Hardware Hand Small Engine Safety Switch Parts

• Will not fill with water

Replacing the inlet valve solved the problem. The old valve was somehow clogged with white sediment. I probably could have taken it off and cleaned it out if I'd known, but replacing the valve was much easier. Took about half an hour to repair. Video walk through was extremely helpful. Great to have a working dishwasher again! Read more

First, I modified old butter knife by bending a 90° angle about 3/4" from the tip. I slid the bent in up under the bottom of the switch cover and worked it to one side. I then rotated the knife downward using the bent end to pry the cover off. The switch is held by plastic arms on each side. The bottom right arm has a locating pin that fits into the switch. Unplugged the switch and re-installed. Read more

• Will not fill with water
• Will not stop filling with water

Hmm...watched video after reading on web of running water problem with GE washer....common fail .....moving stuff to get to the washer took all the time, easy fix but a lot of screws to remove and looking time APP site very good, will order again if need be thanks Read more

• Element will not heat

We cut the power, took the control panel off, got the burner switch number from the original part, and ordered a new one. We were a little worried at that point, because your website offered a "replacement" part, with a different number than the original. However, we put the model number into your double check feature and were assured that we were getting the right part. The part arrived in two days and frankly we were still worried, because the new part was slightly larger than the original.... Read more

Put in a new infinite switch behind the knob to control temp level. Read more

I was getting really frustrated with our oven. It would preheat to the correct temperature, then slowly lose heat until it was down to about 200 degrees. So it took about two hours to heat a pizza! Finally decided to repair the oven myself, rather than pay $300.00 to have a repair person come out. Ordered the replacement igniter from AppliancePartsPros.com, and it arrived in two days. I followed the instructional video on the AppliancePartsPros.com website, and it was going well until I... Read more

• overflowing
• Will not fill with water

I checked continuity at the float switch since I knew the inlet valve was working when direct wired to 120v. Switch did not have continuity. Replaced switch and inlet valve worked at start of cycle. Read more

Plug and play minus a few screws to remove, simple repair. Read more

An online search of the problem (would not agitate or spin) indicated a bad lid switch. Then with model number was able to find an online video on how to change it. Next I opened the washer, like in the video (very easy) and made sure that the lid switch looked like the one I ordered from AppliancePartsPros.com. Of course with the model number it was easy to find the right part. The part arrived in 2 days with no special shipping. What great service! Since, the washer was already open,... Read more

The problem seemed to be with the switch so I watched a few youtube videos to learn more about how ranges work. After locating the correct replacement switch I ordered it on-line around 10 pm Tuesday night. The new switch arrived Thursday morning at about 10 am and I had my range back up and working like new in less that 30 minutes. The hardest part was figuring out how to remove the slide in panel to access the switch. There were plastic washer/nuts behind each know which I was able to... Read more

• Won't start
• Element will not heat

Based on internet search and data found on APPLIANCE PARTS PRO, I deduced that the "infinite control " module was most likely bad. Replaced it and all is good. Toughest part was remembering how to disengage cooktop from down draft blower and then pulling the cook top up in within it's opening. Once pulled up, I put short 2x4's across the opening corners to support the cooktop safely while I worked on it. Next issue was figuring out exactly which screws held the glass top in place. As... Read more

Replaced the large burner control switches for the ones giving trouble. Since the other two switches had seen as much use as the faulty ones, replaced them too. After putting in new switches, found that one large burner had burned out so replaced it also. Range now cooks as good as new Read more

I used your chat and found out the year my stove was made. He also told me what part to order as one of the burners had stopped heating up. We watched the video on how to install it. My friend installed it and my stove burner now works. Read more

I took it apart to troubleshoot. I was pretty sure it was the switch but wanted to make sure it wasn't the element as well. Sure enough the switch was burnt at a little piece of copper protruding out the side. The plastic was blackened too which was a telling sign. The element was fine. I replaced the switch, turned on the cooktop and it worked again. Apparently, these switches are wired in series because when this one went out the rest of them wouldn't turn on either. Read more

Fix went fine, had to pull the dishwasher out to replace flood switch control board was very easy to replace, and fixed the problem. Read more

Replace dual infinity switch. The only difficulty is the terminal labels on the new switch did not match at all with the terminal labels on the original switch. The enclosed instructions were NOT helpful. But I contacted your representative, Johnny, and he was most helpful and patient. From my model number he located very specific and detailed instructions for how to wire the new switch. The rest of the job was easy. Your representative was outstanding. Thanks. Read more