Refrigerator Drawer, Shelf, Pan

This replacement bracket provides a secure mounting point for a designated component in your appliance. It keeps parts properly supported and aligned, helping the unit operate smoothly without vibration or shifting.

• Supports and anchors a specific part or assembly in the correct position
• Helps prevent vibration, rattling, and premature wear from movement
• Maintains alignment for consistent, reliable operation
• Replace if bent, cracked, or missing; symptoms can include loose components or unusual noise

• Disconnect power; shut off water or gas supply if applicable
• Access the bracket location per your model's service information and note the original orientation
• Transfer any screws, clips, or grommets from the old bracket to the new one
• Tighten fasteners evenly and verify alignment before restoring power

This refrigerator crisper pan replaces a damaged or missing produce drawer, restoring smooth operation and organized produce storage. It fits the factory rails beneath the crisper cover to keep fruits and vegetables contained and easy to access. What it does:

• Holds and organizes produce in the fresh food compartment
• Slides on the existing drawer rails under the crisper cover
• Restores function when the original pan is cracked, warped, or missing
• Common symptoms: broken corners, difficulty sliding, or the drawer coming off its tracks

• Empty the old drawer; pull straight out and lift to clear the stops
• Align the new pan with the slides and push in evenly—do not force
• If your model uses reusable trim/inserts on this drawer, transfer them from the original
• Handle any glass shelves and cold plastic carefully to avoid damage

Slide liner for refrigerator drawers that supports smooth, protected movement and helps keep contents from catching on the drawer track. Replaces worn or damaged liners to restore correct drawer travel and reduce noise. What it does:

• Provides a low-friction surface so the drawer slides smoothly and evenly.
• Protects the drawer edge and track from wear, cracking, or catching.
• Helps reduce sticking, grinding, or squeaking during drawer operation.
• Restores proper alignment when a liner is torn, warped, or missing.

• Remove drawer and contents before installing; handle glass or fragile parts carefully.
• Clean the track and mating surfaces before fitting the new liner.
• Press or slide the liner into place until it seats fully; no special tools are typically required.
• If mounting clips or tracks are damaged, replace those parts to ensure a secure fit.

This mounting cup installs in the freezer liner to create a secure attachment point for the ice maker or its bracket. It helps keep the assembly stable and properly aligned so the ice maker mounts firmly and operates reliably. What it does:

• Provides the receiving anchor for the ice maker/bracket mounting screw
• Helps hold the ice maker level and reduces movement or vibration
• A worn, stripped, or missing cup can prevent the screw from tightening
• Common signs include a loose or sagging ice maker, rattling, or difficulty keeping the ice maker aligned

• 1 mounting cup

• Disconnect power and shut off the water supply before servicing
• Remove the ice maker to access the cup location
• Seat the cup fully into the liner opening, then reinstall the bracket/ice maker and mounting screw
• Do not overtighten; verify the ice maker sits level and clears the fill tube

This rail guide assembly supports and guides a refrigerator or freezer drawer for smooth, stable opening and closing. It restores proper drawer alignment and helps prevent binding or accidental removal. What it does:

• Provides a track and guide for the drawer to slide in and out smoothly
• Keeps the drawer aligned to prevent sticking, jamming, or uneven movement
• Helps prevent the drawer from falling out when fully extended
• Restores normal drawer operation when original guide is cracked, worn, or broken

• One rail guide assembly

• Basic hand tools required; remove drawer to access mounting points before replacing guide
• Compare new part to the old part for orientation and matching mounting locations
• Do not force parts; ensure clips or screws are fully engaged to secure the guide
• Disconnect power only if required to remove interior components; follow appliance-specific safety instructions

Color: white. Measures about 2/3 of an inch wide by 1/2 an inch deep.

This right-hand side adapter bracket secures the appliance cabinet or panel, restoring proper fit and stability. Replacing a damaged or missing bracket helps stop loose or misaligned panels and reduces rattling. What it does:

• Secures the right-side cabinet or panel to the chassis to maintain alignment and support.
• Helps eliminate panel movement, vibration and rattling that result from a cracked or missing bracket.
• Restores correct panel gaps so doors or drawers operate and close properly.

• Disconnect power (unplug or shut off breaker) before accessing the appliance.
• Remove the required access panels to reach the bracket; keep and reuse existing fasteners unless new hardware is specified by the model diagram.
• Transfer the bracket into position and fasten securely; check for proper panel alignment after installation.

Right hand side

This is a genuine replacement shelf support that is designed for use in select freezers and refrigerators. The metal shelf support is installed on the side or back wall of the fridge or freezer unit and holds the shelf in place. It is made of durable metal, but it can become bent or otherwise damaged. In some cases, it may become detached and lost, which would also require a replacement. It's important to get an OEM part like this to ensure an identical fit. This OEM shelf support is manufactured to exact specifications by Frigidaire and can be used in select models from the brand, as well as those from Kelvinator and Gibson. This shelf support can have several applications on various models so it will be important to check the owner's manual parts diagram before installing this part. This genuine support is sold individually. Additional parts and hardware will require an additional purchase. Always wear gloves when performing appliance repairs, even when replacing accessories like this, to protect the hands.

This left-side adapter secures the appliance's panel components and helps maintain proper alignment for reliable operation. It's a direct replacement that restores fit and support where the original left-side adapter is damaged or missing. What it does:

• Replaces a worn or broken left-side adapter/bracket to restore panel alignment and support
• Helps prevent rattling, misalignment, or loose panels that can occur with a damaged adapter
• Fits the left side mounting points to secure adjacent panels and components
• Works as a structural support piece in the appliance's chassis assembly

• 1 left-side adapter

• Disconnect power and water before starting any repair
• Handle panels carefully to avoid bending; support panels while removing fasteners
• Use the original fasteners unless replacements are specified by the manufacturer

This freezer slide support assembly stabilizes and guides a freezer drawer so it opens and closes smoothly and stays level. Replacing a worn or broken support restores proper drawer alignment and prevents sagging or catching. What it does:

• Supports the freezer drawer or slide to maintain proper alignment and smooth movement
• Keeps the drawer level to prevent binding, sagging, or accidental dropping
• Replaces cracked, worn, or missing support pieces that cause uneven operation
• Works as a direct-fit mounting/guide for the drawer slide mechanism

• One freezer slide support assembly

• Disconnect power before starting and remove the freezer drawer to access the support
• Inspect mating slide and mounting tabs; replace any damaged clips or hardware
• Typically installs by snapping or securing into the existing slide track—retain fasteners if present

This right-side glide bucket replaces the refrigerator door/bin glide that holds and organizes items while sliding smoothly. Restores proper storage and secure positioning on the door rail for everyday use. What it does:

• Replaces a cracked, broken or worn right-side glide bucket so items stay contained on the door
• Restores smooth sliding action on the door rail for easy access to stored items
• Prevents items from tipping or falling when opening or closing the door
• Matches the OEM shape for proper fit and alignment with the existing rail

• One right-side glide bucket

• Disconnect power to the appliance before performing service as a safety precaution
• Remove items from the door and gently lift/slide out the old bucket per manufacturer guidance
• Inspect door rail and attachment points for damage; replace damaged clips or rails as needed
• Handle carefully to avoid snapping mounting tabs during installation

This Slide Outer is the outer rail that supports and guides a refrigerator shelf/drawer, restoring smooth movement and proper alignment. It replaces a worn or broken outer slide to help shelves glide and stay level. What it does:

• Guides the shelf or drawer on one side and provides structural support during use
• Replaces a cracked, bent, or worn outer rail that causes sticking or uneven movement
• Helps restore proper alignment when a shelf tilts or binds while sliding
• Works with the matching inner slide and mounting hardware to enable smooth operation

• Disconnect power and empty the shelf/drawer before starting work
• Remove the shelf/drawer and any clips or screws holding the old slide; install in reverse order
• Use only the matching inner slide and hardware; fit before final assembly
• If mounting points are damaged, inspect cabinet/frame and replace as needed for secure installation

This left-side meat pan rail block secures the meat pan/drawer slide in place so the drawer opens and closes smoothly. It replaces a worn or broken support to restore proper alignment and prevent the drawer from sagging or catching. What it does:

• Supports the left end of the meat pan/crisper drawer rail for stable sliding action
• Prevents the drawer from tilting, binding, or falling out when loading
• Replaces cracked, worn, or missing blocks that cause noisy or uneven drawer movement
• Keeps the drawer aligned for proper sealing and reliable operation

• Disconnect power to the appliance before servicing to avoid injury.
• Remove the meat pan/drawer per the appliance guide to access the rail block.
• Snap or screw the block into the rail per OEM alignment; do not force parts.
• If hardware is damaged or additional guides are worn, inspect adjacent components and replace as needed.

Left side.

A replacement hanger basket that supports items inside the appliance so clothes or components stay organized and secure. Restores proper basket support and helps prevent sagging or shifting during operation. What it does:

• Holds and supports garments or items in the appliance basket area
• Helps maintain even load distribution to reduce rubbing or snagging
• Can resolve symptoms like a loose, tilted, or missing basket support
• Replaces worn or damaged hanger/basket hardware

• One hanger basket

• Disconnect power before inspecting or replacing parts
• Remove surrounding panels or components as needed for access
• Use basic hand tools; handle sharp edges carefully