White Westinghouse Dryer drum not turning: Common Causes & How to Fix

Repair Instructions:

The White Westinghouse dryer has a long, thin belt that goes around the drum and two pulleys. One pulley is for tension and the other is on the motor. With regular use, this belt can break over time. If the belt breaks, the drum won't turn. To check if the belt is broken, reach into the White Westinghouse dryer and try to turn the drum by hand. If the drum spins very easily, the belt is probably broken. Look at the belt to confirm it is broken. If the belt is broken, you need to replace it. Replacing the belt will allow the drum to turn again.

How to Replace White Westinghouse Dryer Drive Belt

1. Unplug the White Westinghouse dryer from the power source. Make sure the White Westinghouse dryer is completely powered off.

2. Open the White Westinghouse dryer cabinet to access the belt and rollers. The top or front panel usually comes off easily.
3. Locate the drive belt and examine it for signs of wear and cracking. Identify the path it takes around the rollers.
4. Turn the rollers to loosen tension, then lift the belt up and off the pulleys. Be careful not to tear the old belt.
5. Compare the old belt to the new one to ensure you have the correct length and type.
6. Place the new belt onto the pulleys, following the same path as the old one. Make sure it isn't twisted.
7. Turn the pulleys and check that the belt is centered and tight. Adjust tension as needed.
8. Re-install the White Westinghouse dryer cabinet panels and secure them in place with screws.
9. Plug in the White Westinghouse dryer and run it empty to verify the drive belt is working properly before drying clothes.
10. Make sure the White Westinghouse dryer is not excessively noisy with the new belt installed.

Repair Instructions:

If your White Westinghouse dryer drum is not turning, it's probably not because of a bad timer. That rarely happens. First check the parts that usually break. If everything else is working right, then test the timer. Use a multimeter and wiring diagram to check the timer. If the timer is bad, replace it. But again, the timer is not likely to be the problem if the drum won't turn. Look at the other parts first before replacing the timer.

How to Replace White Westinghouse Dryer Timer

1. Unplug the White Westinghouse dryer from the power source. Make sure the White Westinghouse dryer is completely powered off.

2. Open the White Westinghouse dryer control panel to access the timer. It is usually located behind a panel on the top console.
3. Take a photo of the wire connections on the old timer for reference. Then remove the wires noting their positions.
4. Remove the mounting screws that secure the timer using a Phillips head screwdriver.
5. Carefully remove the old timer and dispose of it properly.
6. Position the new timer in place and reinstall the mounting screws to secure it.
7. Reconnect all the wires to the same terminals they were originally attached based on your photo. Double check connections.
8. Reinstall the White Westinghouse dryer control panel ensuring all components are secure.
9. Plug in the White Westinghouse dryer and test both heating and cycles to verify the new timer is working properly before drying clothes.
10. Refer to a wiring diagram if needed to troubleshoot any connections.

Repair Instructions:

Most White Westinghouse dryers have two rollers in the back of the drum. Some also have two rollers in the front. The rollers need to spin easily to work right. If the rollers are worn out, the drum can't turn properly. To check the rollers, take off the belt and try turning the drum by hand. If the drum doesn't spin freely, the rollers may be worn out. Look at the rollers to see if any are worn. If one or more are worn, replace all the rollers at the same time to prevent future issues. You can reuse the roller shaft if it's in good shape. Make sure to clean the shaft before putting on the new rollers.

How to Replace White Westinghouse Dryer Drum Roller

1. Unplug the White Westinghouse dryer from the power source. Make sure the White Westinghouse dryer is completely powered off before attempting this repair.

2. Open the White Westinghouse dryer door and remove the lint screen and filter cover (if applicable) to access the drum.
3. Locate the roller you need to replace on the back side of the drum. It will be mounted on a wheel and axle.
4. On each side, remove the retaining clip that secures the roller to the axle using pliers.
5. Wiggle the roller wheel side to side to loosen it and slide it off the axle. You may need to move the drum.
6. Vacuum around the axle to remove any dust, lint or debris. Make sure the axle is clean.
7. Slide the new replacement roller wheel onto the axle, aligning the clip grooves.
8. Reattach the retaining clips on both sides to secure the new roller in place. Make sure they click into place.
9. Check that the drum rotates freely by turning it manually. The roller should spin smoothly.
10. Reattach the lint filter and close the White Westinghouse dryer door. Plug in the White Westinghouse dryer and test it empty before drying laundry.

Repair Instructions:

The blower wheel in the White Westinghouse dryer moves air through the drum. The motor that turns the blower wheel also runs the belt for the drum. So if the blower wheel gets blocked, it could stop the drum from turning too. Check the blower wheel and housing for anything blocking it. If you see an obstruction, replace the blower wheel or housing. Replacing the part will help get the drum turning again.

How to Replace White Westinghouse Dryer Blower Wheel

1. Unplug the White Westinghouse dryer from the power source. Make sure the White Westinghouse dryer is completely powered off.

2. Open the blower housing usually located in the back panel or side of the White Westinghouse dryer.
3. Remove the retaining screw in the center of the blower wheel using a Phillips head screwdriver. This releases the wheel from the motor shaft.
4. Carefully slide the old blower wheel off the shaft. Be mindful of the fins, they may be sharp.
5. Compare old and new blower wheels to ensure correct replacement. Make note of the direction and angle of the fins.
6. Before installing, vacuum the blower housing to remove built up lint and debris.
7. Slide the new blower wheel onto the motor shaft at the same angle as the old one. Make sure it is fully seated.
8. Reinstall and tighten the retaining screw through the center of the blower wheel.
9. Reattach the blower housing cover using the retaining screws.
10. Plug in the White Westinghouse dryer and run a test cycle to verify proper airflow before drying clothes.

Repair Instructions:

A White Westinghouse dryer's control board controls the voltage being sent to all of the appliance's electrical components. If the board is defective, it may interrupt voltage to the drive motor resulting in the drum not turning. You can inspect the board for signs of damage or a shorted component. You can also use a multimeter to test for voltage reaching the drive motor after reviewing the White Westinghouse dryer's wiring diagram.

How to Replace White Westinghouse Dryer Control Board

1. Unplug the White Westinghouse dryer from the power source. Make sure the White Westinghouse dryer is completely powered off.

2. Open the control panel on the White Westinghouse dryer, usually on the top front area. Remove any screws securing it.
3. Take photos of all wire connections on the old control board to use for reference later.
4. Disconnect the wires from the terminals noting their positions. Remove any mounting screws.
5. Carefully remove the old control board and dispose of it properly.
6. Position the new control board and reinstall any mounting screws to secure it.
7. Refer to your photos to reconnect each wire to the correct terminal. Double check connections.
8. Reinstall the control panel cover and secure with screws.
9. Plug in the White Westinghouse dryer and turn it on to verify functionality. Test all settings before drying clothes.
10. Refer to a wiring diagram if needed to troubleshoot any connections on the new control board.

Repair Instructions:

Most White Westinghouse dryers have two rollers in the back of the drum. Some also have two rollers in the front. The rollers need to spin easily to work right. If the rollers or axles are worn out, the drum can't turn properly. To check them, take off the belt and try turning the drum by hand. If the drum doesn't spin freely, the rollers or axles may be worn out. Look at the rollers and axles to see if any are worn. If one or more are worn, replace all the rollers at the same time to prevent future issues. You can reuse the axles if they're in good shape. Make sure to clean the axles before putting on the new rollers.

How to Replace White Westinghouse Dryer Drum Support Roller & Axle

1. Unplug the White Westinghouse dryer from the power source. Make sure the White Westinghouse dryer is completely powered off.

2. Open the White Westinghouse dryer door and remove the lint screen to access the drum.
3. Locate the support roller you need to replace under the rear of the drum.
4. Remove the retaining clip from the roller's axle using pliers.
5. Slide the roller off the worn axle. You may need to wiggle it side to side.
6. Vacuum around the axle to remove any dust, lint or debris.
7. Slide the new support roller onto the new axle, aligning the clip grooves.
8. Reattach the retaining clip to secure the support roller in place. Make sure it clicks into place.
9. Check that the drum rotates freely by turning it manually.
10. Reattach the lint screen and close the White Westinghouse dryer door. Plug in the White Westinghouse dryer and test it empty before drying laundry.

Repair Instructions:

The drive motor turns the drum and blower wheel to push out the air. First, see if the motor makes a humming noise. If it still hums, take off the belt from the motor. Then check that nothing is blocking the blower wheel. Next, with the belt off, try to turn the drum by hand. If the drum doesn't spin easily, find out what's stopping it from turning. If the drum spins freely and nothing blocks the blower, the drive motor may be bad. If you think the motor is the problem, replace it. That should fix your White Westinghouse dryer.

Repair Instructions:

A White Westinghouse dryer repair kit usually has a new belt, idler pulley, and may also contain rollers, a rear drum bearing, a felt seal, and other parts. A broken belt, bad idler pulley, and worn out rollers or bearings are the main reasons a White Westinghouse dryer drum won't turn. So putting in a new maintenance kit should fix the problem of the drum not spinning. The kit replaces the parts that typically cause the drum to get stuck.

How to Replace White Westinghouse Dryer Maintenance Kit

1. Unplug the White Westinghouse dryer from the power source. Make sure the White Westinghouse dryer is completely powered off.

2. Open the White Westinghouse dryer cabinet to access the belt, rollers, and other moving parts. The top panel usually removes easily.
3. Inspect each part you will be replacing - make note of their positions and how they are assembled.
4. Use a screwdriver to remove the old idler pulley and replace it with the new one in the kit.
5. Remove the worn belt and replace it with the new belt, following the same path around the rollers.
6. Check that the new belt is centered on the pulleys and has proper tension.
7. Replace the rollers or axles if included in the kit, transferring any clips or retainers.
8. Vacuum out any built up lint or debris from inside the White Westinghouse dryer once done.
9. Reinstall the White Westinghouse dryer cabinet panel and secure with the retaining screws.
10. Plug in the White Westinghouse dryer and run a test cycle before drying clothes to verify all new parts are working properly.

Repair Instructions:

The main control board in a White Westinghouse dryer controls the power going to all the parts. If the board is bad, it could stop sending power to the motor. This would make the drum not turn. Look at the board for any damaged or shorted parts. You can also use a multimeter to check if power is getting to the motor. First check the wiring diagram for the White Westinghouse dryer. Replacing the control board can fix the problem if it's not giving power to the motor.

How to Replace White Westinghouse Dryer Main Control Board

1. Unplug the White Westinghouse dryer from the power source. Make sure the White Westinghouse dryer is completely powered off.

2. Open the control panel on the White Westinghouse dryer, usually on the top front area. Remove any screws securing it.
3. Take photos of all wire connections on the old control board to use for reference later.
4. Disconnect the wires from the terminals noting their positions. Remove any mounting screws.
5. Carefully remove the old control board and dispose of it properly.
6. Position the new main control board and reinstall any mounting screws to secure it.
7. Refer to your photos to reconnect each wire to the correct terminal. Double check connections.
8. Reinstall the control panel cover and secure with screws.
9. Plug in the White Westinghouse dryer and turn it on to verify functionality. Test all settings before drying clothes.
10. Refer to a wiring diagram if needed to troubleshoot any connections on the new main control board.

Repair Instructions:

Look at the idler pulley for the White Westinghouse dryer drum belt. Make sure it can spin easily on the shaft. If the idler pulley is stuck, worn out, or damaged, you should replace it. When you replace the idler pulley, also put in a new belt for the drum drive. Replacing both together will help make sure your White Westinghouse dryer runs properly.

How to Replace White Westinghouse Dryer Idler Pulley

1. Unplug the White Westinghouse dryer from the power source. Make sure the White Westinghouse dryer is completely powered off.

2. Open the White Westinghouse dryer cabinet to access the belt and pulleys. The top or front panel usually comes off easily.
3. Locate the idler pulley and examine it for damage or signs of wear. Note how it guides the drive belt.
4. Remove the idler pulley retaining clip using pliers.
5. Slide the idler pulley off the mounting bracket. You may need to move the pulley arm.
6. Place the new idler pulley on the mounting bracket in the same position as the old one.
7. Reattach the retaining clip to secure the idler pulley in place. Make sure it clicks into position.
8. Check the belt path and adjust tension if needed by moving the idler pulley arm.
9. Re-install the White Westinghouse dryer cabinet panels and secure them in place with screws.
10. Plug in the White Westinghouse dryer and run it empty to verify the idler pulley is working properly before drying clothes.