Magic Chef Cogged Sump Filter Parts

• Will not drain

I've opened sump housing to check for clogging but it was clean. When I removed check valve to inspect it I've found out that the round part of the valve was missing so I figured it might've blocked the water exit at drain hose or something like that. So I pulled the dishwasher out to get a full access to drain hose connector and the pump. Upon disconnecting the drain and checking its connector I indeed found the round piece totally blocking the hose and acting as a seal. I removed the piece... Read more

• Not dispensing water
• Ice maker dispenses too little ice
• Ice maker won't dispense ice
• Ice maker not making ice

Ordered part and replaced it Read more

Remove upper and lower baskets for access. Remove 4 Torx screws holding drain/filter assembly, accessing last screw by rotating the water duct clockwise. Be sure to first un-clip the water duct at top and rear of dishwasher so that it can be moved. (Take the opportunity to remove accumulated deposits behind the water duct). Remove the drain/filter assembly and then remove the single screw holding the food chopper housing. Then remove the chopper assembly which is likely to be in pieces if it... Read more

• Will not drain

It was a relatively easy fix. Removed the small access panel at the back of the washing machine after unplugging the unit. The pump is right there. Disconnected the two hoses to the pump, catching some water with towels. Removed three retaining screws, then realized I had not disconnected the belt from under the unit. Easy fix, tilted the unit and disconnected the belt. Put in the new pump , connected the hoses, then reconnected the belts. Works like new! Read more

We were experiencing slow water flow from our Whirlpool interior water dispenser. The water would flow normally for a couple of seconds then subside to a trickle. After replacing the water filter and inlet valve, research suggested that the water filter head could be the culprit. In about 30 minutes, I was able to remove the old part and replace with a new part solving the problem. Read more

• Will not drain
• Burning smell
• Noisy

18 year old Maytag Atlantis top load washer had a load knocking and rattle sound with excessive vibration when the tub was spinning, but not when it was agitating. They was no water leaking. I took the front panel off and carefully listened while I ran a cycle and the loud sound sounded like it was coming from the drain pump. So I took off the drive belt and noticed that it was glazed and that there was belt material on the drain pump and tub transmission pulleys. I removed the drain pump and... Read more

My dishwasher quit cleaning dishes and lost all pressure. The food screen would keep clogging up and I would have to take it out and clean it by hand. After putting a new impeller in, the "gears" on the impeller connected with the screen blades, the old impeller the "gears" were stripped off. And the new impeller comes with new seals, after taking old one out I noticed it wasn't long before my old seals would have started leaking. Very simple repair if you watch the great video that... Read more

Replaced filter. It works great now, no more brown spots. Read more

• Touchpad does not respond

Ordered all the parts needed, replaced them and the Jenn Air worked just fine. Read more

• No heat or not enough heat

The root cause was the front glides. They were virtually gone, and the drum was on metal to metal. So I replaced them with a front glide kit. I also replaced the belt, rear rollers, and lint screen. I am happy to say all the parts fit perfectly, and I couldn't find a better price anywhere else. I will definitely keep you on file for the next time I need appliance parts! Thank you! Sincerely, pw Read more

I pulled the dryer away from the wall and unplugged it. Then I used a 5/16 nut driver and removed the 2 screws in the bottom front panel and pulled it off. Next I removed the 2 5/16 screws holding the front door panel and pulled it down far enough to disconnect the wires for the light and the wires on the door switch. Then , using a putty knife I popped the springs holding the top and control panel then pulling the top up and resting it against the wall. Now I started my repair by laying on... Read more

Water dispenser came down to a trickle and made a lot of noise, I changed the filter but it didnt help and thus the water tank/head assembly needed to be replaced. Replacing the water Tank/head assembly was an easy task, the hardest part is removing the covers and taking care of not breaking the insulation of the water inlet hose. For the not-so-experts like me it is also good to rememebr to have a bucket to collect all the water that comes out after the connection to the solenoid valves is... Read more

Dishes were 'gritty' with an almost invisible coating of specks smaller than grains of salt. Prior to ordering parts, I had to determine which part(s) needed replaced and which could benefit from a good cleaning. After viewing Appliance Parts Pros YouTube Videos, I removed the Main Manifold (snaps right off) including the Top Spray Arm. I discovered the Flappers of the Docking Station (AP6009888) were worn out and/or missing. I removed the Docking Station simply by popping the old one off... Read more

I reviewed the schematic and saw the Volute Seal, and Impeller Seal were the two that were closest my source of water. After watching the video about changing the Impeller/seal I removed the motor, impeller, and volute; I found that the impeller seal was the faulty one in my case. Since I'd ordered the volute and impeller seal kits (as I wasn't sure which it was) I installed both while I had it apart. Runs great, no water - simple to do. The seal changes took about 20 minutes. The only... Read more

• Not cleaning dishes properly

Searched on this site and found likely cause and solution to problem. After watching APP video, I was able to remove dishwasher filter and confirm clogged filter. Ordered the new part and it was shipped quickly. Reinstalled it per video instructions and it worked perfectly! Thank you APP.com for making me look like an appliance repair expert on this and several other projects. This has saved me lots of money over the last few years, and kept my slightly older appliances in working order and... Read more

Motor shaft was stripped, replaced with new shaft from Motor Seal Kit. Impeller was also cracked, so replaced it as well. I did run in to a small problem, the chopper blade was pressing against the metal grate on the piece that goes back over the motor seal. I spent about an hour messing with it, but thought maybe once it's all together it'll be fine. When you screw the impeller on, it pushes down the seals, which pushes down the chopper blade. Video on Motor Seal Kit page made it an... Read more