Electrolux Washer Gasket & Seal

The Door Boot Seal is an OEM part for Frigidaire washing machines. It forms a watertight seal between the washer's door and drum, preventing leaks during the wash and spin cycles. This flexible gasket ensures that water stays inside the drum, contributing to the washer's efficiency and reliability.

Common causes of a bad door boot seal include mold and mildew buildup, physical damage from sharp objects or overloading, and general wear and tear from regular use. A compromised seal can lead to water leaks and reduced washing performance.

Symptoms of a bad door boot seal include:

• Water leaking from the front of the washer
• Visible tears, cracks, or mold on the seal
• Unpleasant odors coming from the washer drum
• The washer door not closing or sealing properly

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Door Boot Seal is an OEM part for Frigidaire washing machines. It creates a watertight seal between the washer tub and the door, preventing water from leaking during the wash cycle.

Causes of a bad door boot seal can include wear and tear over time, mold or mildew buildup, and damage from sharp objects or improper cleaning methods. Exposure to harsh detergents or frequent overloading of the washer can also contribute to the deterioration of the seal.

Symptoms of a bad door boot seal include:

• Water leaking from the washer door
• Visible cracks, tears, or holes in the seal
• Mold or mildew buildup causing unpleasant odors
• Clothes coming out wetter than usual due to water leakage

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Drain Pump is an OEM component for Speed Queen washing machines. It is an important electric part that works to remove water from the washer tub at the end of each cycle. 

Symptoms of a failing drain pump include:

• The washer not fully draining water after cycles
• Excessively long drain times
• Unusual noises coming from the pump area

Causes stem from blockages in the pump chamber or drain hose, worn impeller assembly, or damaged electrical components inhibiting proper operation.

This Speed Queen replacement pump restores the machine's essential draining ability for hygienic washing. It ensures the removal of all water to prevent residual moisture issues. 

The Door Boot Seal is an OEM part for Frigidaire washing machines. It creates a watertight seal between the door and the drum of the washer, preventing leaks during operation.  

Causes of a bad door boot seal can include wear and tear over time, exposure to harsh detergents, or physical damage from sharp objects or heavy loads.  

Symptoms of a bad door boot seal include:

• Water leaking from the door area during wash cycles
• Visible tears, cracks, or mold buildup on the seal
• Unpleasant odors from the washer drum
• Difficulty in closing the washer door properly

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Door Boot Kit is an OEM part for Frigidaire washing machines. Also known as the door gasket or door seal, is located around the opening of the washing machine. It prevents water from leaking out during the wash cycle and maintains a secure seal when the door is closed.

Causes of a faulty door boot can include regular wear and tear, physical damage, or mold and mildew buildup. These factors can result in issues such as water leakage from the door, visible tears or cracks in the boot, or unpleasant odors from mold growth.

Symptoms of a bad door boot may include:

• Water leaking from the door during the wash cycle
• Visible tears, cracks, or deformations on the boot
• Foul odors emanating from the washing machine

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

This O-Ring creates a tight, leak-resistant seal between appliance components. Replacing a worn or flattened ring restores proper sealing, helps stop drips at the joint, and protects nearby parts from moisture and mineral residue.

• Provides a compression seal between fittings, housings, or tubes
• Helps prevent water leaks and loss of pressure at the connection
• Common signs of failure: moisture or residue around the joint, visible cracks/flattening, leaks after reassembly
• Regular wear, heat, chemicals, or age can harden or deform the ring

• Disconnect power and shut off the water supply before servicing
• Relieve line pressure and place a towel to catch residual water
• Clean mating surfaces; lightly lubricate the new O-ring with food-grade silicone grease
• Seat evenly without twisting or pinching; reassemble and check for leaks

This is a dispenser inlet gasket intended for use on washing machines. This part ensures that the hot and cold water lines do not leak at the point where they are connected to the appliance. If the washing machine is leaking, the gasket may need to be replaced.Replacing a dispenser inlet gasket in a washing machine can be done easily. Screwdrivers and pliers are required. Disconnect the appliance before starting the repair. Wear work gloves for safety. The hot and cold water lines should both be turned off and removed to prevent flooding.This dispenser inlet gasket is an authentic OEM replacement part. It is sourced from the manufacturer. The replacement component is made of high-quality materials. It can be installed in several different models of washing machines. The dispenser inlet gasket is compatible with appliances produced by Frigidaire, Gibson, Electrolux, Westinghouse, and Kelvinator brands.

This tub cover seal fits between the outer tub and the tub cover/splash guard on compatible washers. It keeps wash water and suds contained, helping prevent leaks from the top of the cabinet during agitation and spin.

• Forms a watertight barrier between the outer tub and the tub cover/splash guard
• Helps prevent splash-over and top-rim leaks during wash and spin
• Maintains proper containment of water and suds inside the tub assembly
• Common failure signs: water leaking from the top area, wet streaks down the outer tub, visible cracks, hardening, or flattening of the seal

• Disconnect power and shut off water supply before servicing; wear gloves and eye protection.
• Access the tub cover per service instructions; release the retainer ring/clips to remove the cover and old seal.
• Clean and dry all mating surfaces; remove residue so the new seal seats evenly.
• Lightly moisten the new seal, install uniformly around the rim, reinstall the cover/retainer, and run a short test with water to check for leaks.

This O-ring is a small rubber seal that helps prevent water or refrigerant leaks by creating a tight connection between mating parts. Replacing a worn O-ring restores a secure seal and reduces dripping or loss of pressure. What it does:

• Forms a leak-tight seal at a joint or fitting to stop drips and seepage
• Helps maintain proper fluid or refrigerant pressure where used
• Commonly replaced when cracked, flattened, or hardened
• Can eliminate intermittent leaks that occur under load or when the appliance cycles

• Turn off and unplug the appliance and shut off water or refrigerant supply before service
• Inspect mating surfaces and replace any damaged fittings to ensure a proper seal
• Lightly lubricate the O-ring with appliance-safe silicone grease; avoid petroleum-based products
• Do not stretch or nick the O-ring during installation; confirm correct seating before restoring power or supply

This drain hose ring secures the washer's drain hose to the tub or drain outlet to help maintain a watertight connection and prevent leaks. It's a direct-fit replacement for the original ring used on compatible Frigidaire washers. What it does:

• Secures and seals the connection between the drain hose and the washer tub or standpipe
• Helps prevent water leaks at the hose connection point
• Keeps the drain hose properly positioned to ensure reliable drainage
• Useful when replacing a cracked, stretched, or missing hose ring

• Disconnect power and shut off the water supply before starting repair
• Drain any standing water from the washer before removing the hose
• Use pliers or a suitable hose clamp tool to remove and install the ring; avoid pinching the hose
• After installation, run a short cycle and inspect the connection for leaks