Whirlpool Dispenser Parts

Also order retainer part number WP3400918

The Dispenser Tray is an OEM part for Whirlpool top-loading washing machines. Located inside the detergent drawer, this durable molded tray is designed to hold liquid detergent packs safely in place during cycles. Its size and dimensions facilitate convenient single-dose placement.

Causes for replacement may include cracks, warping, or discoloration due to mineral buildup affecting the tray structure over time.

Symptoms of a faulty tray involve:  

• Difficulty loading or securing detergent packs properly   
• Leaks or spills of detergent inside the drawer compartment
• Off-center or displaced detergent dosing during the wash

This OEM Whirlpool replacement is compatible with select Whirlpool, Maytag, and other major brand front-loaders.

The Detergent Dispenser Drawer is an OEM part for Whirlpool washing machines. It plays a crucial role in dispensing detergent during the wash cycle. The drawer is designed to hold and release the appropriate amount of detergent at the right time, ensuring optimal cleaning performance. 

Symptoms of a bad dispenser drawer include:

• Improper dispensing of detergent  
• Insufficient cleaning results
• Leaks or drips from the dispenser area
• The drawer not opening or closing correctly

Causes of a bad dispenser drawer can include clogging or blockage in the drawer mechanism, damage to the drawer or latch, or malfunctioning electronic components that control the dispensing process. 

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Dispenser Drawer Assembly is an OEM part for Whirlpool front-loading washing machines. The drawer houses mechanisms that deposit detergent and fabric softener into the drum at the proper times in the wash cycle. 

Causes of a bad dispenser drawer can include wear and tear to runners, rollers, or linkage connecting it to the washer cabinet over repeated use. Mineral or chemical deposits may also jam drawer movement.

Symptoms of a bad dispenser drawer include: 

• Failure to fully retract or extend from the cabinet
• Difficulty latching or staying securely closed  
• Contents not fully dispensing into the drum
• Inconsistent or improper distribution of detergent

This OEM Whirlpool replacement drawer assembly is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore front-loading washing machines. 

Replacement drip tray that collects and channels defrost and condensation water away from the cabinet to help prevent puddles and water damage. Sits under the freezer/drain area to guide meltwater to the evaporator or drain. What it does:

• Collects defrost and condensation water to prevent leaks and pooling beneath the appliance.
• Directs meltwater toward the evaporator/drain so it can evaporate safely.
• Helps reduce odors and ice buildup caused by standing water.
• Common signs you may need this part: water pooling under or behind the appliance, visible cracks or warped pan, or ice forming where water should drain.

• One drip tray

• Disconnect power before accessing the tray and remove any stored items from nearby compartments.
• Tray is typically accessed from the rear or behind the lower grille/panel—remove the appropriate access panel first.
• Inspect the drain channel for clogs or debris before installing the new tray and seat the pan flat to ensure proper drainage.
• Replace the tray if you see cracks, warping, or severe corrosion; use only manufacturer-recommended parts.

The Dispenser Funnel Guide Ice Door is an OEM part for Whirlpool refrigerators. It is responsible for guiding ice from the ice dispenser on the door into your glass.

A bad dispenser funnel guide ice door can occur due to regular use, wear and tear, or damage caused by foreign objects. If you notice ice not dispensing properly or falling outside of your glass, it may indicate a problem with the dispenser funnel guide ice door.

Symptoms of a bad dispenser funnel guide ice door include:

• Ice not dispensing into the glass or container properly
• Ice falling outside of the glass during dispensing
• Difficulty in activating the ice dispenser or inconsistent ice flow

This Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

The Thermostat Housing is an OEM part for Whirlpool dishwashers. It encases the thermostat responsible for accurately monitoring water temperatures throughout cleaning cycles. 

Symptoms of a faulty housing include:

• Inconsistent or improper water heating  
• Delayed or incomplete cycles from temperature control issues
• Error codes or failure detection by the control board

Causes may involve cracks allowing steam penetration, loose mounting points compromising seals, or damaged seals leaking interior thermostat components. 

This OEM replacement fits Whirlpool, KitchenAid, Jenn-Air, and some Kenmore models as well.

Drip tray that catches defrost and condensation water to prevent leaks and floor damage. Replaces a cracked or missing tray to restore proper water collection and reduce standing water beneath the appliance. What it does:

• Collects melted frost and condensation from the cooling system so water is contained and managed.
• Channels water toward the appliance's evaporation/drain area so it can evaporate safely.
• Helps prevent puddles and potential floor damage caused by a damaged or missing tray.
• Replace when tray is cracked, warped, leaking, or shows visible damage.

• Disconnect power to the appliance before performing any service.
• Access is typically through the lower toe grille or a rear access panel.
• Inspect mounting tabs and surrounding supports for damage and ensure the new tray seats properly.
• Wear gloves and take care around sharp sheet-metal edges during removal/install.

Color: Grey

This dispenser is the front housing that channels ice and water from the refrigerator to the user, restoring proper dispensing and a finished appearance. It fits into the refrigerator door and works with the dispenser controls. What it does:

• Directs and channels ice and water from the internal supply to the exterior dispenser opening
• Provides the mounting surface and openings for dispenser controls, actuator/lever, and chute
• Helps prevent leaks and misdirected water when the dispenser is working correctly
• Commonly replaced for cracked housing, broken mounting tabs, or cosmetic damage that affects dispensing

• One dispenser housing assembly

• Disconnect power and turn off the water supply before starting any repair
• Handle plastic clips and tabs carefully during removal to avoid breakage
• Reuse any electronic components only if compatible; replace damaged clips or seals
• After installation, turn on water and power and check for proper operation and leaks

The Tank is an OEM part for Whirlpool washing machines. It properly dispenses detergent during the wash cycle.

Causes of a bad detergent tank can include: cracks, holes or other damage that cause leakage or improper detergent dispensing. Scaling or mineral buildup inside the tank over time may also lead to detergent dispensing issues.

Symptoms of a bad detergent tank include:

• Detergent not being fully dispensed or released during the wash
• Residue or leftover detergent remaining in the tank after cycles
• Clothes not getting properly cleaned due to insufficient detergent release

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Dispenser Drawer is an OEM component specifically designed for Whirlpool washing machines. It provides a contained area to safely add detergent and fabric softener during wash cycles.  

Symptoms of a bad dispenser drawer include:

• Inability to open or close smoothly
• Cracks or breaks in the plastic housing
• Leaks or spills from seals no longer fully containing liquids

Causes can relate to mineral buildup corroding moving parts, cracks developing from repeated opening/closing, or impact issues distorting the structural integrity of the design.

Color: Chrome Shadow

This OEM replacement dispenser drawer is designed to directly replace the worn original. Compatible models include those from brands such as Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore. 

The Icemaker Fill Cup is an OEM part for Whirlpool bottom-mount and side-by-side refrigerators. Located inside the icemaker assembly, the fill cup sensor works to automatically detect when an ice scoop or bucket is in place below the icemaker chute. It signals the icemaker to drop ice cubes into the receptacle below.

Causes of a bad fill cup sensor can include mineral or dirt build-up inhibiting sensor response, moisture damage to its electronic functioning, or physical damage to the sensor head.

Symptoms of a bad fill cup sensor include:

• Ice failing to dispense or drop when a container is in place
• Ice clumping in the chute instead of dispensing properly  
• The icemaker continuing to run even with ice present below
• Inability to sense when ice is removed from the bucket

This OEM Whirlpool replacement fill cup sensor is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore bottom-mount and side-by-side refrigerators.