Module Parts

I noticed that the bottom of the plastic bucket was cracked even though it was less than two years old. I called Samsung and they wanted to charge me almost $200. Instead, I found the part at appliance parts pros for half that cost. Since I replaced the ice tray bucket assembly, my ice maker is working perfectly! Read more

• Ice maker dispenses too little ice

This was a little more involved than I originally thought, but after watching the video on the site it wasn't so bad. They walk you through each step verbally and visibly so you can see exactly what to do. Replacing the auger took around 20 minutes, and only that long because the screw holding the ice shield was a bit tough to turn. I just applied gentle pressure and turned slowly until it became loose. The rest was fairly easy, but I did get a small cut from the ice crusher blades. Nothing... Read more

I removed the old ice maker and installed a new one, along with changing the air and water filters. Read more

I watched the video that you provided and the repair went very smoothly. The video was specific to the exact part that I purchased. Great instruction and easy repair! Read more

• Ice maker dispenses too much ice
• Ice maker not making ice

Since I could not find the correct thermistor from the schematic provided, I ordered the thermistor harness for the evaporator. I cut the harness and spliced it to the sheared thermistor wires on the roof of the freezer compartment. It now works fine with a little "farmer ingenuity" help. Samsung was absolutely no help at all, but the guy that I spoke with over the phone at APP sure was. This site is now my "go to" for appliance parts! Tip for others with this model. Do not overfill the upper... Read more

This was easier then I made it. Originally took the actual ice maker out without removing the whole system from the door. There are 3 silver screws that do that hold the whole mechanism in place, as opposed to the 5 white screws that hold the ice maker in place. With the entire assembly out it was a matter of routing the ground wire, retaping the wires, and then the whole assembly went back into the door without a problem. Need a phillips and a flat screwdriver, I also found a needle nose... Read more

The control went thru a month or so of erratic behavior; the display would come on and flash and beep without any input on my part. Then it died completely. I did a little research on the GE website and determined likely cause waa a defective user interface board. I found AppliancePartsPros.com and contacted their tech support, who directed me to check the output of the control board across 2 pins for 13.5v DC. I did this, and measured 13.8v, so control board was good. When I reconnected the... Read more

Just bought the whole assembly and slid it in. Read more

• Ice maker dispenses too much ice

Replaced ice maker. Some confusion as to which part # it was as the model number cross reference shows the one I purchased was not for my model refrigerator when it actually was. Secondly, a few comments from others said the switch out was simple. Only 3 screws holding in the ice maker although one of the three was in a tight spot . That is technically true. Three screws do hold the ice maker on the door , however, you must also remove the door panel behind the ice maker to get to the wiring... Read more

I took apart the old bucket with a screwdriver and put the new one with no problems. Read more

After ordering the part, I first watched the video several times. Then I placed my phone on my workspace so that I could start and stop the video when following the step-by-step instructions. Then I shut down the refrigerator circuit breaker while I removed the ice container and full ice maker components. I then closed the refrigerator doors to keep the cold air in. I kept starting and stopping the video as I went, as I unplugged wiring components, connection jumpers, the ice maker shutoff... Read more

• Ice maker dispenses too much ice

This appears to be a weak spot on these refrigerators; the left-door ice maker will stop making (or at least consistently making) ice. Instead, an ice dam is created, which builds up in the ice maker corridor, making even getting the slide-in bucket nearly impossible to remove. The ice also freezes up the ice making tray, which therefore cannot drop the ice cubes. Generally, two things may go wrong which lead to this issue. The first is the ice-making assembly; its electrical components... Read more

Replaced the control board on bottom of machine Read more

• Ice maker won't dispense ice
• Ice maker not making ice

After finding out the cost that we would have to pay for the repair locally, I went to Appliance parts pro.com. with the intention of finding out the cost for parts. We had been quoted $100 for the first hour which included repair if it could be done under the first hour plus parts. And they added that the typical repair for the ice maker was between $200 and $500. Fortunately we are very organized and had the original paperwork of the refrigerator which has all parts and numbers for the... Read more

• Ice maker dispenses too little ice

When I first searched the AppliancePartsPros.com site for my specific model, the ice maker that appeared in the parts list was not for my refrigerator. So, I bought one from one of your competitors. It arrived and worked but produced ice even more slowly than my original unit, albeit at 0F. So, I went back to AppliancePartsPros.com parts list and browsed completely through it only to find another ice maker that did match mine. It was almost twice the cost, but after installing it, worked... Read more

First I watched Youtubes and decided it was the lower control board, ordered it from Appliance Parts Pros, and got it within 2 days. Installed it and no change. Called Appliance Parts Pros to repair the help line and they were very helpful told me I needed the upper board (UI) so I ordered it got it also in 2 days installed it and everything works perfectly. Appliance Parts Pros is very helpful and prompt in shipping. Highly recommend. Read more