User Control Display Board Parts

The basin would fill but would not agitate, there was no sound, no grinding noises, no sound of a motor running without agitation due to a broken belt. The basin full of water was able to drain if I advanced the timer to Spin. By playing around with the timer dial further, I could get every function of the washer to operate, at least partially. So, that said electrical problem to me. I assumed the trouble was either the safety switch at the back of the lid or the timer mechanism. Tested... Read more

I first tested and replaced the temperature sensor. Since this is a slide-in range, I managed to pull it out just enough to access the back without disconnecting the downdraft and gas line. (For wall models this would not be the case.) Unfortunately, that did not do it. Next I replaced the lower heating element because it was a little below the ohms level it should be at. No go. So far, both of these were pretty easy to do and were relatively inexpensive so I wasn't too frustrated. Then I... Read more

• Freezer not defrosting

I had had the same problem 4 or 5 years ago and spent close to $200 to repair it. I did have the slip from that repair with part #'s so I went ahead and ordered a defrost timer and thermostat. You-tube had plenty of videos on replacing those parts and even before they arrived I was able to add a switch and bypass the broken thermostat and start a cycle manually with the timer. (which it seems was was still functional). Between that and cycling some ice packs up from the still working... Read more

Turn off power to machine, Take off door panel - 12 screws. hold up door panel a bit and make sure to remove the ribbon from the touch pad to the control module (use some pliers to rock it out of the board). Since I was changing the Module, I just removed the 1 screw that held it in place and it gave me some more room to get my hands in there and remove all the wiring freeing up the board to remove the touch pad ribbon last (I didn't want to tear it because I was not replacing it and after 9... Read more

Ordered the part from Appliance Part Pros. It came in one day! Had to disconnect the gas line and wrestle the unit out of the wall cabinet, but the repair was easy and straightforward. The job took less than an hour Read more

Replaced new motherboard and face plate. Read more

It's very easy fix. If your unit flashing e2 f2. It's your relay board take screw if on door couple latched s on the gray relay box pull wires harness of slow. Re install the same way it came of Just remember to cut the power off first . Leave your door open when re powering unit. Read more

I replaced the main control unit Read more

So initial thought was bad bake igniter. I'bve replaced this before so I replaced it again and it wouldn't glow. Checked broil igniter and same thing, no glow. Checked voltage at molex connector for bake igniter and it went from 6.6v to 3.4v when triggered to glow -- well below the 120v expected. Ordered new clock/controller and overlay -- it shipped the next business day! Removed a handful of screws from the back panel to expose the clock/controller and removed/ replaced it with new... Read more

Replaced UI console Read more

I don’t think I needed the capacitor and relay, but while I was at it I figured I would. Originally we found we had an issue when water cane out of the ice maker. The freezer was hovering around freezing and the refrigerator was about 33 deg. I unplugged the refrigerator and it came back on and ran about a day. The next night, same thing. This time cycling power did not seem to help. Removing the rear cover where the control board was and moving it around allowed it to turn on next time I... Read more

Replaced the thermostat Read more

• Fridge too warm
• Won't start

Replace the thermostat kit. Watched a video on youtube and followed directions! So EASY!! Paid a repairman $250+ to replace the thermostat a couple of years ago. BTW - This repair was made by a woman - who says only guys can fix things!!! Read more

My experience could not have been smoother. I called the repair guy just to see how much money I saved and I was shocked! I saved $123.00, thanks to appliance parts pro. Thank you so very much for your professional help, great prices & super fast shipping! From now on, when another appliance needs repair I'm going to you guys first. I'm spreading the word to every single person I know and posting it on social media as well. Thanks again, Jeremy Read more

I tested all electrical parts. and found the thermostat was not working. I ordered one . replaced it .it works as good as new. Read more