Kitchenaid Kuds30ixss0 Parts

• Door won't close

I found the door switch was not making contact when the door closed. I adjusted it, but then it would not open so the dishwasher would run when the door wasn't closed. The contacts were too long in the switch so they would bend and stay together when the door opened. The original switch was very poorly made for a very expensive Maytag dishwasher. The new switch you supplied was much better quality and easily replaced the one that was installed at the factory. I was a little baffled at the... Read more

• Door won't close

Ordered new brackets from parts pro.com Got in 3 days And installed , dishwasher doesn't fall out of counter anymore when you pull out the shelves. Read more

The lower basket L& R track bearing brackets on my KitchenAid dishwasher (KDTE704DSSO) finally gave out (ball bearings everywhere) after (6) years of daily, family use. The service techs provided me with all the information I needed to successfully and quickly complete my project. My parts were mailed to me very quickly and my dishwasher was up and running in short order. The parts were clean and in perfect working condition. (After pulling your dishwasher out, there are two sets of screws on... Read more

My wife said we have a problem with our dishwasher (Whirlpool WDT920SADE2). The dishes were not getting clean, and the soap dispenser opened, but soap was still dribbled down the inside of the door and on the silverware caddy. I'm not the handiest guy; it took me several days to go through the trouble-shooting process, watching multiple videos and trying different things. My initial guess was that the soap dispenser was opening too late. (This turned out to be wrong.) I started off by... Read more

• Will not drain

I've opened sump housing to check for clogging but it was clean. When I removed check valve to inspect it I've found out that the round part of the valve was missing so I figured it might've blocked the water exit at drain hose or something like that. So I pulled the dishwasher out to get a full access to drain hose connector and the pump. Upon disconnecting the drain and checking its connector I indeed found the round piece totally blocking the hose and acting as a seal. I removed the piece... Read more

Just replaced the things. Had to reuse old tine rows, rollers, the spray arm, etc., i.e. I removed 'em from the old racks and put on the new ones, but that was piece of cake. Also, I cleaned the food grinder and the discharge valve compartment (thank you very ???? ???? much, Internet), so spray arms around the top rack get enough water pressure now. I didn't have to buy any parts for the latter part of this little repair project, though. Read more

Ordered 6 parts from you thanks to your fantastic web schematic parts diagram received parts very fast changed parts easily and that leak stopped. Your company is a 5* operation hands down. Read more

While this is a Whirlpool dishwasher, I have the Kenmore Elite version of it. I believe them to be identical for parts. A little background: The first symptom I had of problems was plastic bits from the ball bearing retainer strips in the slides falling out. Then ball bearings falling out. A common problem with this dishwasher. When disassembling the upper basket, some of the gray plastic pieces were very brittle and easily snapped off. So I ended up replacing all of the plastic pieces related... Read more

My discharge would not empty after a wash cycle and I always had gross gray water left in the bottom approx 3" deep? After doing the obvious things of checking the simp for garbage, and checking that the discharge hose wasn't blocked, I removed my discharge pump ( not too hard to do) and tested. My pump which did run and turn the impeller. However, the pump evidently had weakened with time and weakened and could no longer pump the waste water up hill to the "T" connection under the sink. A... Read more

• Not cleaning dishes properly

I called to ask about the correct gasket for the door. As VERY helpful lady suggested that it was probably a split arm spray. She was absolutely correct. I have used you web site for parts in the past and will always make it my first stop when ordering appliance parts. Read more

My dishwasher was running super loud for several loads but appeared to be cleaning just fine. One day it went from super loud to hardly a sound at all, not even the sound of water. After finding this site I found others with similar issues and it pointed to the Circulation Motor. Normally I wouldn't feel comfortable with pulling the dishwasher out of it's slot and performing this type repair but after watching the video posted along side the pictures of the part it looked pretty easy so I took... Read more

We looked for a supplier of the part and came across AppliancePartsPros. They had the parts in stock and the prices were reasonable. We ordered the parts sometime on Thursday afternoon. The needed parts arrived on Friday around 11:00A. Wow, what fast service! Read more

Replaced the upper spray arm seal Read more

While this is a Whirlpool dishwasher, I have the Kenmore Elite version of it. I believe them to be identical for parts. A little background: The first symptom I had of problems was plastic bits from the ball bearing retainer strips in the slides falling out. Then ball bearings falling out. A common problem with this dishwasher. When disassembling the upper basket, some of the gray plastic pieces were very brittle and easily snapped off. So I ended up replacing all of the plastic pieces related... Read more

Ordered 6 parts from you thanks to your fantastic web schematic parts diagram received parts very fast changed parts easily and that leak stopped. Your company is a 5* operation hands down. Read more

I bumped into my KitchenAid dishwasher and the upper rack adjuster cracked. There was already a crack on the notch of the housing where the handle (lever) sits. In addition, the positioner popped out and I couldn't find it. So, I bought the three parts from AppliancePartsPros online. It arrived in about a week. The repair was fairly simple, but it still took about 45 minutes because I didn't want to crack the assemblies. For the housing, use a small slotted screwdriver to carefully... Read more