Parts for Frigidaire GS26HSZDW2: 13 - System Parts

Reduces chlorine taste and odor while filtering sediment from your refrigerator's water and ice. Replace every 6 months for best performance. Verify fit.

Water supply tube that routes water through your refrigerator to the ice maker and dispenser. Replace if cracked, leaking, or damaged during moving.

Dispenser not working or loose? This refrigerator dispenser frame secures ice and water dispenser components. Moderate DIY repair with video guide.

Torsion spring that returns the dispenser ice chute door to closed position. Replace if broken, weak, or missing to restore proper door closure.

This label module cover is a replacement outer cover that protects the control module label and front-top trim area while restoring a clean, finished appearance. It fits over the module opening and matches white appliance trim. What it does:

• Protects the control module label and underlying components from dirt and accidental contact
• Restores a clean, undamaged appearance when the original cover is cracked, faded, or missing
• Keeps important model/serial/label information visible and secure
• Helps prevent loose wires or small debris from contacting the module area

• One label module cover (white), as shown

• Disconnect power to the appliance before starting any work
• Typically installs by snapping into the control-module opening or fastening with screws—retain any original fasteners
• Handle carefully to avoid cracking the new plastic during alignment

Single mounting screw for securing refrigerator panels, brackets, and trim pieces. Replaces worn, stripped, or missing screws to restore proper fit.

Plastic drip tray installs under the refrigerator water/ice dispenser to catch spills and drips. Replace if cracked, warped, discolored, or missing.

This is a plastic actuator pad located behind the dispenser panel on a refrigerator door. When you press a glass against it, it triggers the water dispenser switch to start the flow of water. Replace this actuator if the water dispenser no longer responds to pressure, the paddle is cracked or broken, or if you have to press unusually hard to get water to dispense.

Insulating foam that installs on the ice chute door to prevent warm air and moisture around the dispenser. Replace if compressed, cracked, or missing.

Rubber ice dispenser door center seals the ice chute on your refrigerator. Replace if cracked, worn, missing, or not sealing properly to stop frost buildup.

Rubber seal for the ice dispenser door on side-by-side refrigerators. Replaces cracked, worn, or missing seals that allow warm air into the freezer.

This is the ice chute door assembly that covers the dispenser opening on the front of the refrigerator. It acts as a flap that opens when ice or water is dispensed and closes afterward to prevent warm air from entering the freezer compartment. Replace this part if the chute door is cracked, stuck, or no longer sealing properly - symptoms include frost buildup inside the dispenser area or ice melting and refreezing around the chute.

Replace your refrigerator's support plate or mounting bracket. Needed when the original is cracked, broken, or missing. Restores structural integrity.

Fix a refrigerator that beeps continuously, won't dispense ice or water, or shows unresponsive controls by replacing the control board. Moderate DIY repair.

The Ribbon Cable Harness is an OEM part for Frigidaire refrigerators. It connects various electronic components within the refrigerator, facilitating communication and control signals between them. This harness is essential for the proper functioning of the refrigerator's electronic systems.

Causes of a bad cable harness can include physical damage from bending or pinching, wear and tear from regular use, or electrical failures that disrupt signal transmission. Ensuring the integrity of this component is crucial for maintaining the appliance's performance.

Symptoms of a bad ribbon cable harness include:

• Intermittent or complete loss of electronic functions
• Error codes or malfunctioning display
• Unresponsive buttons or controls
• Inconsistent operation of refrigerator features

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Fix a dispenser that won't stop running water or ice, or won't dispense at all. This switch controls water and ice flow. Moderate DIY repair.

This door hinge pin forms the pivot for the refrigerator door hinge, keeping the door supported and aligned. Replacing a worn or missing pin restores smooth door movement and consistent sealing.

• Acts as the hinge's pivot shaft to support the door
• Helps maintain door alignment so the gasket can seal properly
• Reduces wobble and scraping at the hinge point
• Typical failure symptoms: door sagging, misalignment, poor closing, or a loose/wobbly hinge

• Unplug the refrigerator and remove items from the door to reduce weight.
• Support the door; remove hinge cover and screws, then lift the door off the hinge.
• Replace the hinge pin in the hinge bracket; transfer any existing spacers/bushings as designed.
• Reinstall and align the door; tighten hardware and verify smooth operation and seal contact.

Small spring that provides return tension for refrigerator actuator lever mechanisms. Replace if spring is broken, stretched, missing, or lost during repair.

Pan head

Bearing plate for refrigerators. Provides structural support for rotating components. Replace if cracked, warped, or damaged to restore stability.

Bearing plate for side-by-side refrigerators. Mounts and supports rotating components. Replace if cracked, worn, or broken to restore stability.

Inlet valve to door

Fix frozen water dispenser issues with this dispenser heater kit. Prevents ice buildup in the fill tube and restores water flow to your refrigerator.

Inlet valve to door

Fix frozen water dispenser issues with this dispenser heater kit. Prevents ice buildup in the fill tube and restores water flow to your refrigerator.

Replace your refrigerator's water inlet tube when cracked, split, or leaking. Connects water inlet valve to internal filter or dispenser system.

Replace your refrigerator's water inlet tube when cracked, split, or leaking. Connects water inlet valve to internal filter or dispenser system.

Seals internal refrigerator components to prevent air leaks and moisture intrusion. Replace when worn to maintain proper airflow and temperature control.

Seals internal refrigerator components to prevent air leaks and moisture intrusion. Replace when worn to maintain proper airflow and temperature control.

Water inlet tube connects the water valve to your ice maker. Replace if cracked, leaking, or damaged. Installs at the back of your refrigerator.

Water inlet tube connects the water valve to your ice maker. Replace if cracked, leaking, or damaged. Installs at the back of your refrigerator.