Ldg89206aae Parts

Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.

Best Seller

Genuine Whirlpool part

E Ring

4.7 (47)

By: Whirlpool

Part Number: WP354987

The Idler Shaft Retaining Ring is an OEM replacement part for Whirlpool dryers. Also called an "E" ring, it is a sealing gasket positioned between the front and rear housing omponents. Maintaining an airtight seal prevents gas leakage and promotes efficient drying performance.

Causes of a bad retaining ring commonly involve compression loss of the rubber gasket material over many years of heating cycles. Exposure to petroleum-based cleaners may prematurely deteriorate the seal as well.

Symptoms of a failed 'E' ring include:

Gas leaks emitting foul odors around seams or vents
Reduced heat conductivity hampering dryer functioning
Moisture accumulation shortens fabric lifespan
Drafts compromising indoor air quality and energy bills

This OEM Whirlpool replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore gas dryer models.

This part fixes the following symptoms

Will not tumble

Do-It-Yourself Stories from Customers like You Loud squealing noise William B. • Rocky Mount , NC • December 17, 2018

First replaced the drum rollers...that wasn't it..took dryer back apart and spun the belt tension wheel by hand (should have done this the first time I took the dryer apart) and it squeaked. so I ordered the full parts: wheel, idler arm, idler spring, arm sleeve, E ring..Put it back together and whoa..no more squealing!! Read more

$11.95

Compare At:: $14.22
You Save:: $2.27

IN STOCK

Ships Monday Guaranteed

Add to Cart

Best Seller

Genuine Whirlpool part

Idler Pulley Arm

4.8 (30)

By: Whirlpool

Part Number: WP6-3033630

The Idler Pulley Arm is an OEM component specifically designed for Whirlpool brand clothes dryers. It pivots to lift belt tension and remove slack during dryer tumbling.

Symptoms of a problematic idler pulley arm include:

Drive belt slips off pulleys or tracks improperly
Reduced drying due to inefficient tumbling

Potential causes involve typical wear from extended usage. Seizing bushings or restrictive movement may diminish functionality over time as well.

This genuine OEM Whirlpool part is compatible with models including some brands produced by KitchenAid, Maytag, and Kenmore.

Do-It-Yourself Stories from Customers like You Clothes dryer had developed a loud squealing noise the problem turned out to be the idler pulley wheel Don F. • Bakersfield , CA • September 19, 2020

I removed the front panel of the dryer by removing 2 screws and lifting it up and out. Then I removed 4 screws from the bracket holding the tub in place. I had previously removed the 4 screws from the rear inspection cover so I reached in and released the spring loaded belt that turns the tub and then removed the idler pulley wheel. The tub just lifts out at that point, exposing the 2 Drum support rollers in the rear. I removed the 2 rear drum support rollers and decided to order 2 of... Read more

$54.36

Compare At:: $64.69
You Save:: $10.33

IN STOCK

Ships Monday Guaranteed

Add to Cart

Best Seller

Genuine Whirlpool part

Clamp

4.9 (51)

By: Whirlpool

Part Number: WP312967

The Clamp is an OEM part for Whirlpool dryers. This clamp ensures tight and secure connections within the dryer, particularly in securing ducts and vents that are essential for proper airflow and operation.

Clamps may need replacement due to loss of tension, corrosion, or damage from regular use. A compromised clamp can lead to operational issues such as prolonged drying times or excessive noise, resulting from loose parts or improper ventilation.

Symptoms of a bad Clamp include:

Loose or detached vents or hoses, leading to inefficient dryer operation.
Increased drying times, as a result of compromised airflow from unsecured ducts.
Unusual vibrations or noise, indicating that internal components may not be securely fastened.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This part fixes the following symptoms

No heat or not enough heat
Takes too long to dry
Noisy

Do-It-Yourself Stories from Customers like You Lack of heat and long drying times Allan H. • Baroda , MI • March 06, 2016

Our Maytag gas clothes dryer was not drying like it should/used to and was making a lot of noise. After researching online I figured the vent was partially blocked and/or the blower wheel was bad. When I took it apart, the vent had very little lint in the lower elbow exiting the back of the dryer but the blower wheel was loose on the shaft and was missing the clamp. I cleaned out the vent and put a hose clamp on the blower wheel to tighten it to the shaft and tried it again. The noise was... Read more

$11.95

Compare At:: $14.22
You Save:: $2.27

IN STOCK

Ships Monday Guaranteed

Add to Cart

Best Seller

Genuine Whirlpool part

Door Catch Kit

5.0 (22)

By: Whirlpool

Part Number: LA-1003

The Door Catch Kit is an OEM part for Whirlpool dryers. It includes the door catch and the necessary mounting hardware to secure it in place. This kit ensures the dryer door remains securely closed during operation, preventing heat loss and ensuring the appliance functions efficiently.

Causes of a bad door catch include regular wear and tear, physical damage, or misalignment of the door, which can impact the catch's ability to latch properly.

Symptoms of a bad door catch include:

The dryer door not staying closed
Difficulty latching the door shut
The dryer stopping mid-cycle due to the door opening

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This part fixes the following symptoms

Door won't close
Shuts off too soon
Doesn't shut off
Takes too long to dry

Do-It-Yourself Stories from Customers like You Door clip to my dryer broke Richard D. • North Dinwiddie , VA • March 15, 2014

Ordered a new clip and installed it. Easy to do. Unplugged the dryer. Removed the front. It is only held on by two screws. Removed wires to the door switch. removed the female end (it had the broken male piece in it. Inserted the new female part in the front, clipped in the male part into the door and reconnected the door switch wires, screwed the front back on. Job done. Total time was less than 10 minutes. Works like new. Read more

$24.95

Compare At:: $29.94
You Save:: $4.99

IN STOCK

Ships Monday Guaranteed

Add to Cart

Do you need help?

Get Questions Answered Instantly.

1-877-477-7278 Online

Live Help

Best Seller

Genuine Whirlpool part

Thermal Fuse

4.9 (15)

By: Whirlpool

Part Number: WP306604

The Thermal Fuse is an OEM replacement part for Whirlpool dryers. This safety device monitors and protects heating elements inside the dryer. If temperatures rise too high due to a blockage or other issue, the fuse automatically opens the electrical circuit to cease further heating.

Symptoms of a bad thermal fuse include:

Dryer failing to heat or stay warm during cycles
Fluctuating or inconsistent heat levels
Tripped circuit breakers after drying

Causes of failure involve wear or damage from years of high heat exposure. Over time, components become brittle and less responsive.

This OEM Whirlpool replacement is also compatible with some Kenmore, Admiral, Roper, and Estate dryer models.

This part fixes the following symptoms

Won't start
No heat or not enough heat

Do-It-Yourself Stories from Customers like You Maytag gas dryer was not heating Christopher P. • Los Angeles , CA • October 04, 2014

Did some dryer repair research (dryer not heating) on the internet. Bought an ohm meter, opened up the dryer and tested the cut-off-T, high limit thermostat, dryer igniter, flame sensor, cycling thermostat for continuity. The igniter was bad, the other parts tested ok. Went online to AppliancePartsPros.com searched for a new igniter for my specific dryer model, found the right replacement igniter and watched the video on how to replace the igniter. Because my dryer is old (15+ years) and I... Read more

$28.95

Compare At:: $34.45
You Save:: $5.50

IN STOCK

Ships Monday Guaranteed

Add to Cart

Best Seller

Genuine Whirlpool part

Screw

4.6 (7)

By: Whirlpool

Part Number: WP90767

The Whirlpool screw is an OEM replacement part responsible for securing various components or parts on different types of Whirlpool appliances. The screw is designed to provide a secure and reliable fastening connection, ensuring that different parts of the appliance stay in place. It is commonly used in different locations within the appliance, such as the cabinet, panels, or other structural elements.

This part fixes the following symptoms:

Loose or wobbly components within the appliance
Panels or parts that are not securely attached
Rattling or unusual noises due to loose parts
Damaged or missing screw

The Whirlpool screw can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

Do-It-Yourself Stories from Customers like You Certain buttons were'not working Brent T. • Easton , MD • November 17, 2014

One day my wife went to bake something and the bake/broil buttons as well as #3, #9, and oven light ceased to work. Local repair guy came by and wanted to charge $500 to fix it....YEAH RIGHT! Did a little homework and found this website, spoke with knowledgable staff who pointed me in the right direction. Took me all of about 20 minutes to install new control panel..everything works perfect...THANKS! p.s. In doing my research come to find Maytag did little to insulate control panel from oven... Read more

$7.95

Compare At:: $9.46
You Save:: $1.51

IN STOCK

Ships Monday Guaranteed

Add to Cart

Best Seller

Genuine Whirlpool part

Hex Nut

4.9 (20)

By: Whirlpool

Part Number: WP33001443

This Hex Nut is a small but critical fastener used to secure brackets, panels, and internal assemblies in your appliance. Replacing a stripped, corroded, or missing nut restores a tight, rattle-free, and safe installation.

Threads onto a matching bolt or stud to clamp parts together
Helps maintain alignment and reduce vibration-related loosening
Commonly used on panels, brackets, supports, and internal assemblies
Replace when threads are damaged, hex flats are rounded, or hardware is missing
Symptoms can include loose or rattling components or hardware that won't stay tight

What's included: One hex nut. Install notes:

Disconnect power and, if applicable, shut off gas or water before servicing
Use the correct-size nut driver or wrench to avoid rounding the hex
Start the nut by hand to prevent cross-threading; tighten snugly without over-torquing
Inspect and replace any damaged mating bolt/stud or washer for a secure repair

Do-It-Yourself Stories from Customers like You The rollers needed to be replaced, the axles for the rollers needed to be replaced, the tension pulley roller needed to be replaced, the belt needed to be replaced Richard G. • El Paso , TX • December 18, 2018

It took me about 2 hours to take everything apart and get it back together & running again with no problems. All the parts I ordered were exactly what I needed to fix everything. Thank you all !!! Read more

$5.95

Compare At:: $7.08
You Save:: $1.13

IN STOCK

Ships Monday Guaranteed

Add to Cart

Best Seller

Genuine Whirlpool part

Light Bulb

4.7 (21)

By: Whirlpool

Part Number: W10857122

The Light Bulb is an OEM part for Whirlpool refrigerators. This part illuminates the water and ice dispenser area, providing visibility and ease of use, especially in low light conditions.

Over time, the light bulb can fail due to normal wear and tear, electrical surges, or damage from vibrations and impacts.

Symptoms of a bad light bulb include:

The dispenser area not lighting up when activated
Flickering or dim lighting
The bulb failing to turn on consistently

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Do-It-Yourself Stories from Customers like You My dryer was making noise James M. • Middletown , RI • September 19, 2014

I went on line and purchased all of the possible parts that could be worn out. I spent less than the service guy wanted to show up...The online videos were spot on. Two hours and it works like new! One of the best values on the Internet! Read more

$13.47

Compare At:: $16.03
You Save:: $2.56

IN STOCK

Ships Monday Guaranteed

Add to Cart

Best Seller

Genuine Whirlpool part

Screw, 1 Piece

4.6 (13)

By: Whirlpool

Part Number: WPY014874

This factory fastener secures appliance components such as panels, brackets, and trim. Replacing a missing or stripped screw restores a tight fit, reduces rattling, and helps keep assemblies aligned for reliable performance.

Fastens appliance parts to maintain structural integrity and alignment
Helps address symptoms like loose or vibrating panels, gaps, or hardware that won't stay tight
Replaces lost, damaged, or corroded fasteners during repairs or reassembly
OEM-matched thread and fit for the specified location

What's included: 1 screw Install notes:

Disconnect power; shut off gas or water supplies before servicing
Replace one screw at a time to preserve alignment of parts
Start threads by hand to avoid cross-threading; tighten snugly without over-torquing
Use the correct driver size/type specified for your model

Do-It-Yourself Stories from Customers like You Loud squealing noise William B. • Rocky Mount , NC • December 17, 2018

$5.95

Compare At:: $7.14
You Save:: $1.19

IN STOCK

Ships Monday Guaranteed

Add to Cart

Best Seller

Genuine Whirlpool part

Lp Gas Conversion Kit

4.8 (9)

By: Whirlpool

Part Number: MAL9000AXX

The LP Gas Conversion Kit is an OEM part for Whirlpool appliances. This kit allows for the conversion of natural gas appliances to use liquid propane (LP) gas. It includes all necessary components, such as orifices and instructions, to ensure a safe and efficient conversion.

Over time or due to specific needs, you might need to convert your appliance from natural gas to LP gas. Causes for needing this conversion include moving to an area where only LP gas is available or preferring LP gas due to its efficiency and environmental benefits.

Symptoms indicating the need for a gas conversion kit include:

Moving to a location that only supplies LP gas
Changing energy preferences for better efficiency
Appliances set up for natural gas needing adaptation to LP gas

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Do-It-Yourself Stories from Customers like You I changed my dryer from ng to lp Dave F. • Kimbolton , OH • June 06, 2015

The kit was very simple it took longer to take the dryer apart than it did to do the change over and it works great thank you for you're product Read more

$46.95

Compare At:: $55.40
You Save:: $8.45

IN STOCK

Ships Monday Guaranteed

Add to Cart

Best Seller

Genuine Whirlpool part

Dryer Gas Valve

4.8 (11)

By: Whirlpool

Part Number: WP306176

This gas valve includes the coils. For the coils alone use part number 279834

Do-It-Yourself Stories from Customers like You Gas valve on gas dryer leaking Thomas R. • Stillwater , MN • January 10, 2017

Replaced valve had some trouble removing the fitting from the valve as the new fitting was slightly too large and had to be replaced with the fitting from the old valve. Used a large crescent wrench to grip the valve at the base and I was able to apply enough force to remove both fittings transferring old fitting to new valve. The instructions were detailed and excellent. The dryer is up and running fine. Read more

$207.52

Compare At:: $244.87
You Save:: $37.35

IN STOCK

Ships Monday Guaranteed

Add to Cart

Best Seller

Genuine Whirlpool part

Spring Fastener (Retaining Clip)

5.0 (6)

By: Whirlpool

Part Number: WP22001650

This spring fastener applies constant tension to hold a component securely in place inside your appliance, helping prevent looseness, vibration, or gaps. Replacing a fatigued or missing clip restores a tight, reliable fit.

Provides spring tension to clamp and retain a part, seal, or panel
Helps maintain alignment and reduce vibration or rattling
Restores secure attachment when the original clip is bent, stretched, or missing
Symptoms can include a part not staying put, visible looseness, or a clip that's damaged or gone

What's included: 1 spring fastener Install notes:

Disconnect power; turn off water supply if applicable
Use needle-nose pliers or a suitable spring tool; wear gloves and eye protection
Note the original orientation before removal to ensure proper reinstallation
Make sure the mating part or seal is fully seated and the fastener is fully engaged before reassembly

This part fixes the following symptoms

Noisy

Do-It-Yourself Stories from Customers like You Drum guides had worn out Robert S. • North Apollo , PA • October 08, 2014

Replaced them. Read more

$10.43

Compare At:: $12.52
You Save:: $2.09

IN STOCK

Ships Monday Guaranteed

Add to Cart

Shop With Confidence

Over 15 million customers served!

365-Day Returns

Hassle-free Returns

Fast Delivery

1.7 Days on Average!

Free Tech Support

On all purchased parts!

Genuine Whirlpool part

Idler Bracket Spacer (Dryer)

4.9 (9)

By: Whirlpool

Part Number: WPW10116756

This idler bracket spacer sits on the idler arm pivot to maintain proper spacing and alignment in the dryer belt path. Replacing a worn spacer can quiet squeaks and help the drum belt track and tension correctly.

Maintains correct spacing of the idler bracket on its pivot to prevent side-to-side play
Helps keep the drive belt aligned on the idler pulley for consistent tension
Replace if cracked, worn, or missing; possible symptoms include squealing/chirping, belt rubbing or fraying, belt coming off, or intermittent drum rotation
Useful check: the idler arm feels loose or wobbly, the spacer may be worn

What's included: 1 idler bracket spacer Install notes:

Disconnect power; turn off gas supply if applicable, and wear gloves
Access the belt and idler assembly; release belt tension and remove the idler bracket
Note the spacer's orientation; install the new spacer on the pivot and re-route the belt correctly
Hand-rotate the drum to ensure smooth belt tracking before reassembly and power-up

Do-It-Yourself Stories from Customers like You The motor burned up after 28 years Robert M. • Paw Paw , MI • December 20, 2016

I replaced the motor and all other moving components along with the felt drum seals.drum glides and drive belt. The wiring instruction is where i had the most problems. Because my wiring had only 4 wires in the harness not 5, and one was a different color then the instructions call out, I believe was because it might have been and older model. the instruction called for a gray wire but mine was white with a blue piggy back wire attached. but after finding a few videos on line i figured that the... Read more

$31.95

Compare At:: $37.70
You Save:: $5.75

IN STOCK

Ships Monday Guaranteed

Add to Cart

Genuine Whirlpool part

Blower Seal

4.5 (6)

By: Whirlpool

Part Number: WPY312901

This blower seal sits between blower housing components to prevent air leaks, helping direct all exhaust air through the drum and vent. Replacing a worn seal can help restore proper airflow and drying performance. What it does:

Forms an airtight gasket between the blower housing and its cover/duct
Helps maintain correct airflow and temperature balance through the drum and exhaust
Reduces lint and dust escaping into the cabinet
Common failure symptoms: longer dry times, weak vent airflow, whistling or rattling from air leaks

What's included:

1 blower seal

Install notes:

Disconnect power and, for gas dryers, shut off gas before servicing
Access the blower housing; remove the old seal and clean mating surfaces of lint and residue
Position the new seal flat and even; reassemble without pinching or deforming the gasket
After reassembly, verify strong exhaust airflow and check for leaks

Do-It-Yourself Stories from Customers like You Making loud squealing sound when dryer was turned on Michael M. • Plainfield , IL • November 19, 2018

Took the front panel off (the door front), disconnected the connector to the door switch and used a wooden clothespin to bypass the door switch. Turned on the dryer to locate loud squeaking sound and found it was coming from the motor area. When I started to take the blower section apart from the motor, that is when I saw the "blower wheel" slipped off the motor shaft. The blower wheel has a "C" clip retainer and compression ring to keep it snug on the motor shaft (but it was loose). Now I... Read more

$44.95

Compare At:: $53.04
You Save:: $8.09

IN STOCK

Ships Monday Guaranteed

Add to Cart

Genuine Whirlpool part

Rubber Foot

5.0 (1)

By: Whirlpool

Part Number: WPY314137

The rubber foot is an OEM replacement part for Whirlpool washing machines. This small but essential component fits beneath the leveling legs, providing stability and preventing the appliance from moving or vibrating excessively during operation. It also protects flooring surfaces from potential scratches or damage.

Symptoms of a bad Leveling Leg Pad include:

Increased vibration or noise during the wash or spin cycle
The washing machine wobbling or becoming unsteady
Visible wear, cracks, or damage to the pad

Causes of a failing Leveling Leg Pad can include wear and tear from prolonged use, exposure to moisture, or excessive weight causing deformation. Replacing worn pads helps maintain the appliance's balance and efficiency.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

For the leveling leg order W10176519.

Do-It-Yourself Stories from Customers like You Unlevel and shaking moving out of position cracked dryer igniter Steven B. • Grantsville , WV • April 26, 2016

Replaced dried crumbling rubber foot. Cleaned inside and outside of dryer before installing igniter cleared vent hose. Leveled unit installed dryer igniter. Fired it up.Runs Great Now. Read more

$6.95

Compare At:: $8.34
You Save:: $1.39

IN STOCK

Ships Monday Guaranteed

Add to Cart

Genuine Whirlpool part

Burner Assembly (Gas Dryer)

4.9 (14)

By: Whirlpool

Part Number: WP33002793

This burner assembly is the gas/air mixing and flame head for gas dryers. Replacing a warped or corroded burner restores reliable ignition and steady heat so loads dry evenly and cycle times return to normal.

Mixes incoming gas with air and directs it to the igniter for proper light-off
Produces a stable flame to heat the dryer's airflow
Replaces burners that are bent, rusted, or clogged and affecting ignition
Typical symptoms: no heat, burner won't light, intermittent heat, or long dry times

What's included: One burner assembly. Install notes:

Disconnect power, shut off gas, and allow the dryer to cool before servicing.
Access the burner compartment; note component positions and wiring for reassembly.
Protect the igniter and sensor mounted near the burner from impact.
After reassembly, restore gas and check all connections with a leak-detection solution; verify proper ignition and flame.

Do-It-Yourself Stories from Customers like You First look 2nd look 3rd look success!!!!! Kirk P. • Des Moines , IA • October 10, 2014

When I first looked at my dryer I thought it was my ignitor, on a closer look I found that about an inch of my burner assembly arm was laying in a corroded mess on the bottom pan of my dryer. I came online and found your website. After reviewing your parts I thought well I can probably get those local and with competive pricing. Wrong!! There are 3 appliance parts stores withing about 3 miles and I checked them all. Higher prices by 25-35% and longer wait times than your advertised... Read more

$102.65

Compare At:: $123.18
You Save:: $20.53

IN STOCK

Ships Monday Guaranteed

Add to Cart

Appliance

Appliance

Lawn & Garden

Need help finding dishwasher parts?

Need help finding dishwasher parts?

Need help finding dishwasher parts?

Ldg89206aae Parts

E Ring

Idler Pulley Arm

Clamp

Door Catch Kit

Thermal Fuse

Screw

Hex Nut

Light Bulb

Screw, 1 Piece

Lp Gas Conversion Kit

Dryer Gas Valve

Spring Fastener (Retaining Clip)

Idler Bracket Spacer (Dryer)

Blower Seal

Rubber Foot

Burner Assembly (Gas Dryer)