Pdw 8680J00ss Parts

• Fridge too cold
• Too warm
• Fridge runs too long
• Freezer too cold

I unplugged the fridge and took all the food and shelving out of the freezer and then proceeded to take off the bottom sliding drawer rack on both sides off (4 Phillips head screws). Then took off the light bulb cover and then the light bulb. Then the back wall that covers the coils and tubes that the refrigerant runs through ( 2 screws with hex head). After sliding out the back wall I could see that the entire coil area was frosted and iced up. I took a blow dryer and melted all of it over... Read more

• Ice maker not making ice
• Ice maker won't dispense ice
• Leaking

Much easier than expected, I was certain it had to be a water line but the solved everything Read more

• Will not fill with water

Pulled out the unit, found the inlet valve was leaking. Went on AppliancePartsPros.com and ordered a new valve. That was Saturday evening. Tuesday I got my part and installed it. Thanks for the fast delivery. Read more

• Door won't close

I never respond to these kinds of requests but I must respond to this one because of your superior service! The best story here was that I ordered the parts from AppliancePartsPros at 4:15 p.m. one day, and they were on my porch by 2:00 p.m. the next day!! I am very impressed, so please keep up the great work. I'll add that the prices were the best I found too. The dishwasher wheels replacement didn't require tools & took less than 15 minutes. The original design/materials are not very... Read more

Our GE was installed about 8 years ago and was AWESOME for much of its early life. However, progressively its cleaning ability diminished. By replacing all the spray arms (clogged with debris), filters, drain hose, and sump...this dishwasher cleans like it did when it was new! Cost was around $100 (also replaced a wheel and the silverware basket) and labor was relatively simple. And to think...my mother-in-law said, "Wouldn't it just be easier to buy a new one?!?". Read more

• Door latch failure

Replaced the pump drain assembly Read more

• Door latch failure
• Ice maker not making ice
• Not dispensing water
• Ice maker won't dispense ice

My refrigerator is 13 yrs old and began to build up frost in the ice cube shoot and the water tube began to freeze up over night. The flapper door was not closing completely. I simply removed the control panel by pulling up and out on the bottom edge, the edge is only about 1/8 inch thick, so don't reach in to far. You should be able to feel a small division line between the control panel and the refrigerator. No screw driver was needed to expose the 4 mounting screws of the inner dispenser... Read more

The indication was that when I tried to use the icemaker or water dispenser, the green LED on the front would dim and the ice maker dispenser wouldn't work. It was intermittent at first, but this indicated it may be a power management issue, in that insufficient voltage was getting to the ice dispenser motor. I unplugged the unit to reset the electronics for about a minute, and when I plugged it back it the compressor would try to turn on (solenoid or relay would click about every two... Read more

We replaced the main circuit board and the LED started to work and the condenser fan worked, but all we had were relay clicking sounds, but no cooling. The compressor had become so hot trying to work when the main circuit board was amiss, that it had popped the over temperature sensor on its side. As some one point out, if you remove the PTC+OLP assembly with the capacitor on it, and shake it, you will hear a rattle inside---and that is bad. We ordered a second round of parts from... Read more

Purchased replacement rack with wheels that were better equipped. This rack is way better than the original that was falling apart. The wheels came off and the prongs broke. This replacement part seems to be constructed well. Read more

• Leaking
• Not dispensing water

We noticed a puddle of water in front of the fridge a couple of months ago-dried the floor up both times and thought someone had dropped ice-or spilled water. A couple of weeks ago there was water dripping through the dropped tile ceiling in the basement. I shut off the water for the water supply to the fridge at the copper pipe in the basement and removed some of the tiles which felt a little damp. It still dripped all day. When my spouse came home he pulled down more of the tiles. It was as... Read more

All parts arrived in one box - I purchased the tub gasket, lower door gasket and lower door seal. My existing parts were visibly pretty worn out, dishwasher is 12 years old (maybe should have just bought anew one?). Tub gasket was pretty easy, it took me a while to make sure it was even all the way around, after attest run and the subsequent drying heat it fits nicely. Lower door seal went as video, all good, my other one was destroyed from the heat cycles. Could not get the lower door seal... Read more

I watched the repair video and ordered the part ( I luckily ordered two links). The video was not exactly for my model dishwasher but I did follow the instruction for removal from the cabinet. Since my model was not shown, I was looking to see how the door spring and the Hinge Arm Link was supposed to be set up. I had the impression that the door spring and link was only on the right side of the dishwasher. I finally figured it out and took pictures of the set-up for the next time the link... Read more

• Will not dispense detergent

Bought the replacement dispenser from APPros.com (of course). The video shows a front control panel, and our dishwasher has the 'hidden' control panel on the top of the door. So here's the difference: 1) You need to take out all the screws, except the two near the latch at the top. The other video shows only taking out the bottom six screws because the remainder of the screws hold the front control panel. I used a couple paint cans with rags on top to hold the corners of the door when... Read more

My daughter replaced the wheels. I showed her how to remove the old wheel and snap on the new ones. Easy fix that empowers her to try repairs on her own. Read more

This was actually one of the easiest fixes I’ve done. All that was required was to remove 3 screws to remove the broken part. I used a pair of pliers to remove the moisture sensors from the broken part to the new one. Read more