Whirlpool Hose Or Tube

This water tube connector joins sections of your refrigerator's water line for the dispenser and ice maker. It restores a secure, leak-resistant connection when the original coupling is damaged or leaking.

• Connects two segments of refrigerator water tubing
• Helps maintain proper water flow to dispenser and ice maker
• Resolves leaks caused by a cracked, worn, or loose connector
• Useful when replacing or rerouting water lines during service

• Disconnect power and shut off the water supply before servicing
• Dispense water to relieve line pressure
• Cut tubing square and insert fully until seated; tug gently to confirm a secure fit
• Restore water and check all connections for leaks; replace any damaged tubing as needed

This collar kit renews the quick-connect faucet interface on select portable appliances, restoring a secure, leak-resistant connection at the sink. Replace a stripped, cracked, or missing collar to stop drips and ensure the coupler attaches smoothly.

• Provides the correct shoulder/threads for the quick-connect coupler or adapter
• Helps seal the faucet connection to reduce leaks and spray
• Replaces worn, damaged, or missing collar in the connector assembly
• Common symptoms: leaking at the faucet, coupler won't latch or pops off, loose connection

• Turn off water and disconnect the appliance from the faucet before service
• Relieve hose pressure and place a towel under the work area
• Remove the existing collar and clean faucet threads before installing the new one
• Hand-tighten only; avoid overtightening and check for leaks on first use

The Water Tube is an OEM part for Whirlpool refrigerators. It is responsible for transporting water from the water valve to the back of the refrigerator. The water tube allows for easy access to chilled and filtered drinking water directly from the refrigerator dispenser.

Causes of a bad water tube can be cracks, kinks, or damage developing over time due to regular use and repetitive bending during cleaning. Mineral deposits may also cause restrictions.

Symptoms of a bad water tube include:

• Water leaks or spraying inside the refrigerator
• Low water pressure from the dispenser
• Dispenser malfunctions or does not work
• Dripping or pooling water near the tube connection points

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This adjustable manifold connects the upper rack to the dishwasher's rear water feed. It channels wash water to the upper spray arm and maintains a sealed connection as the rack height changes for consistent cleaning performance. What it does:

• Routes water from the rear feed tube to the upper/middle spray arm
• Self-adjusts with rack position to keep a secure, leak-resistant connection
• Replace if cracked, deformed, or the coupling no longer seals
• Common symptoms include poor cleaning on the upper rack, weak spray, upper spray arm not turning, or a small leak at the back of the tub

• 1 adjustable manifold

• Disconnect power and shut off water; wear gloves for protection
• Remove the upper rack by releasing the rail end caps and sliding the rack out
• Unclip the manifold from the rack and disengage it from the rear feed port; seat the new manifold fully
• Reinstall the rack and ensure the spray arm spins freely

Extends the drain hose approximately 4 feet. You must also order a drain hose connector kit: 285835.

12 Ft in length

These inserts are for 1/4 inch plastic tubing. Package of 4.

Water tube connector that joins two sections of a refrigerator's water tubing for a secure, leak-resistant connection. Replacing a cracked or leaking connector can help restore consistent water flow to the dispenser and ice maker.

• Connects two lengths of refrigerator water tubing in the supply, filter, dispenser, or ice maker circuit
• Helps maintain a sealed connection to reduce leaks and air intrusion
• Common symptoms of failure: dripping at the fitting, water under the unit, weak/no dispensing, or ice maker not filling
• Replace if the connector is cracked or will not hold tubing securely

• Unplug the refrigerator and shut off the water supply
• Dispense water to relieve line pressure; place a towel under the connection
• Cut tube ends square; push each tube fully into the connector until seated, then tug gently to confirm engagement
• Restore water and check carefully for leaks before reconnecting power

This drain tube directs defrost/condensate water from the appliance's drain outlet into the drain pan, helping prevent water from pooling inside the cabinet or leaking onto the floor for reliable, mess-free operation. What it does:

• Channels defrost/condensate water from the drain outlet to the pan
• Helps prevent interior leaks, puddles beneath the unit, and ice at the drain
• Restores proper drainage when the original tube is cracked, misshapen, or clogged
• Addresses symptoms like water under drawers/shelves or musty odors from standing water

• 1 drain tube

• Disconnect power and pull the unit forward for rear access; turn off water supply if applicable
• Remove the old tube and clear any debris/ice from the drain opening
• Fully seat the new tube on the drain outlet and position the outlet over the pan, following original routing
• Test by pouring a small amount of warm water into the drain to ensure proper flow and no leaks

The Drain Hose is an OEM part for Whirlpool dishwashers. This hose works to divert wastewater from the dishwasher to the garbage disposal or drain pipe beneath the kitchen sink.

The drain hose is responsible for safely transporting soapy water, food debris and other particles away from the washing cavity during each cycle. It prevents leaks and backup within the dishwasher tub.

Causes of a bad drain hose can include cracks, splitting, or deterioration of the plastic tubing over many years of use. Clogs within the hose are also problematic.

Symptoms of a failed drain hose include:

• Puddles or leaks developing beneath the dishwasher
• Inability to fully drain wash and rinse water after cycles
• Fault codes showing drainage issues

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Includes connector and both clamps.

Replacement fill hose that routes water from the household supply to the appliance's ice maker and water dispenser, restoring proper water delivery and helping prevent leaks or pooling from a damaged line. What it does

• Directs water from the inlet valve to the ice maker and dispenser for ice production and dispensing.
• Maintains steady water flow; prevents kinks and pinched lines that reduce flow.
• Replace if cracked, split, collapsed, or leaking.
• Common symptoms: reduced or no water to the dispenser or ice maker, visible leaks, or pooling under/behind the appliance.

• Turn off the water supply and disconnect power before servicing to avoid flooding and electrical hazard.
• Inspect and replace clamps or fittings as needed; ensure proper seating and a snug, leak-free connection without overtightening.
• Check for kinks in the hose and route it so it won't be pinched by the appliance or cabinetry.
• After installation, turn the water back on and test for leaks at all connections.

Contains two, six foot long braided hoses with 90 degree ends.

This set of washer fill hoses connects your home's hot and cold water supply to the washer's inlet valves. Replacing aging hoses helps prevent leaks and ensures the washer fills properly for every cycle.

• Supplies hot and cold water from household faucets to the washer's inlet valves
• Helps address leaks, bulges, or cracks in old hoses
• Can resolve drips at fittings and water on the floor
• Improve slow or no-fill issues caused by kinks or internal blockages

• Unplug the washer and turn off both water supplies before starting
• Place a towel or pan to catch residual water; disconnect old hoses from faucets and inlet valves
• Attach new hoses to the correct hot/cold connections; tighten connections securely without overtightening
• Open valves, check for leaks at both ends, and re-tighten if needed

Size: 7 foot long.

Size: 8 foot long. This external washer drain hose is needed when there is more distance between the washer and the drain. Note: comes with 1.5" diameter clamp but hose is 1.25" in diameter; therefore you may need to order the 1.25" diameter clamp separately: WP356138