Lat860aae Parts

• Spins slowly
• Burning smell
• Pumps but will not spin
• Noisy

The washer was on, and I heard a faint humming sound in the laundry room. I went in and opened the washer and it was full of soapy water in the middle of its cycle and was not agitating. I also smelled a faint burning smell. At this point I figured the problem was a bad motor, as the washer is more than 20 years old. I have fixed it twice before, because the first time, the repairman said I should keep this washer going as long as possible. It was made to last with a metal drum, unlike newer... Read more

• Will not drain
• Pumps but will not spin
• Timer will not advance
• Doesn't shut off

The lid shut-off switch is located behind the lid How About That. I order the plastic ball the hold the lid in place plus the lid shut off switch. I watched the video that AppliancePartsPros.com has on how to replace the lid and the plastic balls. I removed the lid to get to the two philips head screws to remove that part of the shut-off switch. I took the new switch out of the package and compared it to the old switch. I assembled the switch just like the old switch look using the new... Read more

I ordered the tub seal and stem seal kits along with the much needed spanner wrench. After viewing the video online several times and taking notes along the way I was ready to tackle the repair. After taking everything apart, I cleaned all areas thoroughly then addressed the rusty areas and mineral deposits found in the tub. Soaking the tub in vinegar and baking soda overnight helped loosen the built up deposits enough so I could carefully scrape them off with a spatula. This was very time... Read more

• No hot or cold water
• Will not fill with water
• Will not stop filling with water
• Noisy

1. Sleeve for input, Injector valve, nozzle and seal for input fixed this problem. Probably the main part that was the trouble was a deformed Injector Valve which is a rubber tube with an internal retention groove at the wide part that grips the Nozzle. The Sleeve and the Nozzle are hard plastic parts that basically looked fine, but I replaced them anyway while I was in there. Additionally I replaced the rubber Seal for Input which seals the plastic input fitting to the tub just to make sure... Read more

I ordered parts from appliance parts pro at 3:30 on Friday and they were delivered at bout noon on Saturday the next day. Took the machine apart removed the old pads. With the directions in the packages put it back together and the wife ran 5 loads of clothes through it. Works great. Was awesome to get the parts so quick Read more

I just wanted to put my experience here for all to see. I have a Maytag Neptune, MAH5500BWW, one of the original ones. I bought it back in 2002 and it has done many many loads of wash faithfully. So when the bearings started to get loud I thought it best to replace them, the seal kit and the belt. I did my research as best I could and decided to order the OEM parts from an appliance supplier. If you are replacing the bearings, watch on line videos prior to performing the job. It will... Read more

• No hot or cold water
• Will not fill with water
• Will not stop filling with water

Replaced the water valve. Easy repair. The repair video was spot-on. Tools needed: Slip joint pliers for removing and attaching the hoses and moving the hose clip. 5/16 nut driver. Phone to take a picture so I could get the wires put back right. Shut off the water and unplug from power. Remove the hoses. Using a 5/16 nut driver remove the single screw that holds the bracket, lift bracket slightly and pull from the washer. There is a little slack in wires and fill hose to work with. Take a... Read more

I took the cover off the transmission and determined that the only possible knocking had to be coming from the yoke. I ordered a new yoke and all the tub seals needed to put it back together like new. I also ordered a new drive pulley bearing because this bearing is always turning whenever the washer is used. I cleaned all the parts up while I was waiting for the new parts to arrive. I promised my wife I would make it look like new. I installed all the new parts in one day and let the... Read more

I ordered a new motor with a very helpful Chris.It arrived a day later with instructions and was easy to exchange with the old one.I am delighted with how it works and the price was good and the service excellent.thank you. Read more

1. Sleeve for input, Injector valve, nozzle and seal for input fixed this problem. Probably the main part that was the trouble was a deformed Injector Valve which is a rubber tube with an internal retention groove at the wide part that grips the Nozzle. The Sleeve and the Nozzle are hard plastic parts that basically looked fine, but I replaced them anyway while I was in there. Additionally I replaced the rubber Seal for Input which seals the plastic input fitting to the tub just to make sure... Read more

I noticed a lot of water on the floor one day. I had no idea where it came from (all pipes in the area near the stationary tub were dry, there was a small wet spot near the washer, but most of the water was more than 2ft from it). Started a small load and noticed water running down the outside of the unit. Immediately stopped the cycle and removed the front of the washer. Restarted the cycle and could see water spraying from the intake hose. Stopped the cycle and advanced it to spin to... Read more

• Will not stop filling with water
• Leaking

First off I have to say that Appliance Parts Pro's saved me from hiring a repair person, and quite possibly just getting rid of my washing machine. Their video's helped out SOOOOOOOO much and the advice one of their agents gave me over their online chat helped me trouble shoot something when I got stuck. On top of this they shipped my parts fast enough that less than 12 hrs later they arrived, which allowed me to get my machine up and running way faster than the other options I had available.... Read more

I replaced the hose between the tub and the pump. The clamp screws were quite rusted but I used a socket wrench on them since they have hex heads in addition to the screwdriver slot. If I had tried to use a screwdriver, I think it would have been difficult. I did not reuse the original clamps but replaced them with hardware store hose clamps. Read more

• Will not agitate
• Burning smell

The washer was on, and I heard a faint humming sound in the laundry room. I went in and opened the washer and it was full of soapy water in the middle of its cycle and was not agitating. I also smelled a faint burning smell. At this point I figured the problem was a bad motor, as the washer is more than 20 years old. I have fixed it twice before, because the first time, the repairman said I should keep this washer going as long as possible. It was made to last with a metal drum, unlike newer... Read more

• No hot or cold water
• Will not fill with water
• Will not stop filling with water

Ordered a new inlet water valve . Super fast delivery ordered on a Wednesday afternoon was here Thursday morning , standard shipping , I was impressed !! Removed the old valve , installed the new , checked for leaks no issues , washer is back on line and my Honey is very happy with me . Read more

We ordered parts from appliance parts pros and I fixed it. Read more