White Westinghouse Washer Dryer Combo Parts

The Terminal Block is an OEM replacement part for Frigidaire clothes dryers. It is the part the power cord connects to. This kit includes 3 screws and 3 terminals.

Causes of a bad terminal block can include damage from age, overheating from worn wires or loose connections, or improper installation during manufacturing.

Symptoms of a bad terminal block include:

• The dryer not powering on
• Intermittent heating issues
• Loose, frayed, or damaged wires

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

Made to be used on washing machines, this part is a timer. This component controls the electrical parts and the duration of time of the washing machine's cycles. It controls the operation of the washing machine, including each of the cycles.When the timer will not advance, the washing machine could become stuck in a cycle and run constantly without stopping. The washing machine may not advance through the particular cycle like the washing, rinsing, or spinning and could get stuck on one of the cycles. It's important to unplug the washing machine from the electrical outlet before attempting to repair or replace any parts. The replacement process is fairly easy and takes about 15 minutes to complete.This timer is compatible with washing machines that are manufactured by the Frigidaire, Gibson, Kenmore, and White-Westinghouse brands. This part is sold individually and is sourced straight from the manufacturer itself.

This air duct seal creates a tight barrier between the dryer's lint housing and cabinet. Replacing a worn seal helps prevent air leaks, maintain proper airflow through the lint filter, and restore consistent drying performance.

• Seals the air duct/lint housing to the front panel to direct airflow through the lint screen and drum
• Helps maintain dryer efficiency and temperature control by preventing bypass air leaks
• Common symptoms of a failed seal include longer dry times, weak exhaust airflow, excess lint inside the cabinet, or lint around the door opening
• Replaces a deteriorated or missing seal to restore the intended air path

• Disconnect power; shut off gas supply for gas models
• Access the air duct by removing the lint screen and top/front panels as needed
• Remove the old seal and any residue; clean mating surfaces before installing the new seal
• Seat the duct evenly against the panel when reassembling to ensure a uniform seal

This transmission assembly drives the agitation and spin cycles by transferring motor power to the tub. Replacing a worn transmission helps restore proper wash action and spin performance.

• Converts motor rotation into the geared motion needed for wash (agitate) and spin
• Shifts between agitation and spin modes during the cycle
• Common failure signs: no or weak agitation; no spin or slow spin
• Other symptoms include loud grinding/rumbling, oil leaking from the center area, or the motor running while the tub doesn't move

• Disconnect power and water; move the appliance to a stable work area and use proper lifting support
• Access the drive assembly from below; support the tub/frame to prevent tipping
• Mark component orientation, remove fasteners and drive components as needed, and transfer any reusable parts from the original unit
• Tighten mounting hardware evenly, then run a test cycle and check for leaks

For seal only use part number 131901400.

This rubber lid bumper cushions the washer lid to prevent hard contact and reduce noise and wear. It replaces a worn or missing bumper to help the lid close more softly and sit level. What it does:

• Acts as a soft contact point between the lid and cabinet to absorb impact
• Reduces lid slamming, rattling, and vibration during operation
• Helps keep the lid aligned and prevents cosmetic damage to the rim
• Commonly replaced when the bumper is cracked, flattened, or missing

• One rubber lid bumper

• Install by removing the old bumper and pushing the new bumper into the mounting hole or recess; hand tools may be helpful
• Ensure the appliance is powered off and disconnected before servicing
• Inspect surrounding mounting area for damage and replace any broken retainers as needed
• If the bumper is hard to seat, warm it briefly with a hair dryer to improve flexibility

This replacement dryer drum with a galvanized back restores smooth tumbling and helps keep clothes moving and drying evenly. Designed to match the OEM shape and fit for compatible Frigidaire dryers. What it does:

• Replaces a worn, dented or rusted dryer drum so garments tumble properly
• Reduces fabric snags, rubbing marks and uneven drying caused by a damaged drum
• Helps eliminate metal-on-metal noise from a cracked or scored drum surface
• Works with the existing rollers, seals and belt—restores the drum's rotation

• Disconnect power and move the dryer to a clear work area before starting
• Support the drum as you remove the front and rear panels to avoid damage
• Basic hand tools are required; have a helper for heavier lifts
• Inspect rollers, glides and the drive belt during installation and replace if worn