Wall Oven Knob, Dial & Button

Color: White

Gas valve burner control knob. Color: Stainless. Measures about 2 inches in diameter.

This control knob replaces a worn or broken dial so you can select settings smoothly again. It restores a secure grip and clear pointer alignment, returning normal operation and a like-new look to your appliance. What it does:

• Attaches to the control shaft to operate the switch or thermostat
• Restores accurate selection when the original knob is cracked, stripped, loose, or missing
• Helps ensure the pointer/indicator lines up for clear settings
• Common symptoms: knob spins without turning the control, falls off, or is hard to grip

• 1 control knob

• Disconnect power to the appliance before servicing
• Pull the old knob straight off the shaft; avoid prying at an angle
• Align the new knob with the keyed/flat shaft and press straight on until fully seated
• If your model uses a spring insert/retainer inside the knob, ensure it's properly seated or transfer it from the old knob

Gas range and cooktop surface burner knob. Color: White. Measures about 2 inches in diameter. For black order WP3181304. For almond order WP3181306.

The Burner Knob is an OEM part for Whirlpool ranges and cooktops. This knob allows users to control the intensity of the stove's burner, offering a seamless interface for adjusting from a gentle simmer to a rolling boil. 

Over time, burner knobs can wear out or become damaged due to frequent use, exposure to heat, or accidental impacts. 

Symptoms of a bad Burner Knob include:

• Difficulty in adjusting the burner's flame or heat level
• The knob is loose or does not turn smoothly
• Visible cracks or damage to the knob
• The knob does not align properly with the burner settings

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This replacement control knob restores a secure, precise feel to your appliance's front panel controls so you can select settings and adjust heat smoothly and accurately. Ideal when the original knob is worn, cracked, or missing. What it does

• Attaches to the control shaft to operate the burner or function
• Restores clear pointer alignment and proper actuation
• Helps when the knob is loose, stripped, cracked, or falls off
• Improves control feel when settings are hard to select or the knob spins freely

• 1 control knob

• Disconnect power; shut off gas before servicing
• Pull the old knob straight off the stem—do not pry against the control panel
• Align the new knob with the stem and press it straight on until fully seated
• If it won't seat, inspect the stem for damage or misalignment before applying force

Color: Black

Color: Black. Measures about 2 inches in diameter. For white order WP74011276.

This replacement surface burner control knob restores a clean, precise feel to your range controls so you can set heat levels confidently. Ideal for replacing a cracked, stripped, or missing knob.

• Attaches to the burner valve or switch stem to select heat settings
• Common symptoms: knob wobbles, cracks, slips, or won't stay aligned with settings
• Restores accurate pointer alignment and consistent turning feel
• If the stem itself is damaged, the underlying valve/switch may also need service

• Turn the appliance off and allow all surfaces to cool
• Pull the old knob straight off the stem—do not pry against the panel
• Align the new knob with the stem and press straight on until fully seated at Off
• Rotate through all settings to confirm smooth operation

This replacement control knob restores smooth, accurate adjustment of your appliance's settings when the original is worn, cracked, or missing. Get a secure grip and the original look with a direct-fit knob that installs in seconds.

• Presses onto the control stem to actuate the underlying switch or valve
• Fixes knobs that are stripped, loose, wobbly, hard to turn, or missing
• Helps when the pointer no longer aligns with settings or the knob spins freely
• Direct-fit design maintains the original feel and operation

• Unplug the appliance or switch off power at the breaker before servicing
• Pull the old knob straight off; avoid bending the control shaft
• Align the new knob's insert with the flat/key on the stem and push fully into place
• Verify smooth rotation and proper engagement of the control

Restore smooth, accurate control of your appliance with this Control Knob Kit. It replaces worn, cracked, or missing knobs so you can reliably select settings and refresh the appearance of the control panel. What it does:

• Transfers your hand turn to the control valve/switch to adjust heat or settings
• Helps resolve stripped, cracked, or spinning knobs that won't engage properly
• Replaces missing or loose knobs for consistent, confident operation
• Refreshes front-panel look when old knobs are faded or damaged

• 1 control knob kit

• Disconnect power and allow the appliance to cool before servicing
• Pull the old knob straight off the stem; do not pry against or twist the valve stem
• Align the knob opening with the stem and press on firmly until fully seated
• Do not force installation to avoid damaging the control stem

The Whirlpool Range Knob is an OEM replacement part designed for Whirlpool ranges. This stainless steel knob allows you to control the different functions and settings of your range, such as adjusting the temperature or selecting the cooking mode.

Over time, the knob may become worn, cracked, or damaged, making it difficult to accurately set or adjust the desired settings on your range. A faulty knob can hinder your ability to control the range effectively and may impact your cooking experience.

Symptoms of a faulty Range Knob may include:

• Knob becoming loose or spinning freely
• Difficulty in turning or adjusting the knob
• Knob cracked or broken, preventing proper usage
• Inaccurate alignment or marking on the knob

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore ovens and ranges.

The Knob is an OEM part for GE ranges and cooktops, designed to allow users to control the heat output of the stove's burners. This knob is a direct replacement for the original equipment, ensuring a perfect fit and proper function. It is typically made of durable materials to withstand the heat and frequent use associated with cooking.  

Over time, burner knobs can become worn or damaged due to heat exposure, cleaning chemicals, or accidental impacts. This wear can lead to difficulty in accurately setting the burner temperature or, in some cases, the knob may become loose or break off entirely.

Symptoms of a bad Burner Knob include:

• Difficulty in turning the knob or a lack of resistance 
• Faded or missing indicator markings 
• The knob no longer aligns correctly with the burner's settings 

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 

This control knob lets you select settings on your appliance. Replacing a worn or missing knob restores smooth, reliable control and a finished look to the front panel. What it does:

• Attaches to the control shaft to adjust appliance settings
• Restores positive engagement when the original knob is cracked or stripped
• Helps ensure accurate, repeatable adjustments
• Common symptoms: knob broken, loose, missing, or spins without turning the control

• Includes 1 control knob

• Disconnect power and shut off gas before servicing
• Pull the old knob straight off the shaft; avoid prying on the control panel
• Align the new knob's hub with the shaft and press firmly until fully seated
• Verify smooth rotation and proper engagement before returning the appliance to service

This replacement control knob restores smooth, reliable selection of your appliance's settings. Installing this part helps you accurately choose cycles, temperatures, or burner levels again.

• Attaches to the control shaft to operate a switch, valve, or timer
• Provides clear position indexing for accurate setting selection
• Typical symptoms: loose or wobbly knob, slips, won't turn the control, or falls off
• Replacing a damaged knob can resolve difficulty selecting cycles, temperatures, or burner output

• Disconnect power before servicing; if working on a gas range, also shut off the gas supply as needed
• Pull the old knob straight off the shaft—do not pry against the control panel
• Align the new knob with the shaft orientation and press straight on until fully seated
• Verify operation by rotating through all positions

Color: Black. Measures about 2 inches in diameter. For biscuit use WP98008208. For white use WP98006102. Sold individually.