Range/Range/Oven Surface Element Board Parts

Replaced timer, thermostat, a thermal fuse, the pair of thermal cutoff switches and finally the heater element. Hard to say what the final fix was that did the trick -- I am guessing it was the heater element although the old one appeared to have good continuity. All praise goes to the on line chat Pros Erica B and Robin C that took considerable amount of time and effort to help me decipher the problem. For that alone, Appliance Parts Pros will be my go to source for appliance parts for the... Read more

I took off the front cover and checked the sensors which were all good. Then I removed the cover for the heating coil after finding that it appeared open. Found that the coil had in fact broken but the break was not visible just by looking in. Located the break in the coil within an insulator near the back. I checked appliance stores locally and found the coil for far more than Appliance Parts Pros wanted for it. I placed an order after chatting with a tech, I placed and order and had it in... Read more

Replace defrost timer Read more

Put in a new 6" surface burner. Read more

First I called the local retailer to ask about a non-warranty service. Minimum $100 charge. Figured I would take a shot at the repair as I had fixed the fridge once before. I used a digital thermometer to verify that the temperature in the ice maker compartment was at the right temperature. I put the ice maker in diagnostic mode to eject the ice that was sitting in the ice tray (turn off and on and then push the ice full lever three times). Ice was successfully ejected. Sometimes the ice... Read more

• Little to no heat when broiling

I have had this oven for 40+ years. It is an enamel oven, something that you can no longer buy. Because I did not wish to buy new, I decided to service it myself and searched for the parts I needed. AppliancePartsPros.com was the only site to offer all three parts, so many having been discontinued by other providers. I replaced the oven gasket, the broiler element & the lens without any difficulty. I have replaced the bake element previously as well. I am very grateful that I was able to keep... Read more

Replaced electronic control board and everything is back to working normally. Read more

Replaced defective/worn surface unit and burnt receptacle! Read more

Replaced timer. It's a snap in place timer, once you remove the defective timer, overall pretty easy. Read more

Turn off the water to the ice maker. Unload the freezer and remove the freezer door so you have room to work. Remove the ice maker by removing 2 screws in the front then pull the unit toward the front and unplug the wiring connection. The pipe will now be exposed. Remove the flexible piece from the front of the pipe that directs the water flow to the ice cube tray. Remove the wire tie on the front of the pipe and peel off the insulation surrounding the pipe. The heater will now be exposed.... Read more

• Little to no heat when broiling

Pulled stove out from wall and unplugged for safety, removed back cover to check for any wire damage because the element blew out pretty bad but wiring was ok, removed wires from broil element at the back of the stove. Went to the front of the stove opened door and removed hangers and finally the element screws on broil element. I also unwired removed the bottom element to clean the inside of the oven with soap and water because the whole inside of the oven was cover in a light white coat of... Read more

• Little to no heat when broiling
• Element will not heat

I ordered the replacement part; after it arrived, I turned off the power to the oven - watched the video on how to replace the part, which was fantastic as it told me to make sure when I disconnect the old element not to let the wires fall behind the oven (that would have been a big problem b/c it's a wall oven) - However, one wire still slipped back a little - so I used needle nose pliers to retrieve it. Was able to plug the new one in - screw it into place with the original screws. I made... Read more

Replaced the machine control board and user interface. Read more

Replace control/switch panel along with exterior push button panel. Read more

• Won't start

Replaced the Inverter box Read more

• Little to no heat when broiling

I needed to replace the oven broil element on my 15 year old GE range/oven unit. The broil element was broken in half during an oven self-cleaning cycle. Due to the age of the oven, I decided to replace both the broil and bake elements. I ordered the elements from Appliance Parts Pro. Their web site made it very easy to identify and locate the correct replacement parts. The parts arrived in 2 days. I watched the repair demo videos available for each element. Although the oven used in the demo... Read more