Hardware Hand Small Engine Fuel Tank Parts

Our refrigerator takes care of my wife and I, along with our children when they visit, and the grand kids. Over the years, it's seen its fair share of wear and tear. Thankfully, nothing major has happened that hasn't been able to be repaired right here in the home, and by me. Our refrigerator is a GE side-by-side with an ice maker/water dispenser, and has held up well. I've ordered parts for it from AppliancePartsPros.com for all of its repairs, and while GE/Frigidaire have been changing out a... Read more

I had a slow leak at the water inlet valve where the water line from the filter assembly connected to the water inlet valve. I determine that the water line had scratches in it which caused it to not seal. Had to buy the entire reservoir and filter assembly to get that water line. The replacement was smooth. It took about 30 minutes to swap out and it fixed the leak. Read more

• Leaking

Replaced tank assembly. Actually I think the supply hose was originally not fully seated in the tank and I think I could have re-seated it deeper through the gray bushing. When I set the line into the new tank, still leaking. Pulled out supply line and reset using a little more force and line went into the tank. Took the bushing clip off the other tank and used it for the supply line bushing. So far, no leaks. The thing to remember is to push the edges of each hose bushing inward to pull... Read more

Water dispenser came down to a trickle and made a lot of noise, I changed the filter but it didnt help and thus the water tank/head assembly needed to be replaced. Replacing the water Tank/head assembly was an easy task, the hardest part is removing the covers and taking care of not breaking the insulation of the water inlet hose. For the not-so-experts like me it is also good to rememebr to have a bucket to collect all the water that comes out after the connection to the solenoid valves is... Read more

I was getting really frustrated with our oven. It would preheat to the correct temperature, then slowly lose heat until it was down to about 200 degrees. So it took about two hours to heat a pizza! Finally decided to repair the oven myself, rather than pay $300.00 to have a repair person come out. Ordered the replacement igniter from AppliancePartsPros.com, and it arrived in two days. I followed the instructional video on the AppliancePartsPros.com website, and it was going well until I... Read more

• Leaking

I replaced to offending part. The only minor issue was that the replacement part had changed design from the original. Otherwise it was a pretty straight forward operation. Read more

It took a little longer then I was hoping but wasn’t terrible. If the burner is very old at all make sure to get the new screws. Both of mine snapped when trying to remove them. The new one works great. Read more

After watching installation videos on each felt I could pull it off and ordered and received replacement water reservoir and water dispenser tube assembly. Reservoir installation went off without a hitch outside of the added step of the need to remove the entire main in waterline assy in order to access the connectors which also were not as represented in video, in that they were not the press-to-release type but standard threaded compression types. Water Dispenser tube/spout assembly was much... Read more

Ordered new Ignitor / Orifice and screws Mike was a great resource, he helped me thru the project. Read more

I replaced the supply line to the fridge - no change in taste. I replaced the MWF manifold and tubes, the water inlet valve and the water storage line. That did it, good tasting water again! The ice still has a bad taste, so I'll replace the supply tube from the valve to the ice maker. Overall, replacing these parts was easy and the videos from Appliance Parts Pros helped. Read more

Almost ordered solenoid valve but realize ice maker was working ok and water dispenser worked good for the first 1-2 seconds. Read online forums and found some posting about replacement of filter head w/ reservoir tha ressembled the problem I was having. Ordered filter head and got part within 2 day (even with ground shipping request). Took about an hour to carefully figure out how to remove covers and install part. An easy way to determine if solenoid is ok is removing filter and installing... Read more

Using the parts I ordered, I replaced the glass myself following the very helpful video on your web site. Read more

Secured the inner and outer door together and screwed handle back in place. Read more

I took the machine screws out of the outer panel for the right side only. Then pull the panel back a bit to release the lips from the front of the machine and had immediate access to the internal assembly that housed mounting nut. Order the new parts from AppliancePartsPro.com during the Thanksgiving week. Still received via FedEx in short time due to their same day shipping - which was greatly appreciated and surprising. Most small part places take a while to get the product out the door,... Read more

Replaced the hinge receiver with a new one. The old one was bent slightly inside where it could not be seen. I think someone pushed the door down to far or fell on it. 2 screws to remove it, take out storage drawer and reach up little ways to remove and replace the receiver. Replace the 2 screws. The receiver comes with 2 screws but I ordered an extra ( never used it ). The sides of the receiver were spread just a tiny bit but were enough to cause a problem. Read more

Had to remove all three food drawers and the back panel behind the drawers (4 screws). The water tank comes with the associated tubing which would typically require access to the back of the fridge to run the new lines. Instead I clipped the existing lines inside the fridge. Then I clipped the lines off the new tank so they would line up with the old lines. I then used a 5/16" OD compression coupling (Lowes or Home Depot) to connect the ends of the tubing together. The joined tubes are... Read more