Whirlpool Dispenser Parts

The Ice Door is an OEM replacement part compatible with Whirlpool refrigerators. It covers and protects the ice container, ensuring that your ice stays fresh and free from any contaminants and preventing moisture or odors from entering the ice storage container. It features a convenient opening that allows for easy access to the ice whenever you need it.

Symptoms of a faulty ice container door include:

• Loose or broken door
• Difficulty in opening or closing the door
• Improper dispensing of ice

A bad ice container door can occur due to regular use, accidental damage, or wear and tear over time. If you notice issues such as a loose or broken door, difficulty in opening or closing the door, or ice that is not dispensing properly, it may be time to replace the ice container door.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

This dispenser drip tray grille sits on the refrigerator's ice/water dispenser tray. It provides a stable rest for cups and lets drips pass into the tray below, keeping the dispenser area neat with a finished, stainless look.

• Supports glasses and mugs while dispensing ice or water
• Slotted design allows moisture to drain into the tray beneath
• Replaces a cracked, warped, stained, or missing grille
• Restores a clean, factory appearance around the dispenser

• Lock the dispenser or disconnect power before servicing near controls
• Lift out the old grille from the drip tray and clean any debris or mineral buildup
• Place the new grille into the tray; ensure it sits flat and drain openings remain clear
• Avoid abrasive cleaners that can damage the finish

Color: black. Measures about 10 inches wide by 4 inches deep.

Color: White

The Dispenser Drawer Assembly is an OEM component specifically designed for Whirlpool washers. It houses detergent and fabric softener during cycles.

Causes of a faulty assembly can include warping of the plastic base from heat and chemicals over many loads. Small cracks may develop in the detergent trays.  

Symptoms of a bad dispenser drawer assembly include: 

• Leaks from cracked or misaligned drawers polluting washer interiors  
• Difficulty closing or securing the assembly properly
• Premature deterioration inhibiting reliable cycles 

This OEM Whirlpool part is compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore washer models.

This dispenser grille sits in the well beneath your refrigerator's ice and water dispenser. It catches drips and small spills and gives the dispenser area a clean, finished look that's easy to wipe down and keep tidy.

• Collects drips and runoff from dispensing to protect the door surface
• Provides a stable resting surface for cups and bottles
• Removable for quick cleaning and maintenance
• Typical symptoms include cracks, broken tabs, heavy discoloration, or a grille that won't stay seated

• Usually a drop-in replacement: lift out the old grille and set the new one in the dispenser well
• Clean the dispenser well and clear the drain opening before installing
• Align and press down until the grille sits flat; do not force the plastic tabs
• If working around electrical or water components, disconnect power and shut off water for safety

This icemaker fill cup guides incoming water from the refrigerator's inlet tube into the ice mold, helping prevent splashing and freeze-ups during the fill cycle. Replacing a cracked or missing cup restores consistent fills and reduces leaks.

• Directs water from the fill tube straight into the icemaker mold
• Helps prevent overspray, splashing, and ice buildup around the icemaker
• Replace if the cup is cracked, warped, loose, or missing
• Common symptoms: water dripping/freezing under the icemaker, clumped or misshapen cubes

• Unplug the refrigerator and turn off the water supply before servicing
• Remove the icemaker assembly as needed to access the inlet/fill area
• Release the old cup and seat the new cup so the fill tube aligns with the opening
• Restore water and power; check for proper fill and any leaks

This replacement drawer restores a clean, organized storage space inside your refrigerator. It provides a smooth, secure place to hold items so you can access contents easily and maintain the appliance's intended capacity and layout. What it does

• Slides on factory rails/guides to organize food and contain spills
• Restores lost storage capacity when the original drawer is damaged or missing
• Helps contents stay properly supported and easy to access
• Common symptoms: cracked/broken bin, hard-to-slide or misaligned drawer, drawer falls out

• One drawer

• Power down the appliance if working near lights/fans; wear cut-resistant gloves
• Remove items, then lift and pull the old drawer straight out
• Inspect and clear/repair rails or guides before installing the new drawer
• Align with the tracks and slide in until fully seated; do not force

This replacement door latch engages the strike/catch to keep the door securely closed so the appliance can operate. A worn or broken latch can cause door-closed detection issues, doors that pop open, or cycles that won't start.

• Secures the door by engaging the strike/catch for a positive close
• Ensures door/interlock switches register "door closed" so the unit can run
• Helps maintain a reliable seal and reduces interruptions mid-cycle
• Common symptoms: door won't latch or pops open; appliance won't start; door/latch-related error messages

• Disconnect power to the appliance before servicing
• Note the latch orientation; transfer any original screws/clips as needed
• Align the latch with the strike and tighten fasteners securely
• Close and open the door several times to verify smooth engagement before testing operation

This refrigerator ice guide channels cubes and crushed ice along the intended path so they land in your bin or glass. When the guide is damaged or missing, ice can scatter, jam, or miss the dispenser opening. What it does

• Guides ice from the ice maker/bucket into the bin and through the dispenser chute
• Helps keep ice flowing smoothly and reduces spills at the opening
• Restores proper aim for cubed and crushed ice
• Typical symptoms: ice spraying or missing the glass, frequent jams, or visible damage to the guide

• 1 ice guide

• Disconnect power to the refrigerator before servicing
• Remove the ice bin and access the guide per your model's design
• Transfer and reuse existing mounting screws or clips, if applicable
• Verify alignment, then test both cubed and crushed dispensing

This replacement dispenser drawer restores smooth operation and proper dispensing of detergent, bleach, and fabric softener in your washer. It helps prevent leaks and residue when the original drawer is cracked, warped, or difficult to open and close. What it does:

• Holds and meters detergent, bleach, and fabric softener into the wash at the correct time
• Helps ensure additives mix with water and flow into the tub, not onto the cabinet front
• Direct replacement for drawers with broken handles, cracks, or swelling
• Common symptoms: leaking at the drawer area, poor dispensing, leftover detergent, or a stuck drawer

• Includes: 1 dispenser drawer assembly

• Disconnect power and turn off water before servicing
• Pull the drawer out fully and depress the release tab to remove
• Transfer any removable siphon caps or inserts from the old drawer
• Clean the dispenser housing channels, then slide in the new drawer and run a test cycle to check for leaks

This dispenser assembly replaces a refrigerator's door-mounted ice and water dispenser to restore normal dispensing and reduce leaks or delivery issues. It provides the core housing and user-facing dispenser opening for door-based dispensing systems. What it does:

• Directs water and ice from the door dispenser to the user, forming the visible dispensing opening and housing.
• Helps stop common dispenser symptoms such as water dripping from the dispenser opening or ice/jam buildup at the dispenser chute.
• Supports normal push-lever or paddle operation and routes water/ice to the exterior dispense area.

• Disconnect power and shut off the water supply before starting any work.
• Removal typically requires taking off the refrigerator door panel or trim to access mounting fasteners—retain all hardware and note fastener locations.
• Handle the dispenser housing carefully to avoid cracking plastic or damaging seals; inspect gaskets and fittings and replace if brittle.

This ice door motor drives the dispenser flap that opens for ice dispensing and closes to seal the chute. Replacing a weak or failed motor restores smooth door movement and helps prevent warm air and moisture from entering the freezer. What it does:

• Actuates the ice chute door during dispensing and returns it closed for a proper seal
• Helps reduce frost, condensation, and ice clumping around the dispenser
• Can address ice not dispensing due to the door not opening/closing
• May resolve clicking or grinding noises from the dispenser area

• Unplug the refrigerator before servicing; wear cut-resistant gloves
• Remove dispenser trim/control panel to access the ice door assembly; handle wiring carefully
• Note linkage and wire orientation before removal to ensure proper reassembly
• After installation, test the dispenser to verify the door opens/closes and seals the chute

This dispenser stores the detergent and rinse aid and releases them at the proper time during the cycle, helping your dishwasher clean effectively and reduce spotting. Replacing a faulty dispenser restores consistent soap release and rinse performance. What it does:

• Holds detergent and rinse aid, then opens to release them at the correct stage of the wash
• Helps prevent detergent remaining in the cup after a cycle
• Restores proper latching and sealing of the dispenser door
• Common fix for a cracked housing, broken latch, or rinse aid leaking/over-dispensing

• 1 dispenser assembly

• Disconnect power to the dishwasher before servicing
• Remove inner door panel fasteners to access the dispenser; disconnect the electrical connector
• Release the locking tabs, remove the old dispenser, and seat the new one evenly to ensure a proper seal
• Reassemble the door, restore power, and run a short cycle to check for leaks and proper operation

This lighted dispenser actuator pad assembly replaces the extra-large paddle you press to dispense water or ice from the door. It restores smooth, reliable activation and visibility when the original pad is cracked, worn, or unresponsive.

• Acts as the user-pressed paddle that engages the dispenser switch for water/ice
• Integrated illumination helps light the dispenser alcove for easier use in low light
• Helps address intermittent dispensing, sticking or continuous dispensing, or the need to press excessively hard
• Replaces broken, loose, or discolored paddles for better function and appearance

• Disconnect power before servicing the dispenser area
• Remove the drip tray and dispenser trim/escutcheon to access the pad assembly
• Release retaining tabs/screws and disconnect any wire harnesses; note orientation
• Install the new assembly, reconnect wiring, reassemble trim, restore power, and test dispensing and lighting

Keep your batch-feed disposer operating safely and easily. This actuator handle inserts into the sink opening to start and stop the disposer and also functions as the sink stopper on batch-feed models, replacing cracked, worn, or missing handles.

• Engages the internal switch to start/stop the disposer when inserted and rotated
• Provides a secure grip for controlled batch-feed operation
• Helps seal the drain to hold water in the sink between uses
• Symptoms include: disposer won't run or runs intermittently with the handle inserted, handle is cracked/loose, or won't lock/turn to engage

• Disconnect power to the disposer before testing or handling parts
• Ensure the sink opening and splash guard are clear so the handle seats fully
• Insert the handle into the drain, align/press down, and rotate per your owner's manual to engage; reverse to stop
• Never place hands inside the disposer; use tongs/pliers to remove objects

This small pad fits under a cooktop/range burner grate to cushion and stabilize it, helping prevent wobble and surface scratches. Replacing worn or missing pads keeps the grate level and protects the cooktop finish. What it does:

• Supports and levels the burner grate at its contact points
• Reduces rattling and movement during cooking
• Helps prevent metal-on-metal scraping and scratches on the cooktop
• Replace if pads are missing, flattened, brittle, or the grate rocks

• 1 pad

• Allow the appliance and grates to cool completely; disconnect power/gas if servicing near burners
• Remove the grate; clean old pad residue and thoroughly dry the contact area
• Press the new pad firmly into place; replace all pads on a grate for even height
• Avoid harsh solvents that can damage enamel or stainless finishes