Wall Oven Gasket & Seal

This genuine replacement door seal restores a tight refrigerator fresh-food compartment closure to help maintain even temperatures and reduce frost, moisture, and energy loss. Use when the original gasket is cracked, warped, or no longer seals. What it does:

• Creates an airtight barrier between the door and cabinet to keep cool air in and warm air out
• Helps prevent condensation, frost buildup, and uneven cooling in the fresh-food compartment
• Reduces compressor run time and energy waste caused by a failing seal
• Stops door gaps that can allow food spoilage or excess moisture

• One replacement door seal/gasket for the fresh-food compartment

• Unplug the appliance or switch off power before starting any work
• Clean the mounting surface and remove old adhesive or debris for a proper fit
• Warm and flex the gasket if needed (per OEM guidance) to align and seat it evenly; avoid overstretching
• Inspect and reuse or replace retainers/clips as required; test seal by closing the door and checking for gaps

The Oven Door Gasket is an OEM replacement part for GE ranges and wall ovens. It provides a secure seal around the oven door to contain heat within the cooking cavity. The gasket is essential for efficient operation as it helps maintain optimal cooking temperatures.

Causes of a bad door gasket can include heat damage over time, warping from repeated door openings and closings, or accidental tears and ruptures. 

Symptoms of a bad oven door gasket include: 

• Excessive heat loss around the door area 
• Inconsistent or inefficient cooking performance
• The door not sealing properly, allowing heat to escape
• Rust or corrosion on interior door parts

This OEM GE part is compatible with GE, Hotpoint, Monogram, and certain Kenmore wall oven models.

This inner oven door glass seal cushions and seals the inner glass pane inside the door, helping contain heat and keep the glass stable and quiet. Replace a cracked or flattened seal to maintain safe, consistent oven performance.

• Seats and cushions the inner door glass panel
• Seals the perimeter of the pane to limit heat and air leaks
• Helps prevent debris and moisture between glass layers
• Can reduce rattling or shifting of the inner glass
• When worn, contribute to longer preheat times or temperature inconsistency

• Disconnect power; for gas ranges, also shut off the gas supply. Allow the oven to cool completely.
• Remove the door and separate the inner panel per your service instructions.
• Note the seal's routing and orientation; install the new seal without stretching or twisting.
• Wear cut-resistant gloves and handle glass carefully during reassembly.

This door gasket seals the broiler/bottom-oven door to help retain heat for more even broiling and reduce stray heat into the kitchen. It replaces worn or damaged seals that allow heat loss or uneven cooking. What it does:

• Creates a heat-tight seal around the broiler/bottom-oven door to improve cooking performance
• Helps prevent heat loss, uneven broiling, or extended cook times caused by gaps in the door seal
• Wear signs include visible cracks, flattened or torn material, and gaps around the door edge
• Replacing a damaged gasket can reduce smoke from burning food debris caught in a torn seal

• Disconnect power (and gas, if applicable) and allow the appliance to cool fully before starting
• Remove the broiler drawer or door per the owner's manual to access the gasket channel
• Clean the gasket channel of debris before seating the new gasket; press the gasket into the retainer evenly

A flexible replacement gasket that seals and side lamp glass, cushioning and securing the glass to help block moisture and debris from the lamp housing. Restores a tighter fit and reduces vibration or rattling around the lamp area. What it does:

• Seals the edge of the lamp glass to keep moisture, dust and food debris out of the lamp housing.
• Cushions and centers the lamp glass to reduce vibration and prevent rattling or glass movement.
• Helps maintain a stable lamp assembly so the light cover sits flush and stays in place.
• Use when the gasket is cracked, torn, deformed or missing, or when the lamp glass feels loose.

• Disconnect power to the appliance before servicing to avoid electrical shock.
• Handle lamp glass carefully to avoid breakage; wear gloves and eye protection as needed.
• Seat the gasket evenly around the lamp glass edge and press into the channel until fully seated; avoid stretching or deforming the seal.
• Replace only with the exact OEM part number to ensure correct fit and sealing.

This door gasket seals the refrigerator/freezer door to keep cold air in and maintain consistent temperatures. A correct replacement restores the door seal to help prevent leaks, frost buildup, and inefficient cooling. What it does:

• Replaces a damaged or worn door seal to restore a tight closure between door and cabinet.
• Helps stop cold air from escaping, reducing frost buildup and uneven temperatures.
• Minimizes energy loss caused by gaps or cracks in the existing gasket.
• Addresses symptoms such as visible cracks, gaps when door is closed, or increased running time.

• One white door gasket (as pictured).

• Unplug the appliance or shut off power before starting any repair.
• Inspect and clean the gasket channel and mating surfaces before installing the new seal.
• Start by seating the gasket into the corners, then press the gasket evenly into the channel around the door.
• Avoid using sharp tools that could tear the gasket; refer to the appliance manual for any model-specific steps.

This small rubber gasket seals and cushions an M4 fastener to help prevent leaks and reduce vibration at attachment points. It's a compact replacement part used where a watertight or vibration-damping seal is needed. What it does:

• Creates a seal around an M4 screw or bolt to help prevent water intrusion
• Cushions fasteners to reduce vibration, noise, and metal-on-metal wear
• Restores a tightened fastener's proper sealing surface when the original gasket is worn
• Helps maintain appliance integrity around panels, brackets, or connections

• Power off and unplug the appliance before starting any repair.
• Confirm the gasket's size matches the fastener and seating area before installation.
• Install flat against the mating surface; tighten fastener snugly but avoid over-torquing which can deform the gasket.
• Handle small parts carefully and retain any removed hardware for reassembly.

This burner seal fits around a cooktop burner to help keep spills and debris out of the burner housing and provide a stable, centered burner location for consistent heating. It restores a flush seal between the burner and the cooktop surface. What it does:

• Forms a protective gasket around the burner to block food, grease and liquids from entering the cooktop cavity
• Cushions and centers the burner, reducing wobble and promoting even element-to-surface contact
• Helps reduce smoke or odors caused by spills burning on exposed internal surfaces
• Restores proper fit after a cracked, torn or missing seal

• One burner seal

• Disconnect power to the appliance before servicing; if the range is gas, shut off the gas supply
• Remove the burner or lift the cooktop per your model's service instructions to access the seal area
• Clean and dry the mounting surface thoroughly before installing the new seal
• Press the seal into place; do not stretch excessively or use solvents/adhesives unless your model's instructions specify

This bulb-frame gasket seals the appliance door to prevent water and heat leaks and help the door close evenly. It restores a tight seal for better performance and reduces noise from a loose or damaged seal. What it does:

• Creates a watertight/airtight seal around the door frame to prevent leaks and heat loss
• Cushions the door edge so it closes smoothly and stays aligned
• Helps reduce vibration and rattling caused by a worn or compressed seal
• Common symptom: visible leaks at the door, steam or heat escaping, or a door that doesn't sit flush

• Disconnect power and water before starting any repair
• Remove the door or access panel for easier gasket replacement
• Work the gasket bead evenly into the door channel, ensuring the bulb is fully seated all the way around