan

This left-hand freezer slide assembly supports and guides the freezer drawer or basket so it opens and closes smoothly and stays aligned. Replacing a worn slide restores proper movement and helps ensure the drawer seals correctly.

• Supports the freezer drawer/basket on the left side
• Provides smooth sliding action for opening and closing
• Maintains alignment to help the freezer drawer seal properly
• Replaces a bent, damaged, or seized slide
• Symptoms include: hard-to-open/close drawer, binding or grinding, misalignment, or the drawer coming off track

• Disconnect power and remove contents from the freezer drawer
• Pull out and lift the drawer/basket to remove it from the slides
• Remove screws securing the left slide, position the new slide, and secure with existing hardware
• Reinstall the drawer/basket and check for smooth, even operation and proper closure

This slide rail assembly mounts beneath the fresh-food shelf to guide and support the deli/snack drawer, helping it open and close smoothly. Replace a cracked or worn slide to stop sticking, tilting, or the drawer dropping off its track.

• Supports and aligns the deli/snack drawer under the fresh-food shelf
• Provides smooth sliding action along the track
• Helps keep the drawer level and properly seated
• Common symptoms: drawer sticks, sags, falls off, or the rail is visibly cracked/broken

• Disconnect power; remove the drawer and clear the shelf area
• Remove screws or clips securing the old slide; note its orientation
• Install the new slide and transfer any reusable hardware if needed
• Reinstall the shelf and drawer; verify smooth travel before loading

This replacement bracket provides a secure mounting point for a designated component in your appliance. It keeps parts properly supported and aligned, helping the unit operate smoothly without vibration or shifting.

• Supports and anchors a specific part or assembly in the correct position
• Helps prevent vibration, rattling, and premature wear from movement
• Maintains alignment for consistent, reliable operation
• Replace if bent, cracked, or missing; symptoms can include loose components or unusual noise

• Disconnect power; shut off water or gas supply if applicable
• Access the bracket location per your model's service information and note the original orientation
• Transfer any screws, clips, or grommets from the old bracket to the new one
• Tighten fasteners evenly and verify alignment before restoring power

This refrigerator crisper pan replaces a damaged or missing produce drawer, restoring smooth operation and organized produce storage. It fits the factory rails beneath the crisper cover to keep fruits and vegetables contained and easy to access. What it does:

• Holds and organizes produce in the fresh food compartment
• Slides on the existing drawer rails under the crisper cover
• Restores function when the original pan is cracked, warped, or missing
• Common symptoms: broken corners, difficulty sliding, or the drawer coming off its tracks

• Empty the old drawer; pull straight out and lift to clear the stops
• Align the new pan with the slides and push in evenly—do not force
• If your model uses reusable trim/inserts on this drawer, transfer them from the original
• Handle any glass shelves and cold plastic carefully to avoid damage

This mounting cup installs in the freezer liner to create a secure attachment point for the ice maker or its bracket. It helps keep the assembly stable and properly aligned so the ice maker mounts firmly and operates reliably. What it does:

• Provides the receiving anchor for the ice maker/bracket mounting screw
• Helps hold the ice maker level and reduces movement or vibration
• A worn, stripped, or missing cup can prevent the screw from tightening
• Common signs include a loose or sagging ice maker, rattling, or difficulty keeping the ice maker aligned

• 1 mounting cup

• Disconnect power and shut off the water supply before servicing
• Remove the ice maker to access the cup location
• Seat the cup fully into the liner opening, then reinstall the bracket/ice maker and mounting screw
• Do not overtighten; verify the ice maker sits level and clears the fill tube

This rail guide assembly supports and guides a refrigerator or freezer drawer for smooth, stable opening and closing. It restores proper drawer alignment and helps prevent binding or accidental removal. What it does:

• Provides a track and guide for the drawer to slide in and out smoothly
• Keeps the drawer aligned to prevent sticking, jamming, or uneven movement
• Helps prevent the drawer from falling out when fully extended
• Restores normal drawer operation when original guide is cracked, worn, or broken

• One rail guide assembly

• Basic hand tools required; remove drawer to access mounting points before replacing guide
• Compare new part to the old part for orientation and matching mounting locations
• Do not force parts; ensure clips or screws are fully engaged to secure the guide
• Disconnect power only if required to remove interior components; follow appliance-specific safety instructions

Color: white. Measures about 2/3 of an inch wide by 1/2 an inch deep.

This holder rail secures and supports internal components in select LG appliances, restoring proper alignment and reducing movement or vibration. Replace a cracked, broken or worn rail to help stop rattling and improper component fit. What it does:

• Provides a stable mounting/support surface for internal parts that rely on the rail for alignment.
• Prevents shifting or vibration that can cause noise, wear, or misalignment.
• Install a new rail if the original is cracked, broken, warped or missing.
• Helps restore correct component positioning for reliable operation.

• Disconnect power and unplug the appliance before beginning any repair.
• Basic hand tools may be required; refer to the exploded parts list for disassembly steps.
• Inspect surrounding mounting points and fasteners; replace any damaged clips or screws.

This right-hand side adapter bracket secures the appliance cabinet or panel, restoring proper fit and stability. Replacing a damaged or missing bracket helps stop loose or misaligned panels and reduces rattling. What it does:

• Secures the right-side cabinet or panel to the chassis to maintain alignment and support.
• Helps eliminate panel movement, vibration and rattling that result from a cracked or missing bracket.
• Restores correct panel gaps so doors or drawers operate and close properly.

• Disconnect power (unplug or shut off breaker) before accessing the appliance.
• Remove the required access panels to reach the bracket; keep and reuse existing fasteners unless new hardware is specified by the model diagram.
• Transfer the bracket into position and fasten securely; check for proper panel alignment after installation.

Right hand side

Slide liner for refrigerator drawers that supports smooth, protected movement and helps keep contents from catching on the drawer track. Replaces worn or damaged liners to restore correct drawer travel and reduce noise. What it does:

• Provides a low-friction surface so the drawer slides smoothly and evenly.
• Protects the drawer edge and track from wear, cracking, or catching.
• Helps reduce sticking, grinding, or squeaking during drawer operation.
• Restores proper alignment when a liner is torn, warped, or missing.

• Remove drawer and contents before installing; handle glass or fragile parts carefully.
• Clean the track and mating surfaces before fitting the new liner.
• Press or slide the liner into place until it seats fully; no special tools are typically required.
• If mounting clips or tracks are damaged, replace those parts to ensure a secure fit.

This slide replaces a worn or broken drawer slide to restore smooth, secure drawer movement and proper alignment. It lets the drawer open and close reliably, improving access and preventing jams or sagging. What it does

• Guides and supports the drawer for smooth in-and-out movement
• Replaces a bent, worn, or broken slide that causes sticking or uneven travel
• Helps prevent the drawer from catching, binding, or dropping out of its track
• Restores proper drawer alignment and load-bearing stability

• Slide (single)

• Disconnect power to the appliance before servicing to avoid shock or injury
• Remove contents and the drawer per the appliance manual before replacing the slide
• Use common hand tools; retain all fasteners and match orientation to the old slide during install

This is a genuine replacement shelf support that is designed for use in select freezers and refrigerators. The metal shelf support is installed on the side or back wall of the fridge or freezer unit and holds the shelf in place. It is made of durable metal, but it can become bent or otherwise damaged. In some cases, it may become detached and lost, which would also require a replacement. It's important to get an OEM part like this to ensure an identical fit. This OEM shelf support is manufactured to exact specifications by Frigidaire and can be used in select models from the brand, as well as those from Kelvinator and Gibson. This shelf support can have several applications on various models so it will be important to check the owner's manual parts diagram before installing this part. This genuine support is sold individually. Additional parts and hardware will require an additional purchase. Always wear gloves when performing appliance repairs, even when replacing accessories like this, to protect the hands.

This left-side adapter secures the appliance's panel components and helps maintain proper alignment for reliable operation. It's a direct replacement that restores fit and support where the original left-side adapter is damaged or missing. What it does:

• Replaces a worn or broken left-side adapter/bracket to restore panel alignment and support
• Helps prevent rattling, misalignment, or loose panels that can occur with a damaged adapter
• Fits the left side mounting points to secure adjacent panels and components
• Works as a structural support piece in the appliance's chassis assembly

• 1 left-side adapter

• Disconnect power and water before starting any repair
• Handle panels carefully to avoid bending; support panels while removing fasteners
• Use the original fasteners unless replacements are specified by the manufacturer

Freezer basket slide for the upper basket. This rail supports and guides the top freezer basket so it glides in and out smoothly. Replace a cracked or warped slide to restore proper movement and alignment.

• Supports and tracks the upper freezer basket along the cabinet wall
• Provides smooth sliding action for easier access to frozen items
• Replace when the slide is cracked, broken, or deformed
• Typical symptoms: basket binds or tilts, scrapes, pops out, or won't close fully

• Disconnect power to the refrigerator before servicing
• Remove the upper basket; release locking tabs or screws and lift out the damaged slide
• Position and secure the new slide as shown in your model's diagram; do not overtighten screws
• Reinstall the basket and verify smooth travel and proper door sealing

This support mounts to the freezer wall and holds the upper basket in place. Replace a broken or missing support to restore proper alignment and smooth in-out movement of the basket and prevent sagging or jams.

• Provides side support for the upper freezer basket
• Keeps the basket level and aligned for easy access
• Replaces cracked or missing support that can cause the basket to drop, bind, or jam
• Helps eliminate wobble and uneven sliding when opening/closing

• Disconnect power to the refrigerator before servicing
• Empty and remove the upper freezer basket
• Release retaining tab(s) or remove fastener(s) and note the support's orientation
• Secure the new support, reinstall the basket, and verify smooth operation