Shx2arl5uc/07 Parts

• overflowing

After first thinking I had a leak under my sink (dripping into my workshop in the basement), I quickly traced the source back to my Bosch dishwasher. I removed the bottom kick plate (phillips screwdriver) and could see a continuous drip from the Water Inlet Valve. Easy to see because the Water Inlet Valve is mounted in front. I shut off the power to the dishwasher at my breaker box and turned off the water to the dishwasher. First, I easily disconnected the power clip at the back of the Water... Read more

Removed Torx screws inside the dishwasher door, this causes the door panel to fall forward/down. Having a rug or something underneath to prevent scratches is useful. It's about 8 screws that need to come out, if I recall correctly they are all the ones with the torx head facing into the dishwasher when in the closed position. Then the panel comes off, exposing the bolts holding the handles, the cap comes off easily and replaces easily and reverse the process. Some of the screws are different... Read more

Ordered a new filter. Read more

• lights flashing or blinking
• Will not drain

Dishwasher died after 1 year and two weeks after purchase! The Bosch tech arrived and recommended replacing the drain pump (as well as cleaning the filter in vinegar). Ordered pump from APPros and it arrived THE NEXT DAY! Took out old one.... installed new one... and it worked! The new pump fit perfectly. Read more

The parts were to complete the install. Not a repair really. Although this was my first dishwasher install DIY. and thanks to the very fast and accurate parts delivery I was able to get everything done right the first time. Read more

• Will not dispense detergent

Process was a bit more complicated than the videos I had watched online. Had to remove both front panel and control panel to get to soap dispenser. Removed wires to soap dispenser and rinse aide dispenser. Removed wire "harness" around the top and right side of dispenser. Pried back the clips to allow dispenser to be pushed out. It was helpful to have another person to hold the door open at this point. Bent clips back and reinstalled everything. New part works great. Read more

Bought new wheel and the are easy to replace. Found why the brok and did a quick fix so it wont happen again. As the wheels age one will pull off then they all get weak and the rack will come off the track, To prevent this. you can put a plastic tie so the wheels cant fall off in the first place, The disign holds them in place with pressure from the plastic but the plastic ages and gets weak. A tie would have to actually break before the wheel can fall off. Read more

I only needed a flat head screwdriver to remove the clips holding the parts in. It took all of 10 minutes and the dish washer is running great now. Read more

The symptom was suds and water on the floor at the left front of the dishwasher within the first five minutes of operation. Examination of the seal inside the door showed it was warped and pushed up into the door out of place. Once disassembled we found a tear in the seal, severe warping, and the material was sticky and slimy rather than flexible. I found a video of the disassembly that was very helpful. It is necessary to pull the dishwasher out of the cabinet but my installation had no top... Read more

Because the door would no longer stay shut and didn't firmly click when closed. Reviewing reports on-line narrowed the problem, so I ordered the door lock assembly kit. Two Torx bits are needed: T10 for two screws that secure the gray latch/lock and sensor to the stainless interior wall of the door & T20 for twelve screws holding the control panel & decorative metal front to the interior wall. Pay close attention to theT20 screws, they aren't all one length. Remove the eight T20 screws holding... Read more

I only needed a flat head screwdriver to remove the clips holding the parts in. It took all of 10 minutes and the dish washer is running great now. Read more

I went on your very user friendly website and looked up my bosch dishwasher. I love your diagrams and I felt confident that I could figure out what we possibly needed to get the door to close correctly and get the washer back working again. Your staff is courteous, service was fast and I would definitely recommend Appliance Parts Pros. Read more

It finally gave E15 code, then after drying out the E15 code came back within 5 minutes of running. I dried out the base then I ran the dishwasher and observed water coming down the overflow chute after running only 5 minutes.There is a water inlet (clear water chamber on the side of the machine). It had some gunk inside that was stopping a black float shut-off from moving. I replaced the water inlet chamber. I also suspected the non return valve (also called a check valve). From the parts... Read more

This was a dishwasher swap out. I first turned the water off to the inlet hose of the dishwasher from underneath the sink. Removed the inlet water hose from sink to dishwasher. (use wrench or adjustable wrench) Then removed the screws securing old dishwasher from the cabinetry. I then pulled out the dishwasher from the cabinetry hole it was in. I unplugged the power cord from the wall of the old dishwasher. Then Ii removed the other end of inlet hose still attached to old DW (braided stainless... Read more

Replaced the sump drain hose. Read more