Turn Tip Small Engine On-Off Switch Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3406107
Dryer won't stop spinning when door opens or won't start at all? The door switch likely failed. DIY repair in 10-20 minutes with basic tools.
This part fixes the following symptoms
-
Doesn't shut off
-
Won't start
-
Will not tumble
See more...
Do-It-Yourself Stories from Customers like You
Ignitor coil was not turning on Harrison N. • El Cajon , CA • March 14, 2021
I realized my load of laundry was still wet after a normal drying cycle. My first action was to turn the dryer on (2010 gas Maytag centennial) and open the front port to look at the ignitor coil. It never turned orange so I knew there must be a problem with the primary circuit. I shut off the dryer, disconnected the power, pulled it away from the wall, shutoff the gas, and removed the back panel. I then disconnected the wires for the thermal fuse and checked its resistance with a multimeter....
Read more
More
$27.37
- Compare At:
-
$32.84
- You Save:
-
$5.47
Genuine Frigidaire part
By: Frigidaire
Part Number: 316436001
Burner won't turn off or stuck on high? This surface element switch controls heat settings for large burners. Moderate DIY with panel removal.
This part fixes the following symptoms
-
Won't start
-
Element will not heat
See more...
Do-It-Yourself Stories from Customers like You
The front left element (8 inch) would stay hot on lower control settings. Michael S. • West Seneca , NY • September 13, 2022
After an internet search, the likely problem was a faulty "Element Switch.." I actually unplugged the stove and removed the switch (I did NOT disconnect the wires). I obtained the part number on the switch, disassembled it, observed that the contacts were highly degraded, reassembled the switch and reinstalled it back into the stove. This all provided confidence the SWITCH was faulty.
One switch on the AppliancePartsPros.com website (AP2591804) looked exactly like the switch in the stove...
Read more
More
$51.30
- Compare At:
-
$61.05
- You Save:
-
$9.75
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3149400
Burner stuck on high or won't heat properly? This surface element switch controls your range burner temperature. Simple 15-minute DIY fix.
This part fixes the following symptoms
-
Won't start
-
Element will not heat
See more...
Do-It-Yourself Stories from Customers like You
The burner on my electric stove was "running wild" (not controlling temperature correctly) James S. • South Abington Township , PA • June 22, 2014
The fix was to replace the infinite control switch on my Whirlpool range. A simple task.
Read more
More
$56.34
- Compare At:
-
$67.04
- You Save:
-
$10.70
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10662129
The Run Capacitor is an OEM part for Whirlpool appliances, designed to provide the necessary electrical charge to start and run the compressor motor. This part attaches to the compressor to aids in maintaining a consistent motor speed and ensuring smooth operation. The run capacitor plays a crucial role in the appliance's electrical system, storing and releasing energy as needed to power the motor.
Causes of a bad Run Capacitor include electrical surges, wear and tear over time, or overheating, which can lead to a failure in providing the necessary start-up energy or maintaining motor speed.
Symptoms of a bad Run Capacitor include:
- The appliance does not start.
- The motor shuts off shortly after starting.
- The appliance is humming but not running.
- Increased energy consumption.
This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
This part fixes the following symptoms
-
Too warm
-
Clicking sound
-
Won't start
-
Freezer section too warm
See more...
Do-It-Yourself Stories from Customers like You
Both the freezer and refrigerator stopped cooling Raymond O. • Kerrville , TX • April 11, 2015
I have a Kitchen Aid side by side refrigerator/freezer which is 8 years old. One day it just stopped cooling. At first I was just going to junk it and purchase a new one. However, I took off the lower back cover and noticed the compressor was not running. I knew from experience that these compressors need a starter capacitor and relay and it is not uncommon for these parts to fail. I looked on the Internet for a video which showed how to remove the parts. I also found a video which showed how...
Read more
More
$45.30
- Compare At:
-
$54.36
- You Save:
-
$9.06
Genuine Ge part
By: Ge
Part Number: WD21X25468
Fix H2O error codes and water fill issues with this dishwasher pressure sensor. Monitors water level for proper fill cycles. DIY repair in about 1 hour.
Do-It-Yourself Stories from Customers like You
Mother board defective Gene J. • Fernandina Beach , FL • October 05, 2024
First diagnosed the problem by viewing several Youtube videos. Then ordered the part from AppliancePartsPros. After the part arrived I again referenced the best video - several times - and finally made the repair swapping out bad mother board with the new one from AppliancePartsPros. Saved me hundreds. Dishwasher works great, wife happy! All is good.
Read more
More
$29.57
- Compare At:
-
$35.48
- You Save:
-
$5.91
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8318084
Washer won't start, agitate, or spin? A faulty lid switch is the likely cause. This safety switch is easy to replace in under 5 minutes with basic tools.
This part fixes the following symptoms
-
Won't start
-
Timer will not advance
-
Will not drain
See more...
Do-It-Yourself Stories from Customers like You
Our washing machine filled then began washing the wife opened the lid to add one more item and it would no longer wash or spin Chris J. • Lakeland , FL • January 02, 2018
First I checked the circuit breakers and power to the outlet, then next wanted to check the lid switch, but it wasn't where I had found it on older models. I could hear it clicking on and off as I raised and lowered the lid, but it wasn't visible. I drained the tub through a siphon hose to lighten the machine, so I could slide it away from the wall to better see. Couldn't see the switch anywhere and decided it must be hiding in the raised console, but was unsure of how to attack it without...
Read more
More
$35.95
- Compare At:
-
$42.42
- You Save:
-
$6.47
Genuine Ge part
By: Ge
Part Number: WB24T10025
Burner stuck on high or won't heat? This 8-inch infinite switch controls heat output on electric ranges. Simple 20-30 minute DIY replacement.
Do-It-Yourself Stories from Customers like You
The heating element where boiling hot at any seting of the knob Christopher H. • Lawrence , KS • August 17, 2014
I replace the Infinite Switch and that seems to be the trick for keeping the temperture under control.
Read more
More
$43.50
- Compare At:
-
$52.20
- You Save:
-
$8.70
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10434452
The Dual Element Control Switch is an OEM part for Whirlpool ranges and cooktops. This control switch is designed for models with dual heating elements, allowing you to adjust the size of the heat output on the LF element depending on whether you are using the inner or outer element.
Causes of a bad Dual Element Control Switch can include electrical issues such as short circuits or worn contacts, physical damage to the knob or switch mechanism, or problems with the internal components that regulate power.
Symptoms of a failing Dual Element Control Switch include:
- Inability to change between the inner and outer elements
- Irregular heating or lack of response when adjusting the temperature
- The switch feeling loose or not engaging properly
- Burner not heating even though the switch is turned on
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Do-It-Yourself Stories from Customers like You
Large front burner stayed on high power. Lou G. • Mansfield , TX • October 12, 2019
Watched the attached video, then followed directions and installed the part ordered.
Read more
More
$78.95
- Compare At:
-
$93.95
- You Save:
-
$15.00
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3149404
Burner stuck on high or won't regulate temperature? This infinite switch controls top burner heat settings. Straightforward DIY fix, 15-30 minutes.
Do-It-Yourself Stories from Customers like You
Burners were working correctly most of the time but would stay in the on position (high )periodically and would not shut off automatically for the temperature you set the burner for Daryl B. • Gloucester , VA • August 12, 2021
Replaced the burner Infinite switches for the burners having the issue. Here are the latest part numbers for this model Maytag. Left rear (LR) and right rear (RR) burners are both 6" and use the same switch. Part # WP3149404. Left front (LF) is an 11 1/2" burner Part# W10167742. The right front (RF) burner is a double burner 6" center and 9 1/2" outside burner Part #WPW10149355. Very simple repair. Unplug the stove, remove the rear panel, remove the switch knob, remove the 2 switch screws,...
Read more
More
$52.68
- Compare At:
-
$63.22
- You Save:
-
$10.54
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10119326
Fix a mixer stuck on one speed or operating only at high speed. This speed control plate regulates mixer speed settings. Moderate DIY repair.
Do-It-Yourself Stories from Customers like You
My kitchenaid k5 ss had only one speed fast! Alice F. • El Dorado , KS • December 13, 2014
I read a few of your reviews and found that a, "Phase Control Board" may be the problem. It was! Talk about easy to install... It was super easy! I decided to order the, "Speed Control Plate" also as a precaution (Shipping was one price - and it arrived the very next day, Wow! I didn't expect that.) With my screwdriver and good lighting. I fixed it myself! My husband is still in shock. I used forceps to install the, "Speed Control Plate," because I needed something to hold the tension wire - at...
Read more
More
$20.95
- Compare At:
-
$24.72
- You Save:
-
$3.77
Genuine Ge part
By: Ge
Part Number: WB24T10029
Burner won't adjust temperature or stuck on high? This surface burner control switch restores heat control. Quick 10-minute fix with basic tools.
Do-It-Yourself Stories from Customers like You
Large dual burner Frederick E. • Athens , AL • September 19, 2014
Stove is a GE Adora Model JBP63HH2bb. It took me forever to figure out how the burner was attached to the rails.
My glass top was different than any instructions found on the internet for changing out a burner. The burners on this one are held to the bottom of the glass cook top by two rails that cross the bottom of the burner assemblies. In order to get too the burners you must remove 4 Phillips screws to lower the rails and burners from the cooktop. I suggest two people do this because...
Read more
More
$42.29
- Compare At:
-
$49.90
- You Save:
-
$7.61
Genuine Whirlpool part
By: Whirlpool
Part Number: W11396033
Interior lights staying on or not working? This door switch controls refrigerator lighting and functions. Moderate DIY repair with video guide available.
Do-It-Yourself Stories from Customers like You
Light switch on bottom freezer compartment flakey (intermittant) Alfred M. • Pahoa , HI • September 07, 2014
I watched the video on replacing the switch on a side freezer where prying out to original switch did not look difficult. I then got on the floor and tried to pry out my switch. Had a terrible time (locking tab or switch body hardened with time?) and mangled the switch terribly and the upper panel of the freezer somewhat, but the switch did come out. AND THEN the top freezer panel with the switch and light assembly fell out into my hands! I was able to unplug one Molex connector and the...
Read more
More
$30.54
- Compare At:
-
$36.65
- You Save:
-
$6.11
Genuine Ge part
By: Ge
Part Number: WE04X28977
Fix a dryer that won't start, keeps running with door open, or stops mid-cycle. This door switch replacement is a common DIY repair taking 15-30 minutes.
Do-It-Yourself Stories from Customers like You
The dryer door kept popping open. Debra S. • Peabody , MA • September 22, 2019
We ordered a door switch, dryer latch and strike plate. We realized that we only needed to replace the door switch. We watched a few videos and then replaced the switch. We couldn’t find a video for our model but they did give us a pretty good idea about what we needed to do. The hardest part was getting the original door switch out, all of the videos we watched showed us that it would pop out with a little pressure from a flat head screw driver, from the front of the switch. We could not get...
Read more
More
$14.95
- Compare At:
-
$17.94
- You Save:
-
$2.99
Genuine Lg part
By: Lg
Part Number: EBF62174907
Burner stuck on high or won't adjust temperature? This rotary switch behind the control knob regulates heat settings. DIY-friendly, 20-minute fix.
Do-It-Yourself Stories from Customers like You
The stovetop burner stopped working. Stephen E. • Apex , NC • September 19, 2021
Unscrewed the stove top, unplugged the connections, removed the stovetop. Replaced the burner and the switch. Put it back together again.
Read more
More
$93.95
- Compare At:
-
$111.80
- You Save:
-
$17.85
Genuine Frigidaire part
By: Frigidaire
Part Number: 316436000
Burner stuck on high or won't heat? This surface element switch controls temperature for electric range burners. DIY repair in under 30 minutes.
Do-It-Yourself Stories from Customers like You
Surface switches not operating properly; going from cool to very hot etc Guy G. • Guthrie , OK • October 10, 2014
Replaced all four element switches. Switches arrived within two days of ordering. That's about normal for AppliancePartsPros. They were the correct ones; not generic, and fit the original control knobs perfectly. This kind of service is what I'm used to from ApplicanePartsPros.
Read more
More
$60.52
- Compare At:
-
$72.02
- You Save:
-
$11.50
Genuine Frigidaire part
By: Frigidaire
Part Number: 131763256
Washer won't spin or drain? Error code E47? The door lock assembly often causes these issues. This moderately easy repair typically takes 30 minutes.
Do-It-Yourself Stories from Customers like You
My washer would not complete the spin cycle and wring the water out of the clothes Lisa C. • Spring Lake , NC • March 12, 2014
I ran a diagnostics check on the washing machine and came up with the error code E47 -Board thinks the door PTC circuit is open in spin. The washer thought the door was open and would not finish the spin. I was left with a washer full of very wet clothes. This repair was SO extremely easy. I only needed to uses a pair of needle nose pliers and a screw driver. It took less than 10 minutes, start to finish. Now the new door lock assembly registers correctly and my clothes are completely...
Read more
More
$83.56
- Compare At:
-
$99.44
- You Save:
-
$15.88