Whirlpool Dispenser Parts

Fix detergent not dispensing or drawer leaking issues with this washer dispenser drawer assembly. Holds detergent and fabric softener during wash cycles.

Color: Black

Black grille that sits at the base of your refrigerator's ice/water dispenser to catch drips. Replace when cracked, stained, loose, or missing.

Color: Midnight Grey

Stainless steel grille that sits on your refrigerator's dispenser drip tray. Replace if cracked, broken, or missing to restore a finished look.

Replaces the lighted paddle you press to dispense water or ice from your refrigerator door. Restores activation when the original pad is cracked, worn, or missing.

Covers and protects the ice container in your refrigerator. Replace if cracked, broken, or missing to keep ice fresh and prevent contamination.

Broken or missing dispenser handle? This assembly restores a solid grip so your washer's dispenser opens smoothly. Easy DIY repair for most models.

White overflow grille for refrigerator water/ice dispenser. Replaces cracked, pitted, discolored, or missing grilles. Snaps into place below dispenser.

Fix washer leaks from the top or bleach not dispensing. This replacement bleach dispenser cup stops drips and restores proper bleaching. 10-min install.

Fix detergent leaking or improper dispensing with a new washer dispenser drawer. Replaces cracked or worn 3-compartment drawers. Easy DIY repair.

This is a replacement refrigerator storage drawer. It restores smooth sliding and dependable storage when the original drawer is cracked, warped, or missing, helping you keep items organized and easy to access. What it does

• Provides enclosed storage for food items inside the refrigerator
• Slides on the existing rails for easy access and organization
• Helps keep contents visible and separated from other items
• Common failure symptoms: cracks, broken tabs, drawer falling off tracks, hard to open/close

• 1 drawer

• Disconnect power and remove items from the drawer area before starting
• Fully extend and lift to remove the old drawer; clean the tracks
• Align the new drawer with both rails and slide it in evenly
• Do not force; ensure tabs and tracks are properly seated

Ice maker not filling properly or water leaking in freezer? A cracked fill cup causes inconsistent fills and leaks. Simple DIY fix guides water correctly.

White plastic grille that sits beneath the ice and water dispenser to catch drips and spills. Replace if cracked, stained, or missing for a clean look.

This replacement door latch engages the strike/catch to keep the door securely closed so the appliance can operate. A worn or broken latch can cause door-closed detection issues, doors that pop open, or cycles that won't start.

• Secures the door by engaging the strike/catch for a positive close
• Ensures door/interlock switches register "door closed" so the unit can run
• Helps maintain a reliable seal and reduces interruptions mid-cycle
• Common symptoms: door won't latch or pops open; appliance won't start; door/latch-related error messages

• Disconnect power to the appliance before servicing
• Note the latch orientation; transfer any original screws/clips as needed
• Align the latch with the strike and tighten fasteners securely
• Close and open the door several times to verify smooth engagement before testing operation

This ice door motor drives the dispenser flap that opens for ice dispensing and closes to seal the chute. Replacing a weak or failed motor restores smooth door movement and helps prevent warm air and moisture from entering the freezer. What it does:

• Actuates the ice chute door during dispensing and returns it closed for a proper seal
• Helps reduce frost, condensation, and ice clumping around the dispenser
• Can address ice not dispensing due to the door not opening/closing
• May resolve clicking or grinding noises from the dispenser area

• Unplug the refrigerator before servicing; wear cut-resistant gloves
• Remove dispenser trim/control panel to access the ice door assembly; handle wiring carefully
• Note linkage and wire orientation before removal to ensure proper reassembly
• After installation, test the dispenser to verify the door opens/closes and seals the chute