Kgrs 206Xs Parts

I have a Jennair jjw9630cas double wall oven, and after a few years I noticed that the light would not go out, first in the bottom oven, and then in the top oven. After doing some research I discovered this was not uncommon, and the fix usually involved replacing the hinges and/or the hinge receptacles. It didn't look like a difficult fix so I ordered four new hinges and four new receptacles, which arrived quickly. I found a video on YouTube that showed how to replace the hinges and it... Read more

• Oven is too hot
• Little to no heat when baking
• Won't start
• Oven not heating evenly

When bake was set, the stove would function normally, it would show pre-heating then get up to temperature and beep twice like normal when it reached the set temperature. Shortly after it would start beeping and scroll “ fault detected, press start to try again” across the display. Pressing start did not resolve, the message would continue to post and the pizza inside was burnt. We noticed the broil element was glowing. This model stove does use the broil element for backing but it... Read more

• Little to no heat when broiling
• Gas igniter glows, but will not light
• Gas smell
• Little to no heat when baking

I used the little video clip shown under the part and replaced it myself. Read more

Took the stove apart*, saw where the mouse had made a nest. It was kind of like a hotel room after a rock star had used it. It was nasty, is what I'm saying. I removed the insulation, which immediately went into a garbage bag and was placed outside, whereupon I took off and nuked the site from orbit. It was the only way to be sure (actually it was disposed of in the proper manner, no nukes were detonated in the course of this repair). Anyway, I ordered the insulation from this site, which was... Read more

• Oven is too hot
• Little to no heat when baking
• Won't start
• Oven not heating evenly

Online videos made this seem an easy fix. I unplugged the oven and removed the rear panel, then found where the temp sensor entered the oven. I unplugged the sensor's electric connector. Unlike the videos, this sensor screwed in from the inside of the oven, so I had to remove the 2 screws inside the oven which hold the sensor in place. Then I pulled the sensor out, careful not to tear the insulation with the wires and connector. Then I just pushed the new connector through the same hole and... Read more

I bought an( as is) range (Maytag) form a dealer. I assumed that it would have racks, however, it came without. I tried to find some racks that would fit but none available. So I decided to order from Appliance Pros and received the right racks two days after I ordered. Very Happy Camper, Read more

I have tried to remove the burner assemblies by removing the torx screws but they were badly rusted, and unfortunately they all were broken during removal. I just discarded the ruined orifices and assembled the new orifices and burner assembly. Read more

• Little to no heat when baking

The bake (bottom burner) worked after replacing the ignitor. Becareful and do not drop the ignitor or the element will break. I found out the hard way. I bought the first ignitor at a local appliance store. After breaking that one, I found another at appliancepartspros.com for $20 cheaper. Thanks appliancepartspros!!! Read more

Replaced the gas regulator and the oven igniter. It was not a very difficult repair.. most of the parts were easy to get to. The biggest challenge was disconnecting the gas hose from the regulator. It had "pipe dope" (sealant) on the threads. I reconnected with yellow gas pipe tape. Read more

Touch up paint Read more

Replaced It With New One Read more

DIY. The delivery to Milwaukee took two days. The project was very easy and took about 1hr. The only tools required were a screw driver (electric) and a pliers. Just make sure your irganized with the screws so you don't lose any or mix up which ones go back in which holes. There's about 20 total screws. This $50 part saved me from having to buy my wife a $1000+ oven. Read more

I ordered a new socket and replaced the socket and now we have a light in the oven. The project took about 10 minutes and was easy done. Read more

Removed existing gasket and replaced with new gasket in less than 5 minutes. Very Easy. Make sure to remove the lower burner cover (inside the oven) which allows you to pull the end gasket material through the two circular openings in the frame. Read more

Replaced old igniter. also purchased new screws for burner and igniter assembly since old screws were corroded from spilled food/fluids etc over the years. made the installation much easier. If you need to replace a worn igniter, do yourself a favor and go to hardware store and get matching replacement screws or buy new with igniter. Now my front right burner lights every time with just a click or two. Very pleased. Read more

• Won't start

I purchased a new igniter for the bake assembly and found that it, unfortunately, did not resolve my problem. I measured the resistance of the different points on the gas valve and it was reading within spec so I then purchased this spark module and it did the trick. My gas range is a Kitchenaid kgsk901sss02. I had a LOT of trouble finding where the spark module is located, and eventually found a schematic that shows it's location behind the front control panel of the oven. Upon taking the... Read more