White Westinghouse Washer Dryer Combo Parts

• Will not tumble

I found a video on Youtube which described dryer drum squeaks as most likely caused by a worn rear drum bearing. I located the model number on the inside lip of the dryer door: Frigidaire Affinity LEQ6000ES2. I googled "frigidaire affinity dryer squeak". I got a link for my friends at AppliancePartsPros.com! I've used Appliance PartsPros 3 times before, so I figured I was in a "one-stop-solution" situation. I ordered a rear drum bearing kit as well as a dryer drum belt (after nearly 7 years... Read more

• Shuts off too soon
• Too hot
• Takes too long to dry
• No heat or not enough heat

My appliance repair guy checked out the problem, but the stack washer dryer required the contractor to dismantle the cabinet to allow the repair to occur. So i wanted the parts available for the repair, so we would not have to have the dryer pulled apart in a small space for an extended time i ordered the parts on Friday afternoon and they arrived at my home before noon on Saturday! The contractor and the repairman were able to coordinate the repair on Tuesday morning, and though the... Read more

• Lid or door will not open
• Won't start
• Lid or door won't close

Just removed the old and put on the new,simple.On this Fridgidare washer you should lift the door as you close it which should make the striker last.. Read more

• Shuts off too soon
• Too hot
• Takes too long to dry
• Won't start

Recommendations have fun and a bucket to prevent losing parts. First watch the videos, practice disassemble and reassemble the dryer drum. Make certain you have a good screw driver and spatula from kitchen (could not find my putty knife). Secondly, clean and inspect everything, make sure the motor bearing and belt pulleys are in good condition with little or no play. Third after you have confidently disassembled, vacuum cleaned, inspected all the worn parts, grease the motor and pulley,... Read more

• Will not drain
• Noisy

So, Saturday, the washer wouldn't drain, yes, I tried the Drain/Spin cycle. So I took the clothes out, rinsed them out twice in the laundry sink and dried them. After a quick Google search, I came to the conclusion that the pump was bad and ordered a pump, $125. Over the course of the next four days, expecting the new pump on Thursday, I baled out the washer, pulled it out from the wall and propped up the front (it's HEAVY), removed the front access panel, removed the drain inlet and outlet... Read more

• Marks left on clothes
• Noisy

The dryer is a Kenmore Laundry Center, model 417-99570150. Bought in 1998, so it is an older model. Not wanting to buy the newer ones that are out now. We opted to fix the Kenmore. Just believe the older models are worth fixing, if at all possible. Frist we had to figure out what parts we would need and if the cost would be worth our time. I went on YouTube: and type in Kenmore dryer not turning on. Watched several videos to narrow down the possible problem. Next step was to... Read more

• Spins slowly
• Burning smell
• Pumps but will not spin
• Will not agitate

I replaced the spin bearing, tub seal, washer and drive belt since I had it all apart. The video was extremely helpful...I would have tore the whole thing apart trying to figure out how the agitator came off....but it was very simple. Read more

My 12 year old Frigidaire stack on top dryer had been beeping distress messages in some unintelligible code for about a year when it completely stopped producing heat. It also had a long standing issue with delicate fabrics and thin straps or drawstrings getting caught in the drum. After using this site to troubleshoot and viewing the useful how-to videos, I ordered and replaced the heating element, thermal limiter, and felt seals. Based on others' stories, I decided to also replace the rear... Read more

The very easy diagnosis was motor seizure. Because the machine is about a decade old, I decided to renovate most of the guts. My DIY project included replacing the motor, blower, drum bearing, belt, and door hinge. The end result is a functional dryer with no left-over parts. Lack of parts and hardware challenged the effort. For example, the blower assembly did not have the slide capture for the motor. I had to use the old one which is showing its age. With the exception of the drum... Read more

• No heat or not enough heat
• Takes too long to dry

Being a complete DIY I hate to call some unknown person into my home knowing that just to get them there will cost me more than I will spend for parts that I don't need.After all, they are trying to make a living and by selling me parts that I don't need will increase their profits. I've dealt with APP before and was impressed by their site because I could find both mechanical and electrical drawings for almost everything I have. I looked up my dryer, decided what was probably the problem,... Read more

• Door won't close
• Won't start

The very easy diagnosis was motor seizure. Because the machine is about a decade old, I decided to renovate most of the guts. My DIY project included replacing the motor, blower, drum bearing, belt, and door hinge. The end result is a functional dryer with no left-over parts. Lack of parts and hardware challenged the effort. For example, the blower assembly did not have the slide capture for the motor. I had to use the old one which is showing its age. With the exception of the drum... Read more

Replaced the upper and lower felt strips and drum glides. Dryer running much quieter and not tearing clothes. Read more

• No heat or not enough heat

Being a complete DIY I hate to call some unknown person into my home knowing that just to get them there will cost me more than I will spend for parts that I don't need.After all, they are trying to make a living and by selling me parts that I don't need will increase their profits. I've dealt with APP before and was impressed by their site because I could find both mechanical and electrical drawings for almost everything I have. I looked up my dryer, decided what was probably the problem,... Read more

The dryer is a Kenmore Laundry Center, model 417-99570150. Bought in 1998, so it is an older model. Not wanting to buy the newer ones that are out now. We opted to fix the Kenmore. Just believe the older models are worth fixing, if at all possible. Frist we had to figure out what parts we would need and if the cost would be worth our time. I went on YouTube: and type in Kenmore dryer not turning on. Watched several videos to narrow down the possible problem. Next step was to... Read more

This was a fairly easy fix. The only problem I had was that the cover over the retaining nut was difficult to pull off. I changed to a larger pair of pliers and put a little more muscle to it and it popped right out. There was a little corrosion on the shaft that needed to scraped off for the new agitator to slide on easily but after that was gone the new part slid on and with some downward pressure it seated in. Read more

• Spins slowly

With more difficulty and frustration than expected but it works fine now. Things learned: 1. Order only 3 replacement pins. One comes with the shocks that you can't be sure you see in the picture. 2. A circuit board in a plastic box mounted to the floor, left rear, must be removed by two screws to be able to get pliers onto the head of the pin more easily. This helps installation too. 3. A 1/2" deep socket pushed onto the retaining tab of the pin stays there while you pull with pliers from the... Read more