Lde8000acw/A5122731 Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: WP6-3033630
Pivoting metal arm that maintains belt tension in your dryer's drive system. Replace if bent, cracked, or wobbling excessively when drum is removed.
Do-It-Yourself Stories from Customers like You
Clothes dryer had developed a loud squealing noise the problem turned out to be the idler pulley wheel Don F. • Bakersfield , CA • September 19, 2020
I removed the front panel of the dryer by removing 2 screws and lifting it up and out. Then I removed 4 screws from the bracket holding the tub in place. I had previously removed the 4 screws from the rear inspection cover so I reached in and released the spring loaded belt that turns the tub and then removed the idler pulley wheel. The tub just lifts out at that point, exposing the 2 Drum support rollers in the rear.
I removed the 2 rear drum support rollers and decided to order 2 of...
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WPY308612
Dryer not heating or overheating? This heating element assembly with enclosure and insulators is the likely fix. DIY install in 30 minutes.
Do-It-Yourself Stories from Customers like You
Overheating maytag dryer Mike H. • Sammamish , WA • December 31, 2015
Our dryer suddenly began overheating while drying. Outside of the dryer cabinet was uncomfortably warm to the touch, dryer drum was hot, charred smelling laundry. Based on what I read it was likely one of two things - a failed cycling thermostat or a shorted heating element. First I cleaned the vent hose and ducting to ensure good airflow, which I had.
I opened the circuit breaker first, then took off the door and front cover. I started with a thorough cleaning of the dryer with a vaccuum...
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP307473
Dryer won't start or heat? A blown thermal fuse cuts all power to protect against overheating. Easy 30-minute DIY fix with multimeter testing.
Do-It-Yourself Stories from Customers like You
Catastrophic failure of the dryer cycling thermostat in a maytag neptune super stack Richard M. • Cornish , NH • October 19, 2020
Through 15 years of vibration, the Cycling Thermostat evidently had degraded to the point where one electrical connection or more came loose and caused a short. There is also a possibility that the Bakelite section of the Dryer Cycling Thermostat body separated from the metal base, simultaneously exposing all four connections to a short. The thermostat literally exploded into chunks and dust. There was a heavy arcing and then, thankfully, the thermal fuse blew and shut down power to the short...
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP90767
The Whirlpool screw is an OEM replacement part responsible for securing various components or parts on different types of Whirlpool appliances. The screw is designed to provide a secure and reliable fastening connection, ensuring that different parts of the appliance stay in place. It is commonly used in different locations within the appliance, such as the cabinet, panels, or other structural elements.
This part fixes the following symptoms:
- Loose or wobbly components within the appliance
- Panels or parts that are not securely attached
- Rattling or unusual noises due to loose parts
- Damaged or missing screw
The Whirlpool screw can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
Do-It-Yourself Stories from Customers like You
Certain buttons were'not working Brent T. • Easton , MD • November 17, 2014
One day my wife went to bake something and the bake/broil buttons as well as #3, #9, and oven light ceased to work. Local repair guy came by and wanted to charge $500 to fix it....YEAH RIGHT! Did a little homework and found this website, spoke with knowledgable staff who pointed me in the right direction. Took me all of about 20 minutes to install new control panel..everything works perfect...THANKS!
p.s. In doing my research come to find Maytag did little to insulate control panel from oven...
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP306604
Dryer won't heat or start? This thermal fuse cuts power when temperatures get too high. Test with a multimeter for continuity. Easy DIY repair.
This part fixes the following symptoms
-
Won't start
-
No heat or not enough heat
See more...
Do-It-Yourself Stories from Customers like You
Maytag gas dryer was not heating Christopher P. • Los Angeles , CA • October 04, 2014
Did some dryer repair research (dryer not heating) on the internet. Bought an ohm meter, opened up the dryer and tested the cut-off-T, high limit thermostat, dryer igniter, flame sensor, cycling thermostat for continuity. The igniter was bad, the other parts tested ok. Went online to AppliancePartsPros.com searched for a new igniter for my specific dryer model, found the right replacement igniter and watched the video on how to replace the igniter. Because my dryer is old (15+ years) and I...
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WPY014874
Factory fastener screw secures panels, brackets, and trim inside appliances. Replace missing, stripped, or damaged screws to restore tight fit.
Do-It-Yourself Stories from Customers like You
Loud squealing noise William B. • Rocky Mount , NC • December 17, 2018
First replaced the drum rollers...that wasn't it..took dryer back apart and spun the belt tension wheel by hand (should have done this the first time I took the dryer apart) and it squeaked. so I ordered the full parts: wheel, idler arm, idler spring, arm sleeve, E ring..Put it back together and whoa..no more squealing!!
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WPY304475
The Cycling Thermostat is an OEM part for Whirlpool dryers. This thermostat regulates the temperature inside the dryer by cycling the heating element on and off to maintain a consistent temperature. .
Causes of a bad cycling thermostat can include wear and tear over time, electrical faults, or damage due to overheating.
Symptoms of a bad Cycling Thermostat include:
- Clothes taking too long to dry
- The dryer not heating at all
- The dryer overheating
- Erratic or inconsistent drying temperatures
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.
Do-It-Yourself Stories from Customers like You
It was taking unusually long to dry a typical load Robert L. • Williamsburg , VA • November 15, 2014
I removed the front panel and observed the heating element while running the dryer. It was cycling off every minute or so and staying off for several minutes. Even though it was likely the high temp cycling thermostat I replaced both the 14, and 15 cycling thermostats which I think are the original factory units. That makes them nearly 35 years old. Problem fixed.
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP33001443
This Hex Nut is a small but critical fastener used to secure brackets, panels, and internal assemblies in your appliance. Replacing a stripped, corroded, or missing nut restores a tight, rattle-free, and safe installation.
- Threads onto a matching bolt or stud to clamp parts together
- Helps maintain alignment and reduce vibration-related loosening
- Commonly used on panels, brackets, supports, and internal assemblies
- Replace when threads are damaged, hex flats are rounded, or hardware is missing
- Symptoms can include loose or rattling components or hardware that won't stay tight
What's included: One hex nut. Install notes:
- Disconnect power and, if applicable, shut off gas or water before servicing
- Use the correct-size nut driver or wrench to avoid rounding the hex
- Start the nut by hand to prevent cross-threading; tighten snugly without over-torquing
- Inspect and replace any damaged mating bolt/stud or washer for a secure repair
Do-It-Yourself Stories from Customers like You
The rollers needed to be replaced, the axles for the rollers needed to be replaced, the tension pulley roller needed to be replaced, the belt needed to be replaced Richard G. • El Paso , TX • December 18, 2018
It took me about 2 hours to take everything apart and get it back together & running again with no problems. All the parts I ordered were exactly what I needed to fix everything. Thank you all !!!
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP307178
Dryer not heating or producing warm air? This heating element assembly often solves no-heat issues. DIY-friendly repair, typically 10-20 minutes.
Do-It-Yourself Stories from Customers like You
Would not heat Chris A. • Saint Joseph , IL • January 04, 2017
I figured there could only be a couple reasons why the dryer would not heat so I did some research. I read where you could test for continuity on the parts to determine which one was bad. A friend referred me to this site, I looked up the part for my particular model, ordered and replaced the part. It could not have been any easier. I will come back to this site with my future appliance parts needs for sure!
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP489483
The Screw is an OEM replacement part for Whirlpool appliances. The precise threads allow screws to join or assemble other parts securely.
Causes of a bad screw can include stripping, cracking, or loss of threads due to repeated installation/removal over time. Corrosion is also possible depending on environmental conditions.
Symptoms of a bad screw include:
- Loosened or detached components that were once fastened
- Reduced structural integrity of connections or assemblies
- Potential safety hazards if critical parts become dislodged
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Missing hinges to hold the door up Sandra C. • Gardena , CA • June 05, 2016
Found the parts in the diagram of my fridge and simply installed it very easy
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP307249
Fixes dryers that won't shut off, run too hot, or take too long to dry. This cycling thermostat regulates drum temperature. 15-minute DIY repair.
Do-It-Yourself Stories from Customers like You
Regular cycle did not work and air fluff didn't work Ronald R. • Jupiter , FL • March 15, 2018
Put both thermostats in as I did not know if the unit was cycling on high limit at times. Fixed both issues plus I used my lawn blower and blew all the lint out of dryer and short 3' hose. I also lubed rear drum bearings. Works like new. Ron R
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: W10857122
The Light Bulb is an OEM part for Whirlpool refrigerators. This part illuminates the water and ice dispenser area, providing visibility and ease of use, especially in low light conditions.
Over time, the light bulb can fail due to normal wear and tear, electrical surges, or damage from vibrations and impacts.
Symptoms of a bad light bulb include:
- The dispenser area not lighting up when activated
- Flickering or dim lighting
- The bulb failing to turn on consistently
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.
Do-It-Yourself Stories from Customers like You
My dryer was making noise James M. • Middletown , RI • September 19, 2014
I went on line and purchased all of the possible parts that could be worn out. I spent less than the service guy wanted to show up...The online videos were spot on. Two hours and it works like new! One of the best values on the Internet!
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP307250
Dryer runs but won't cycle off or cycles too frequently? A faulty cycling thermostat may be the cause. This common repair takes 30-45 minutes.
Do-It-Yourself Stories from Customers like You
Auto dry wouldn't shut off on maytag dryer Donald G. • Auburn , NY • September 11, 2017
Replaced timer and cycling thermostat. cycling thermostat was the problem. For some reason it wasn't getting the message to the timer needed to cycle the dial.
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3387137
This internal-bias thermostat regulates dryer drum temperature by cycling the heat on and off, helping maintain consistent drying performance and protect against overheating.
- Controls the cycling temperature of the heating circuit to prevent underheating or overheating
- Helps resolve symptoms like no heat, not enough heat, long dry times, or temperature swings
- A faulty thermostat may cause overheating that can trip the thermal fuse
- Located on the blower housing on many models
What's included: 1 internal-bias thermostat Install notes:
- Disconnect power and shut off gas (for gas dryers) before servicing
- Access the blower housing; note wire positions and transfer one at a time
- Mount the thermostat flush to the housing for proper sensing
- After installation, run a test cycle to verify proper heating
Do-It-Yourself Stories from Customers like You
Thermal fuse blew John P. • Palm Coast , FL • January 02, 2016
Cleaned exhaust duct, but only from the dryer/laundry room side. Replaced thermal fuse. Unit worked for about two loads and thermal fuse blew again. This time I cleaned the exhaust vent on the roof of my 2-story house. It was found to be partially obstructed and I was able to remove a significant amount of lint from it. Also, I researched the problem and followed someone's advice to replace the cycling thermostat together with the thermal fuse if the thermal fuse blows. So far it has been...
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP22001650
Secures components with constant tension to prevent looseness and vibration. Replace if broken, fatigued, or missing. Verify fit with your model number.
Do-It-Yourself Stories from Customers like You
Drum guides had worn out Robert S. • North Apollo , PA • October 08, 2014
Replaced them.
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10116756
Maintains proper spacing and alignment in your dryer's belt path. Replace if you hear squeaking or notice belt tracking issues. Verify fit with your model.
Do-It-Yourself Stories from Customers like You
The motor burned up after 28 years Robert M. • Paw Paw , MI • December 20, 2016
I replaced the motor and all other moving components along with the felt drum seals.drum glides and drive belt. The wiring instruction is where i had the most problems. Because my wiring had only 4 wires in the harness not 5, and one was a different color then the instructions call out, I believe was because it might have been and older model. the instruction called for a gray wire but mine was white with a blue piggy back wire attached. but after finding a few videos on line i figured that the...
Read more
More