Refrigerator Touch Pad

This HMI assembly is the user-interface control panel that lets you operate the appliance's front controls and display. Replaces a damaged or unresponsive control surface to restore button and display functionality. What it does:

• Provides the push-button controls and display interface for operating the appliance.
• Sends user commands to the main control board for functions like cycle selection, options, and start/stop.
• Commonly replaces units that are cracked, have unresponsive buttons, or show display errors.
• Helps resolve intermittent or failed front-panel communication when the HMI is the diagnosed fault.

• High-level replacement only; refer to factory service literature for step-by-step procedures.
• Disconnect power to the appliance before servicing to avoid shock or damage.
• Handle the assembly carefully to avoid damaging connectors, ribbon cables, or the display lens.

This separator is a molded plastic divider that helps keep ice organized inside the ice bin for smoother dispensing and less clumping. It restores proper spacing so ice moves freely during dispense cycles. What it does:

• Divides and guides ice inside the ice bin to reduce jamming and clumping
• Helps improve ice feed into the auger or dispenser chute
• Reduces shifting and rattling of ice during door movement
• Restores intended bin geometry after a cracked or missing divider

• One separator

• Unplug the refrigerator or shut off power before working on the ice bin or dispenser
• Empty the ice bin and remove any loose ice to avoid spills during replacement
• Snap the separator into the molded slots in the ice bin; no tools typically required

Replacement dispenser housing shield that protects internal dispenser components and restores a clean, finished appearance. Fits the dispenser area and helps prevent damage from spills or impacts while improving dispenser alignment and usability. What it does:

• Shields internal dispenser parts from spills, debris and everyday wear.
• Restores proper fit and finish to the dispenser opening for consistent cup placement.
• Common replacement when the dispenser guard is cracked, broken, warped or missing.
• Helps reduce risk of leaks and keeps controls and mechanisms covered.

• Disconnect power to the appliance before starting any repair.
• Typically requires removal of the dispenser front or trim; basic hand tools recommended.
• Retain or transfer any clips, screws or brackets during replacement.

This membrane switch is the flexible button panel that sits under the appliance control bezel, restoring responsive push-button input and clear button labels for the control console. It's a direct-fit replacement for a worn or damaged keypad surface. What it does

• Registers user button presses and sends input to the appliance control board.
• Replaces cracked, faded, or unresponsive keypad areas that no longer activate functions.
• Helps resolve intermittent or failed button responses when the keypad is the root cause.
• Restores correct tactile feel and button alignment under the front bezel.

• Disconnect power or unplug the appliance before beginning any service.
• Remove the control bezel or console to access the membrane; handle the thin membrane carefully to avoid creases or damage.
• Align the membrane over the control board and seating posts, then reassemble the bezel; ensure any adhesive or locating tabs are correctly positioned.

This control box is the electronic control assembly that manages appliance functions and user inputs, restoring normal control response and cycle operation. It replaces a failed or unresponsive control module to help the appliance run correctly. What it does:

• Houses the main control circuitry that sends and receives signals for cycles, timers, and user commands
• Replaces a control box that causes unresponsive buttons, error codes, or intermittent operation
• Restores proper communication between the user interface and internal components
• Helps stop erratic cycles, failure-to-start issues, or unexpected shutdowns when the control is defective

• One control box (electronic control assembly), as shown

• Disconnect power before servicing to avoid electric shock; verify power is off at the breaker
• Handle the board and connectors carefully to avoid static or physical damage
• Confirm connector locations and reinstall any mounting hardware in original positions

This control case assembly is the outer housing that holds and protects the refrigerator's control board and user interface, restoring a secure mounting and clean appearance. It replaces cracked, broken, or missing control housings on compatible units. What it does:

• Secures the control board and interface components to prevent movement and electrical contact
• Protects electronics from moisture, dust, and accidental impact
• Restores proper alignment for buttons, knobs, or display panels for reliable user operation
• Helps resolve symptoms such as loose or wobbly controls, exposed circuitry, or a damaged control bezel

• Always unplug the appliance before starting work to reduce risk of shock
• Handle the control board and connectors carefully; avoid touching circuit contacts
• Remove any trim or access panels as needed; keep and reuse original screws and fasteners

This dispenser trim is the exterior bezel that surrounds a refrigerator's ice/water dispenser, restoring a finished appearance and protecting internal dispenser components from daily wear. It replaces cracked, chipped, or faded trim pieces. What it does:

• Provides a finished, protective bezel around the dispenser opening
• Helps keep the dispenser area aligned and prevents gaps that trap dirt or moisture
• Commonly replaced when trim is cracked, broken, loose, or cosmetically damaged
• Restores proper fit and appearance after impact or wear

• Disconnect power to the appliance before starting work; shut off the water supply if the dispenser is connected to plumbing
• Installation typically requires removing the inner dispenser panel or door trim; keep track of all fasteners
• Handle edges carefully — trim pieces or adjacent metal can be sharp