Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Creates an airtight seal to maintain temperature and prevent cold air leaks. Replace if worn, cracked, or failing to seal properly. Verify fit with your model.
Ordered the correct gasket, watched video and completed the repair myself. Wasn’t hard at all. Read more
Fix ice not dispensing or motor running but no ice with this refrigerator ice dispenser spring. Essential part for cubed and crushed ice. DIY repair.
The problem was that the motor coupler & shaft had a tiny bit of rust at their union. With the weight of the ice bin it rusted in the lowest position. This didn't allow the motor coupler to float on the shaft. There is a spring inside the shaft that pushes up on the motor coupler keeping it engaged in the ice bin coupler above. This coupler in turn rotates the auger in the bin to dispense the ice. I removed the motor coupler & shaft, tapped the coupler loose and filed off the rust. This allowed... Read more
Refrigerator not cooling but freezer works fine? The air damper controls cold air flow between compartments. DIY-friendly repair with video guide.
The site came up on a Google search suggesting a new air diffuser which was indeed the problem. I got a thermistor too just in case but probably want needed. Saved a fortune compared to a repair man and was able to cancel an order I had for a new unit saving over $1200+! Very happy with the whole process and videos on you tube etc. Great site! Thanks! Read more
Water leaking from bottom of fridge? Cracked evaporator drip tray lets defrost water escape. Moderate DIY repair, about 45-60 minutes with our guide.
The drain pan (Tray-Evaporator Pan) was cracked in 2 places. We had to remove the front panel. Loosen the bracket that holds the water filter. Take off the back panel and disconnect the bracket that holds the selenoid. It was not necessary to unhook the water lines, just the bracket. It was not easy to remove the old pan and get the new one in, but holding the water filter, with the bracket intact, as far to the left side of the refrigerator as possible gave us the room to get the pan in. ... Read more
Water tube assembly supplies water from inlet valve to ice maker and dispenser in your refrigerator door. Replace if cracked, leaking, or broken.
After watching installation videos on each felt I could pull it off and ordered and received replacement water reservoir and water dispenser tube assembly. Reservoir installation went off without a hitch outside of the added step of the need to remove the entire main in waterline assy in order to access the connectors which also were not as represented in video, in that they were not the press-to-release type but standard threaded compression types. Water Dispenser tube/spout assembly was much... Read more
Fix an ice maker that stopped working or leaks water into the bin. This ice mold tray replacement takes about 10-20 minutes with our step-by-step video.
I have a Whirlpool Side-by-side Model ED22PWXBW01. A year ago, the ice cubes started freezing together in the rear of the ice bin for no apparent reason. Although the problem started off small, it gradually grew much worse, and finally I could see water dripping out of the ice mold and into the bin during the fill cycle. Re-levelling the refrig didn’t help, nor did adjusting the cube size / fill level. With guidance from the video, I removed the icemaker from the wall of the freezer. The... Read more
Secures the handle end cap to the center of your refrigerator door. Replace if missing, stripped, or lost during handle repairs. 8-18 x 1/2 inch size.
This was actually one of the easiest fixes I’ve done. All that was required was to remove 3 screws to remove the broken part. I used a pair of pliers to remove the moisture sensors from the broken part to the new one. Read more
Stores and chills water before dispensing. Replace if cracked, leaking, or causing slime/film buildup in dispensed water. Installs inside refrigerator.
Freezer icing up or refrigerator too warm? This defrost control board coordinates defrost cycles to prevent frost buildup. DIY-friendly 15-30 min repair.
Tried to put refrigerator in defrost mode and defrost would not initiate. Checked the bi-metal and heater, both tested good. Replaced the ADC board and refrigerator went in to defrost. problem solved. Read more
Fix a loose or wobbly dispenser paddle with this strain relief. Cushions the dispenser arm connection to prevent wear. Easy 5-minute repair with video guide.
With the help of the fantastic videos provided on the web site for each replacement part, it was extremely easy to complete the repair Read more
Fix leaking water or ice maker not filling? Water inlet valve controls flow to ice maker and dispenser. DIY repair takes 10-20 minutes with basic tools.
Replaced inlet valve. Read more
Refrigerator warm but freezer cold? Noisy evaporator fan? This mounting grommet reduces vibration and noise. Takes about 1 hour to replace with video guide.
I noticed Ice maker Quit for the third time in 15 years so I decided to buy another Ice maker, I installed it and NO ice still?? Well I went after the other problem thinking if it does not get cold enough maybe ice maker won’t work. I ordered Defrost Switch, Heater and Evaporator Fan just to be safe. I replaced all three, the fan was noisy, the heater OHM’d ok but I replaced it as did the defrost switch, I put it back together, the Freezer got to 0 degrees and the frig got to 38 degrees so I... Read more
Replacement shelf stud kit for refrigerator compartments. Secures adjustable shelves to interior liner. Needed when original studs crack or break off.
My Whirlpool fridge is 12 yrs old. The crisper drawer supports finally gave up. I googled the make and model number for repair parts and AppliancePartsPros.com came up. I was actually surprised that I found the support peg and stud. I watched the video on their site on how to replace them, saw that it was easy and ordered the parts that afternoon. To my utter amazement the parts came via FedEx the following afternoon! I have to admit if I didn't watch the video I wouldn't have known how... Read more
Ice dispenser not working or skipping? This coupling washer connects the auger motor to the ice bin. DIY-friendly repair with video guide included.
Bottom mounting screw for refrigerator ice maker auger assembly. Secures auger blade components together. Replace if stripped, damaged, or missing.
The Whirlpool refrigerator ice maker is a good design. The 8 32 screw was a problem I could not remove it with the thread lock it prevented me from unscrewing it. Therefore I replaced the shaft the splined hub and spacer washers. It seems to work fine now. Read more
Horizontal metal rod that secures glass shelf panels inside your refrigerator door. Replace if broken, bent, or missing to prevent shelf slippage.
Cut piece to fit Read more