Hardware Hand Small Engine Safety Switch Parts

Secured the inner and outer door together and screwed handle back in place. Read more

I was able to clean the Oven Temp Sensor with 99% alcohol. Then replaced All switches (after breaker was isolated). Put it all back the way I found it. Turned on breaker. Tested all functions and had no reports of Fan Code re-appearing since. Read more

Ordered the right part, took the back off the top control panel, and popped it in. Read more

Replaced two switches that controlled two front burners. One controlled three different burner sizes options in one burner. The other was the speed burner, basically three different burner options in one burner. Read more

• Won't start

I was searching the web for solutions and came across two folks who had similar trouble code. One fixed his by removing the pump strainer from the pump to find coins blocking water flow, thus the analog water pressure sensor provided a failure response. My issue was solved by following the other hints I got. I ordered a new sensor (switch). It was expensive for what it is, but the washer will not run correctly without it! The part arrived in a very timely manner, and it was the right part.... Read more

First and foremost, don't believe everything you see on Youtube. In order to get to the gas solenoid that feeds the burner you MUST take the entire top off that side of the range. Remove the grates and burner tops. You will see 2x 20mm brass nut, or so it appears, that hold each burner in place on the splash/drip pan. It is not just a nut, it is a venturi that threads down into what is called the jet holder. You may get a socket on it and think you are getting it loose but, more than likely you... Read more

Start by removing the frame on the sides and bottom of the door. (Do not unscrew the corner screw holding the side frame and bottom together.) Be careful the glass will fall once the last screw is removed from the bottom so hold tight. Carefully remove glass and set aside. Remove top frame that held the handle. Once all the frame work and outer glass is removed unscrew the bracket that held the door handle from the door. Taking the top frame and bracket insert screw and washer and screw the... Read more

Searched internet for answers. Decided to replace the door switch. Drier now runs great! Read more

Initially performed troubleshooting over the phone with Bosch customer support and did preliminary research on the web. Ultimately had to call out service technician to isolate/confirm problem. He confirmed the problem was most likely the switch (if not, the actually computer processor) and gave me the part number (since it was going to take 10 BD's for him to get the part). I ordered through Appliance Parts Pros and received the part in only 2 days. However, upon trying to install it, I... Read more

Removed fill level pressure switch knob. Removed three screws from the back of the control panel.Opened the control panel and removed electrical connector and plastic tube from the pressure switch. Removed and replaced pressure switch. Placed control panel to correct position and replaced the three screws. Read more

Simple unplug, unscrew and replace. Read more

So I ordered the burner and Ithe switch because I wasn't sure what part was defective. I pulled the oven out and I removed the 6 1/4 inch screws on each side of the glass top as well as the 2 Phillips head screws on the back, removing the 2 1/4 screws on the shield on the back gIves you easier access to them, then lifted the glass top up on the front to access the switch and burners. Make sure you turn the power off before beginning this process. When lifted up the wires connected to the... Read more

I had to pull and clean the pressure sensor switch four times in a year. Each time more gunk accumulated. When that happens the sensor does not close the water valve. The dishawsher keeps filling and the water comes out through the overfill port. The water then goes in the catch basin under the washer and floats the emergency switch. This cuts off the water but keeps the pump running just in case. Tripping the circuit breaker is only a temp fix. What happens is the water level may have... Read more

I replaced the switch Read more

• Light not working
• Not dispensing water
• Ice maker not making ice

Ordered 2 light switches and replaced them. Read more

I replaced the assembly behind the water level knob. I watched the video on appliancepartspros.com before starting, and then watched it again in short portions while going thru the repair process. Read more