Steven A Commack , NY July 01, 2021 Appliance: General Electric Refrigerator PFSS5RKZASS The ice maker was filling the ice bucket very slowly (about 25% 50% normal rate). First I called the local retailer to ask about a non-warranty service. Minimum $100 charge. Figured I would take a shot at the repair as I had fixed the fridge once before. I used a digital thermometer to verify that the temperature in the ice maker compartment was at the right temperature. I put the ice maker in diagnostic mode to eject the ice that was sitting in the ice tray (turn off and on and then push the ice full lever three times). Ice was successfully ejected. Sometimes the ice was only partially frozen. Also tried running a hairdryer on hot to thaw any blockage in the air conduit to the ice maker compartment. It seemed like things were just working marginally. So it wasn't the ice maker motor, and changing the temperature sensor did not seem like a solution either. So I took an educated guess that something was marginal with the controller board. FYI, this is my second controller board for this fridge now going on 10 years old. I had heard some fan motor rev'ing sounds earlier in the year. That sound went away which meant either it got better or failed completely. Note that I had the same problem with the previous controller board that I had replaced in this fridge about 5 years ago. I ordered the replacement board from AppliancePartsPros - they offered a competitive price. Note - some other vendor sites showed significantly lower-priced alternatives that turned out to be not for my model - be careful. Appliance Parts Pros shipment came in a couple of days. I changed the controller board - took about 15 minutes. The ice maker is now working like new. Read More... Do-It-Yourself Rating: Repair Time Estimate: Less than 15 minutes Tools: Nut Drivers, Pliers
John R Chesterfield , MI July 24, 2015 Appliance: General Electric Refrigerator PFSS5RKZASS My refrigerator stopped cooling and the lights on the front panel were flashing I replaced the control board myself. I was told by the repair guy that the part was $550 and would take two weeks to receive because there was a back order on this part. I ordered this part from you and had it overnighted for a total of $188 including overnight shipping. The delivery was so fast I didn't even have to empty my freezer! It only took me ten minuets to replace! This company is as good as it gets folks. Thank you! John. Read More... 23 People found this story helpful Do-It-Yourself Rating: Repair Time Estimate: Less than 15 minutes Tools: Nut Drivers, Pliers
Robert E Crofton , MD March 16, 2015 Appliance: General Electric Refrigerator PFSS5RKZASS Ge profile fridge stopped working lights flashed briefly on the panel when i unplugged/plugged it back in and made brief clicking noise then nothing Swapped out the main control board. Read More... 12 People found this story helpful Do-It-Yourself Rating: Repair Time Estimate: Less than 15 minutes Tools: Pliers, Screwdrivers
Curtus S Lakeville , MN June 04, 2016 Appliance: General Electric Refrigerator PGSS5RKZCSS Interior lights not working water despenser ice maker etc exterior lights flashing would keep cool and freezer working New mother board Read More... 7 People found this story helpful Do-It-Yourself Rating: Repair Time Estimate: Less than 15 minutes Tools: Nut Drivers, Screwdrivers
Joe P Jackson , NJ November 19, 2019 Appliance: Model PFSS5RKZH-SS GE profile refrigerator was dead no lights or anything I called GE for repair and they told me the earliest they could repair the refrigerator would be a week away. It was dead, no lights or sounds. I looked online for hints and found that there are only a couple of items that would cause it to be totally dead. The wall outlet was working, the line cord to the fridge had 120 volts at the end. So I followed the wires to the Mainboard and found it was getting 120 volts at the power input to the board. So I took a shot and ordered the board. It was here the next day. Unplugged the fridge and carefully replaced it and poof all is well. Oh BTW, vacuum out the air intake around the condenser coil. It was clogged with dust. Read More... 6 People found this story helpful Do-It-Yourself Rating: Repair Time Estimate: 15-30 minutes Tools: Nut Drivers