Parts for Kitchenaid KDTM404EBS0: 06 - Tub And Frame Parts

Dissolves limescale, mineral deposits, and odor-causing residues from dishwasher tub and spray system. Use monthly to maintain peak cleaning performance.

Protective cover that encloses your dishwasher's control box and internal wiring. Replace if cracked, broken, or missing to shield electronics from dust.

Prevents water leaks around your dishwasher door. Replace if you notice pooling water on the floor or visible cracks in the seal. Verify fit by model number.

The Screw Hole Cap is an OEM part for Whirlpool dishwashers. It covers the screw holes, providing a clean and finished appearance while preventing moisture and debris from entering the screw openings. This helps maintain the dishwasher's aesthetic and ensures that screws remain protected from rust and corrosion.

Causes of a bad screw hole cap can include regular wear and tear, accidental impacts, or misplacement during maintenance.

Symptoms of a bad screw hole cap include:

• Missing or loose caps
• Moisture or debris accumulating in screw holes
• Visible wear or damage to the caps

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Dishwasher won't start or door won't close? The door latch strike creates a secure catch point for proper door latching. Easy DIY repair.

Size: 1/4 inch hex head, 10-12 x 1/2 inch.

This is a sound-dampening insulation pad that attaches to the bottom of the dishwasher behind the toe panel. It helps reduce noise and vibration during wash and drain cycles. Replace this pad if it has become damaged, detached, or deteriorated, which can result in increased dishwasher noise.

If your dishwasher door drops, slams, or feels heavy, the door balance mount may be broken. This side-frame bracket anchors the spring system.

Screw secures appliance panels and access covers. Replace missing, stripped, or corroded screws to restore tight fit and eliminate rattles or gaps.

Secures your dishwasher to the underside of the counter. Replace if bracket is broken, cracked, or missing to prevent the unit from shifting forward.

10-24 threaded machine screw secures panels, brackets, and internal assemblies in appliances. Replace missing, stripped, or damaged screws.

10-32 threaded machine screw secures dishwasher panels, trim, and brackets. Replace when missing, stripped, or damaged to restore proper fit.

Rear support wheel for dishwasher lower rack assembly. Replaces broken, cracked, or missing wheels that cause dragging or misalignment on the track.

Pronged cup washer for securing internal dishwasher components. Provides reliable retaining force for assembly hardware.

Replacement door balance spring for dishwashers. Provides tension so the door opens smoothly and stays in position. Needed when spring is rusted, broken, or stretched causing door to slam open or fall without resistance.

Size: 8-32 x 1/2 inch.

Dissolves limescale, mineral deposits, and odor-causing residues from dishwasher tub and spray system. Use monthly to maintain peak cleaning performance.

Protects and conceals your dishwasher's electrical junction box. Replace if cracked, broken, or missing to keep wiring secure and restore a clean finish.

Door balance link kit for dishwashers. Connects door springs to control door movement. Replace if rope is frayed, broken, or plastic clips are cracked or worn.

Protective housing cap that encases the dishwasher thermostat. Replace if cracked, broken, or missing to properly shield temperature monitoring components.

Secures knobs, trim, or linkages to shafts inside your dishwasher. Replace if broken, cracked, or missing to prevent components from loosening.

This is an insulating sound shield that attaches to the outside of the dishwasher tub. It dampens noise and vibration during wash and drain cycles, helping to reduce overall operating sound levels. Replace this shield if it has become damaged, detached, or deteriorated, resulting in a noticeably louder dishwasher.

Secures the temperature sensor or thermostat to the dishwasher cabinet. Replace if the original bracket is cracked, broken, or missing hardware.

Fixes no heat during drying, wet dishes, or blinking sanitized light. This safety thermostat cuts power if water overheats. Moderate DIY repair.

Positions and supports the dishwasher tank assembly to maintain proper alignment. Replace if worn, cracked, or missing to restore correct spacing.

Spacer that mounts between dishwasher tank components to maintain proper alignment and reduce vibration. Replace if cracked, missing, or worn out.

Secures and aligns internal dishwasher components to prevent movement and noise. Replace if bracket is bent, cracked, or missing to restore stability.

Protective shield that guards internal dishwasher components from heat, moisture, and debris. Replace if cracked, broken, or missing to protect wiring.

Fix loose or rattling dishwasher parts with this 9/32" ratcheting retainer spring clip. Secures shafts and assemblies that vibrate free during cycles.

Insulation pad for dishwashers. Installs under the tub to reduce noise and improve heat retention. Replace if cracked, torn, or missing.

This factory screw secures panels, brackets, or components within your appliance. Using the correct OEM fastener helps ensure a snug fit and prevents loosening, rattling, or misalignment over time.

• Fastens metal or plastic components to maintain proper alignment
• Helps prevent vibration, noise, and loosened parts
• Common wear item that can strip, rust, or go missing
• Replaces damaged or missing hardware to restore secure mounting

• Disconnect power and shut off water or gas before service
• Note original screw location and orientation for proper reassembly
• Start threads by hand to avoid cross-threading; do not overtighten
• If threads are damaged, inspect the mating hole or clip before reuse

Dissolves limescale, mineral deposits, and odor-causing residues from dishwasher tub and spray system. Use monthly to maintain peak cleaning performance.