Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
This is a small fiber washer that fits on the drum support roller shaft inside the dryer. It acts as a spacer and bearing surface to reduce friction and keep the drum roller properly positioned. Replace this washer if the dryer makes squealing, thumping, or scraping noises during operation, or if the drum rollers appear to wobble or wear unevenly.
In the past, I replaced some electronic components on our gas dryer, the solenoid and the electronic ignitor, but the rest of the dryer looked more difficult to repair if needed in the future. I was wrong. I went unto AppliancePartsPros.com and watched some repair videos on dryers like mine that make big thumping sounds while drying. This happened when I googled my dryer model number in an attempt to find out is capacity, because I wanted our new dryer to have the same capacity. I found out... Read more
The Clamp is an OEM part for Whirlpool dryers. This clamp ensures tight and secure connections within the dryer, particularly in securing ducts and vents that are essential for proper airflow and operation.
Clamps may need replacement due to loss of tension, corrosion, or damage from regular use. A compromised clamp can lead to operational issues such as prolonged drying times or excessive noise, resulting from loose parts or improper ventilation.
Symptoms of a bad Clamp include:
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.
Our Maytag gas clothes dryer was not drying like it should/used to and was making a lot of noise. After researching online I figured the vent was partially blocked and/or the blower wheel was bad. When I took it apart, the vent had very little lint in the lower elbow exiting the back of the dryer but the blower wheel was loose on the shaft and was missing the clamp. I cleaned out the vent and put a hose clamp on the blower wheel to tighten it to the shaft and tried it again. The noise was... Read more
The Idler Shaft Retaining Ring is an OEM replacement part for Whirlpool dryers. Also called an "E" ring, it is a sealing gasket positioned between the front and rear housing omponents. Maintaining an airtight seal prevents gas leakage and promotes efficient drying performance.
Causes of a bad retaining ring commonly involve compression loss of the rubber gasket material over many years of heating cycles. Exposure to petroleum-based cleaners may prematurely deteriorate the seal as well.
Symptoms of a failed 'E' ring include:
This OEM Whirlpool replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore gas dryer models.
First replaced the drum rollers...that wasn't it..took dryer back apart and spun the belt tension wheel by hand (should have done this the first time I took the dryer apart) and it squeaked. so I ordered the full parts: wheel, idler arm, idler spring, arm sleeve, E ring..Put it back together and whoa..no more squealing!! Read more
Pivoting metal arm that maintains belt tension in your dryer's drive system. Replace if bent, cracked, or wobbling excessively when drum is removed.
I removed the front panel of the dryer by removing 2 screws and lifting it up and out. Then I removed 4 screws from the bracket holding the tub in place. I had previously removed the 4 screws from the rear inspection cover so I reached in and released the spring loaded belt that turns the tub and then removed the idler pulley wheel. The tub just lifts out at that point, exposing the 2 Drum support rollers in the rear. I removed the 2 rear drum support rollers and decided to order 2 of... Read more
The Heater Assembly Complete is an OEM part for Whirlpool dryers, engineered to generate and maintain the heat necessary for drying clothes efficiently and uniformly. This assembly ensures that your dryer can reach and regulate the desired temperatures without overheating.
Causes of a bad Heater Assembly can stem from normal wear and tear, overloading of the dryer, insufficient maintenance leading to buildup and blockages, or electrical surges that damage the heating components.
Symptoms of a bad Heater Assembly Complete include:
I ordered all the parts necessary to replace the heating element and thermostat on a Sunday night. Appliance Parts Pros shipped on Monday AM and I received them on Wednesday. It took me 45 minutes to disassemble the dryer, replace the parts and have the dryer working again. It should be good for another 35 years which should cover me for my needs. Thanks again to Appliance Parts Pros for having the best service and always the correct parts. I am a huge fan of your company as you never... Read more
The Time Delay Fuse is an OEM part for LG microwaves. This fuse provides a safety mechanism by delaying the flow of electricity, protecting the microwave's electrical components from power surges and ensuring the appliance operates safely. It helps to prevent immediate damage in the event of a power surge or electrical fault, thus prolonging the lifespan of the microwave.
Over time, the time delay fuse can become damaged due to electrical surges, wear and tear, or faulty connections. If the fuse blows, it can disrupt the microwave’s ability to function correctly.
Symptoms of a bad time delay fuse include:
This OEM LG part is also compatible with Sears/Kenmore models.
Called AppliancePartsPros because of good experiencing diagnosing problem with a dishwasher repair. We definitely are modest income amateurs! Same excellent response to our questions. Three possible causes. Used easy search menu to fine replacement parts. Bought all three, knowing that if all not needed, the others could be returned (within 365 days) for refund. Replaced the capacitor successfully after calling to get more help with a couple of places where we got stuck. Oven now works... Read more
Dryer won't heat? A broken heating element is the most common cause. This coil provides heat for drying cycles. DIY repair typically takes 1-2 hours.
I took off the front cover and checked the sensors which were all good. Then I removed the cover for the heating coil after finding that it appeared open. Found that the coil had in fact broken but the break was not visible just by looking in. Located the break in the coil within an insulator near the back. I checked appliance stores locally and found the coil for far more than Appliance Parts Pros wanted for it. I placed an order after chatting with a tech, I placed and order and had it in... Read more
Dryer won't heat or start? This thermal fuse cuts power when temperatures get too high. Test with a multimeter for continuity. Easy DIY repair.
Did some dryer repair research (dryer not heating) on the internet. Bought an ohm meter, opened up the dryer and tested the cut-off-T, high limit thermostat, dryer igniter, flame sensor, cycling thermostat for continuity. The igniter was bad, the other parts tested ok. Went online to AppliancePartsPros.com searched for a new igniter for my specific dryer model, found the right replacement igniter and watched the video on how to replace the igniter. Because my dryer is old (15+ years) and I... Read more
The Whirlpool screw is an OEM replacement part responsible for securing various components or parts on different types of Whirlpool appliances. The screw is designed to provide a secure and reliable fastening connection, ensuring that different parts of the appliance stay in place. It is commonly used in different locations within the appliance, such as the cabinet, panels, or other structural elements. This part fixes the following symptoms:
The Whirlpool screw can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
One day my wife went to bake something and the bake/broil buttons as well as #3, #9, and oven light ceased to work. Local repair guy came by and wanted to charge $500 to fix it....YEAH RIGHT! Did a little homework and found this website, spoke with knowledgable staff who pointed me in the right direction. Took me all of about 20 minutes to install new control panel..everything works perfect...THANKS! p.s. In doing my research come to find Maytag did little to insulate control panel from oven... Read more
Factory fastener screw secures panels, brackets, and trim inside appliances. Replace missing, stripped, or damaged screws to restore tight fit.
Replace a burned-out smoothtop burner that won't heat. This radiant element restores consistent heating to glass cooktop zones. Simple DIY repair.
Removed old burner, replaced it with new burner. Pretty simple. Read more
This Hex Nut is a small but critical fastener used to secure brackets, panels, and internal assemblies in your appliance. Replacing a stripped, corroded, or missing nut restores a tight, rattle-free, and safe installation.
It took me about 2 hours to take everything apart and get it back together & running again with no problems. All the parts I ordered were exactly what I needed to fix everything. Thank you all !!! Read more
The Screw is an OEM replacement part for Whirlpool appliances. The precise threads allow screws to join or assemble other parts securely.
Causes of a bad screw can include stripping, cracking, or loss of threads due to repeated installation/removal over time. Corrosion is also possible depending on environmental conditions.
Symptoms of a bad screw include:
Found the parts in the diagram of my fridge and simply installed it very easy Read more
Seals the gap between drum and bulkhead to maintain airflow and drying performance. Replace when worn to reduce noise and prevent snagging. Verify fit.
I replaced the seals and tub bushings to bring back a quieter operation and keep from doing more damage.I have done so since it was new in 1990. It still has a lot of kife left in it. And it beats buying a new unit any day. Read more
Secures components with constant tension to prevent looseness and vibration. Replace if broken, fatigued, or missing. Verify fit with your model number.
Replaced them. Read more
This jumper wire links two terminals in the appliance's wiring harness to complete a required circuit. Replace a burnt, broken, or heat-damaged jumper to restore reliable power flow and prevent intermittent operation or arcing at the connection.
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.