Whirlpool Dispenser Parts

This dispenser is the door-mounted assembly that delivers ice and/or water from the refrigerator. It replaces a worn, cracked, or malfunctioning dispenser to restore normal dispensing and stop leaks. What it does:

• Provides a finished dispenser opening and support for the actuator and chute so water and ice flow correctly.
• Stops leaks and prevents food or debris from entering the dispenser area when cracked or damaged.
• Restores proper activation when the dispenser lever or paddle no longer engages the valve or auger.
• Helps eliminate jams or misalignment that can cause intermittent dispensing or noisy operation.

• Disconnect power and shut off the water supply before starting any work.
• Remove the inner door panel or trim to access the dispenser mounting screws and wiring.
• Handle gently to avoid cracking surrounding trim; test operation before reassembling the door.

This dishwasher dispenser stores detergent and rinse aid and releases them at the correct points in the cycle to support consistent cleaning results. Replace a broken, stuck, or leaking dispenser to restore reliable detergent delivery.

• Holds detergent and rinse aid and dispenses them automatically during the wash and rinse portions of the cycle
• Door/actuator mechanism controls the timed release of detergent
• Seals help prevent leaks around the dispenser opening
• Typical failure symptoms: detergent cup won't latch or open, detergent left in the cup, rinse aid not dispensing, or leaks from the dispenser area

• Disconnect power and turn off water supply before servicing
• Remove the inner door panel to access the dispenser; disconnect the wire connector
• Release mounting screws/clips, clean the door cutout, and seat the new dispenser evenly
• Tighten screws in a cross pattern to compress the gasket uniformly; run a test cycle to check for leaks and proper operation

This is the pull-out dispenser drawer assembly for a washer. It holds and channels laundry products into the dispenser housing so each additive is released at the right time, restoring smooth operation and proper dispensing. What it does:

• Holds detergent and additives and directs them into the wash at the correct stage
• Restores smooth open/close action of a worn or broken drawer
• Helps resolve issues like detergent remaining in the drawer after a cycle
• Addresses leaks or drips from a cracked or warped dispenser drawer

• 1 dispenser drawer assembly

• Unplug the washer and turn off water supply before servicing
• Pull the old drawer out; depress the locking tab(s) to remove
• Transfer any reusable inserts/caps from the original drawer if applicable
• Slide the new drawer into the rails until it clicks; run a quick cycle to check for proper dispensing and leaks

The Dispenser Drawer Handle is an OEM part for Whirlpool washing machines. The white handle allows users to easily access the detergent dispenser drawer at the beginning of the wash cycle. 

Causes of a bad handle can include worn or stripped mounting areas that no longer provide a stable grip, cracks or breaks in the plastic material, or missing/damaged spring components that assist in closing the drawer. 

Symptoms of a bad handle include:

• Difficulty opening the dispenser drawer 
• The handle no longer stays securely in place when opening the drawer
• Inability to fully open or close the dispenser drawer

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This is the lid assembly for the dispenser. It covers and protects the dispenser compartment, helping keep debris out and ensuring the dispenser opens and closes properly.

• Covers the dispenser compartment to prevent spills and contamination
• Helps ensure proper dispenser operation
• Common fix when the dispenser lid is cracked, broken, loose, or won't stay closed

• Disconnect power and shut off water before servicing
• Open the dispenser area and remove any retaining screws or tabs
• Transfer any reusable hardware from the old lid to the new assembly
• Test operation before returning the appliance to service

This replacement cover restores the appliance's exterior protection and appearance by shielding internal components and helping maintain safe operation. Designed to match the original form and mounting points for a direct-fit replacement. What it does:

• Shields internal parts from dust, spills and accidental contact.
• Helps keep wiring and controls securely enclosed to reduce risk of damage.
• Restores a flush, finished exterior when the original cover is cracked, broken or missing.
• Prevents rattling or snagging caused by loose or damaged panels.

• Disconnect power (unplug or shut off breaker) before starting any work.
• Installation typically requires basic hand tools (screwdriver/socket); follow factory service instructions for fastener locations.
• Handle edges carefully—parts may have sharp edges; support the panel during removal/installation to avoid scratches or dropped hardware.
• Reinstall all fasteners snugly but avoid over-torquing; verify panels align and clear moving parts before restoring power.

The Divider is an OEM part for Whirlpool washers. It fits within the dispenser drawer, creating separate compartments for different laundry products such as detergent, fabric softener, and bleach. It prevents mixing and allows for convenient dispensing during each wash cycle.

A bad dispenser drawer divider can occur due to wear and tear over time or accidental damage. If you notice symptoms such as a loose or broken divider, difficulty in separating the compartments, or improper dispensing of laundry products, it may be time to replace this part.

Symptoms of a bad dispenser drawer divider include:

• Loose or broken divider
• Difficulty in separating the compartments
• Improper dispensing of laundry products

Restore your Whirlpool washer's dispenser drawer by replacing the faulty or damaged divider with this genuine OEM part.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
 

The Dispenser Drawer Handle is an OEM part compatible with Whirlpool washers. It provides a convenient grip for opening and closing the dispenser drawer. It allows you to access the detergent, fabric softener, and bleach compartments within the dispenser drawer.

A bad dispenser drawer handle can occur due to wear and tear, accidental damage, or excessive force when operating the handle. If you notice symptoms such as a loose or broken handle, difficulty in opening or closing the dispenser drawer, or the handle not staying securely in place, it may be time to replace this part.

Symptoms of a bad dispenser drawer handle include:

• Loose or broken handle
• Difficulty in opening or closing the dispenser drawer
• Handle not staying securely in place

Restore your Whirlpool washer's dispenser drawer by replacing the faulty or damaged handle with this genuine OEM part.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
 

This bi-metal is the thermal actuator that releases the detergent dispenser at the proper point in the wash cycle. Replacing a weak or failed actuator restores reliable detergent cup opening and consistent detergent delivery for better cleaning. What it does:

• Heats and flexes when energized by the control to trip the dispenser latch
• If failed, the detergent cup may not open or may open inconsistently
• Can leave detergent in the cup and lead to poor cleaning results
• Often suspected when the cycle runs but the soap door stays closed

• 1 bi-metal actuator assembly

• Disconnect power at the breaker before servicing
• Remove the inner door panel to access the dispenser area
• Note wiring positions and orientation; transfer connectors securely to the new actuator
• The dispenser latch/linkage moves freely and test door release before reassembly

This wet agent dispenser replaces the washer's liquid fabric softener dispenser to restore proper dispensing during the rinse cycle. It helps keep softener contained until the machine is ready to release it, improving rinse-time performance. What it does:

• Holds and releases liquid fabric softener (wet agent) into the rinse cycle
• Ensures softener is delivered at the correct time for even distribution
• Stops leaking or premature release when the dispenser housing is intact
• Commonly replaced when the dispenser cracks, clogs, or fails to dispense

• Disconnect power to the appliance before starting any repairs
• Access method varies by model; remove dispenser drawer or top panel per your model's service instructions
• Inspect surrounding seals and clips; replace if damaged to prevent leaks

This replacement housing restores the appliance's structural enclosure, protecting internal components and helping panels and controls align properly. Use it to replace cracked, warped or damaged housings so the unit fits and functions as intended. What it does:

• Provides the main structural enclosure and mounting surface for internal components and exterior panels
• Replaces cracked, dented or broken housings that can allow misalignment or rubbing of parts
• Helps reduce vibration and movement by restoring proper fit between panels and internal assemblies
• Keeps internal components shielded from debris and wear that can lead to downstream issues

• Disconnect power (and water, if applicable) before starting any repair
• Handle edges carefully; housing edges and sheet metal can be sharp
• Basic hand tools are typically required; follow the appliance service manual for disassembly/reassembly steps

This dispenser facade replaces the outer trim pieces around your refrigerator's ice and water dispenser, restoring appearance and proper fit for smooth operation and sealing. It's a direct-fit cosmetic and protective assembly. What it does:

• Covers and protects the dispenser opening and controls from damage and debris
• Provides a finished look and helps direct water/ice into the cup
• Restores proper alignment when cracked, warped, or broken facade causes interference
• Helps prevent drafts and minor water splash at the dispenser area

• Disconnect power and shut off water to the appliance before servicing
• Many installations require removing the dispenser bezel and releasing snap-clips or screws; save hardware for reinstallation
• Handle plastic trim carefully to avoid scratches; use a soft pad when setting parts down

This outer trim panel cover replaces a cracked, broken or missing exterior cover to protect internal components and restore the appliance's finished appearance. It fits where the factory cover shields wiring and mounting points. What it does:

• Protects wiring, switches and internal parts from debris and accidental contact
• Restores the appliance's exterior finish and prevents drafts or gaps
• Stops rattling or vibration caused by damaged or loose trim
• Helps keep moisture and dust out of sensitive areas

• Disconnect power to the appliance before starting any repair.
• Remove any adjacent panels or fasteners to access the cover; retain screws and clips for reassembly.
• Align cover tabs and secure with original screws or clips; do not force or overtighten to avoid cracking.
• Replace those parts before finishing the repair.

This wet agent dispenser assembly holds and releases liquid wetting/conditioning agents into the wash at the correct cycle, helping deliver fabric conditioner or similar additives when needed. It replaces a worn, clogged, or damaged dispenser for reliable delivery. What it does:

• Holds liquid fabric conditioner/wetting agent and releases it into the tub during the rinse cycle
• Ensures timed dispensing so conditioners are added at the proper point in the cycle
• Helps prevent over-dispensing and visible residue in the washer tub or on clothes
• Commonly replaces dispensers that leak, fail to release liquid, or have broken mounting tabs

• One wet agent dispenser assembly

• Disconnect power to the appliance before beginning any work
• Remove and reinstall using basic hand tools
• Rinse any remaining liquid from the area and avoid skin/eye contact with chemicals
• Test a short cycle after installation to ensure proper dispensing and secure mounting

This dispenser handle assembly restores proper operation and control of your refrigerator's ice and water dispenser. It replaces a cracked, loose, or broken handle so you can dispense without difficulty and improve the dispenser's appearance. What it does

• Replaces damaged or cracked dispenser handle so the lever engages properly
• Provides a secure grip for activating the ice and water dispenser
• Helps stop wobbling or sticking that prevents consistent dispensing
• Restores alignment and tactile feedback for dispenser operation

• Disconnect power to the refrigerator before starting any work to avoid electrical hazard.
• Remove the old handle by accessing the dispenser trim and fasteners; retain mounting screws if reusing.
• Align the new handle, secure fasteners, and verify the dispenser lever moves freely and dispenses correctly.

This dispenser is the exterior door component that delivers chilled water and/or ice from the refrigerator, restoring normal dispensing and preventing drips or jams. It replaces a damaged, cracked or non-functioning door dispenser. What it does

• Guides water and ice from the internal plumbing to the exterior spout so items can be dispensed from the door.
• Re-establishes a secure spout and actuator for reliable dispensing and reduced leaks.
• Stops common dispenser symptoms such as leaking at the door, stuck or loose dispenser lever, and misaligned spout.
• Helps restore normal dispensing when the door dispenser is cracked, broken, or no longer seating properly.

• One dispenser assembly.

• Disconnect power and shut off the refrigerator water supply before beginning.
• Remove the interior door panel and any trim to access the dispenser assembly; keep fasteners organized for reassembly.
• Inspect and replace any worn gaskets or seals to prevent leaks; ensure proper hose routing.
• Test operation and check for leaks after reconnecting power and water.