White Westinghouse Washer Dryer Combo Gasket & Seal

The Lower Felt Seal is an OEM part for Frigidaire dryers. This part creates a tight seal between the drum and the front panel, preventing air leakage and reducing energy consumption.

Symptoms of a failing Lower Felt Seal include:

• Clothes getting snagged or caught during the drying cycle
• Increased drying times due to heat escaping from the drum
• Excessive noise or squeaking as the drum rotates
• Visible wear, tears, or gaps in the felt seal

Causes of a bad lower felt seal can include regular wear and tear from the constant rotation of the drum, physical damage from overloading the dryer, or deterioration due to exposure to heat and humidity over time.

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

The Drum Glide is an OEM part for Frigidaire dryers. It is designed to support the front of the dryer drum as it rotates, allowing the drum to turn smoothly with minimal friction and noise. This is a single glide. Your dryer uses two so it is recommended to replace both at the same time.

Causes of a bad drum glide can include wear and tear from regular use, excessive loads that put undue strain on the drum and its components, or accumulation of lint and debris that can interfere with the glide's movement.

Symptoms of a bad Drum Glide can include:

• Unusual noises, such as screeching or squealing, during operation
• Increased difficulty in turning the drum, leading to longer drying times or incomplete cycles
• Visible wear or damage to the glide itself, indicating it is time for a replacement

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

The Upper Felt Seal is an OEM part for Frigidaire dryers. It provides a seal between the dryer drum and the front panel, helping to retain heat and ensure efficient drying performance. This felt seal also minimizes friction between the drum and the front panel, reducing wear on the drum and the appliance itself. The seal measures approximately 16.5" long x 1" wide. The adhesive is included as well.

Causes of a bad upper felt seal can include wear and tear over time, exposure to high heat, or damage from foreign objects caught in the drum. A compromised felt seal can lead to inefficient drying and increased energy consumption.

Symptoms of a bad upper felt seal include:

• Clothes taking longer to dry
• Excessive lint accumulation inside the dryer
• Unusual noises during the drying cycle
• Visible damage or gaps in the felt seal

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Also available in maintenance kit: Part Number 5304457724.

The Dryer Seal is an OEM replacment part for Frigidaire dryers. It is located at the doorway opening where the drum rotates and helps prevent lint, moisture, and heat from escaping. The seal is a crucial component that ensures efficient drying and heat retention within the dryer drum. 

Causes of a bad seal can include wear and tear over time from continuous use or damage due to mishandling. The nylon seal experiences a lot of friction and heat stress with each drying cycle.

Symptoms of a bad seal include: 

• Increased drying time as heat escapes 
• Excess lint and moisture accumulation inside dryer components
• Visibly worn or cracked seal edges
• Cool air leakage noticed around the door when the dryer is running

This OEM Frigidaire replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. 

The Door Boot Kit is an OEM part for Frigidaire washing machines. Also known as the door gasket or door seal, is located around the opening of the washing machine. It prevents water from leaking out during the wash cycle and maintains a secure seal when the door is closed.

Causes of a faulty door boot can include regular wear and tear, physical damage, or mold and mildew buildup. These factors can result in issues such as water leakage from the door, visible tears or cracks in the boot, or unpleasant odors from mold growth.

Symptoms of a bad door boot may include:

• Water leaking from the door during the wash cycle
• Visible tears, cracks, or deformations on the boot
• Foul odors emanating from the washing machine

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

The Gasket is an OEM part for Frigidaire washing machines. This part is located between the front and rear outer tubs and prevents water leaks by maintaining a watertight seal between them. The gasket acts as a barrier to ensure that water used during the washing process remains contained within the inner tub, preventing it from seeping into the washing machine's surrounding components.  

Causes of a bad gasket can include regular wear and tear, exposure to harsh detergents, or deterioration over time.  

Symptoms of a bad gasket include:

• Water leaking from the outer tub area
• Visible cracks or deterioration in the gasket material
• The washing machine not holding water properly
• Increased noise or vibration during operation

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This tub cover seal fits between the outer tub and the tub cover/splash guard on compatible washers. It keeps wash water and suds contained, helping prevent leaks from the top of the cabinet during agitation and spin.

• Forms a watertight barrier between the outer tub and the tub cover/splash guard
• Helps prevent splash-over and top-rim leaks during wash and spin
• Maintains proper containment of water and suds inside the tub assembly
• Common failure signs: water leaking from the top area, wet streaks down the outer tub, visible cracks, hardening, or flattening of the seal

• Disconnect power and shut off water supply before servicing; wear gloves and eye protection.
• Access the tub cover per service instructions; release the retainer ring/clips to remove the cover and old seal.
• Clean and dry all mating surfaces; remove residue so the new seal seats evenly.
• Lightly moisten the new seal, install uniformly around the rim, reinstall the cover/retainer, and run a short test with water to check for leaks.

This drain hose ring secures the washer's drain hose to the tub or drain outlet to help maintain a watertight connection and prevent leaks. It's a direct-fit replacement for the original ring used on compatible Frigidaire washers. What it does:

• Secures and seals the connection between the drain hose and the washer tub or standpipe
• Helps prevent water leaks at the hose connection point
• Keeps the drain hose properly positioned to ensure reliable drainage
• Useful when replacing a cracked, stretched, or missing hose ring

• Disconnect power and shut off the water supply before starting repair
• Drain any standing water from the washer before removing the hose
• Use pliers or a suitable hose clamp tool to remove and install the ring; avoid pinching the hose
• After installation, run a short cycle and inspect the connection for leaks

This air duct seal creates a tight barrier between the dryer's lint housing and cabinet. Replacing a worn seal helps prevent air leaks, maintain proper airflow through the lint filter, and restore consistent drying performance.

• Seals the air duct/lint housing to the front panel to direct airflow through the lint screen and drum
• Helps maintain dryer efficiency and temperature control by preventing bypass air leaks
• Common symptoms of a failed seal include longer dry times, weak exhaust airflow, excess lint inside the cabinet, or lint around the door opening
• Replaces a deteriorated or missing seal to restore the intended air path

• Disconnect power; shut off gas supply for gas models
• Access the air duct by removing the lint screen and top/front panels as needed
• Remove the old seal and any residue; clean mating surfaces before installing the new seal
• Seat the duct evenly against the panel when reassembling to ensure a uniform seal

The blower housing seal is a perimeter gasket that closes the gap between the blower housing and the adjoining duct or bulkhead. It keeps airflow contained for efficient operation and helps prevent air leaks and debris from escaping.

• Seals the blower housing joint to minimize air leakage
• Helps maintain proper airflow for consistent performance
• Reduces dust/debris escape into the cabinet or surrounding area
• Replaces torn, brittle, flattened, or missing seals that can cause weak air output or rattling

• Disconnect power; turn off gas supply before servicing.
• Access the blower housing; note the original routing/orientation of the seal.
• Remove the old seal and clean mating surfaces of lint and residue.
• Seat the new seal evenly with no gaps or twists; reassemble and verify airflow.

The Front Felt Glide Assembly is an OEM part for Frigidaire dryers. This part allows smooth operation of the dryer drum, providing a felt pad that the drum glides on as it rotates. This not only helps to support the drum but also minimizes friction and noise, contributing to the efficient and quiet operation of the dryer. 

Over time, the felt portion of the glide assembly can wear down, leading to increased friction between the drum and the dryer's front panel.  

Symptoms of a bad Front Felt Glide Assembly include:

• Unusual noises during operation, such as squeaking or grinding
• The dryer drum may catch or hesitate during rotation
• Increased wear and tear on clothing due to the drum's rough movement
• The dryer may take longer to dry clothes efficiently due to the drum's impaired rotation

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.