Whirlpool Hose Or Tube

A direct-replacement inlet tube that routes incoming water from the valve to the appliance tub. Restores proper water flow and prevents leaks for reliable fills and cycles. What it does

• Channels water from the fill valve to the appliance tub or wash chamber.
• Replaces cracked, split, or deteriorated tubing that causes leaks.
• Helps resolve no-fill or slow-fill symptoms when the valve and hoses are intact.
• Prevents water pooling and potential water damage from failed tubing.

• Disconnect power and shut off the water supply before starting.
• Inspect and reuse or replace any clamps, seals, or grommets as needed.
• Verify correct orientation and seating to avoid kinks or strain on connections.
• Use basic hand tools; test for leaks after reassembly.

This adjustable manifold is a direct-fit replacement that secures and positions the appliance's manifold assembly so related components line up and function correctly. It restores proper alignment and reliable operation when the original is bent or worn. What it does:

• Provides a mounting surface and adjustable position for the manifold assembly and attached components
• Helps maintain correct alignment so burners/valves operate smoothly
• Restores fit when the original manifold is damaged, bent, or loose
• Resolves symptoms such as uneven burner operation, ignition difficulty, or mechanical misalignment

• Turn off power and shut off gas supply before starting work
• Handle and align carefully to avoid bending; secure with the OEM fasteners
• Check seals and connections after installation; test operation per manufacturer instructions

This hose kit replaces worn or damaged appliance hoses to restore proper water flow and prevent leaks. It's a direct-fit replacement for compatible Whirlpool systems and helps stop visible leaks and restore normal fill/drain operation. What it does

• Replaces cracked, split or leaking hoses to stop water loss and reduce risk of appliance damage
• Restores reliable water flow for filling and draining functions
• Helps eliminate poor draining, intermittent filling, or water pooling near the appliance
• Works with existing clamps and connections when installed correctly

• Disconnect power and shut off the water supply before starting any repair
• Inspect connection fittings and replace clamps if worn; ensure a snug, leak-free fit
• Route hoses without kinks and secure to avoid chafing or strain
• After installation, run a short cycle and check all connections for leaks

This replacement water dispenser valve tube routes water from the dispenser valve to the dispenser outlet so your appliance can deliver water and ice correctly. It restores a proper, leak-free flow path for the dispenser. What it does:

• Connects the dispenser valve to the dispenser outlet, directing water flow for dispensing and ice-making functions
• Replaces cracked, pinched, or deteriorated tubing that can cause leaks or weak/blocked water flow
• Helps stop visible leaks under the dispenser area and restore normal dispensing performance
• Compatible with factory valve connections and dispenser fittings when the OEM tube is specified

• One replacement water dispenser valve tube

• Disconnect power and shut off the water supply before starting work
• Inspect matching fittings and clamps; reuse only if undamaged — replace clamps if corroded
• Route the tube following factory routing to avoid kinks and ensure secure connections

This dispenser hose routes water from the refrigerator's valve to the dispenser and ice maker, helping restore proper water delivery and prevent leaks or drips at the dispenser. Use as a direct replacement for damaged or leaking lines. What it does:

• Carries water from the inlet valve to the dispenser and ice system
• Replaces cracked, split, or kinked tubing that causes leaks
• Can resolve weak or intermittent dispenser flow caused by restricted or collapsed hose
• Helps prevent water damage by restoring a sealed, secure connection

• Shut off the refrigerator's water supply and disconnect power before starting
• Inspect fittings and clamps; replace any corroded or damaged hardware
• Route hose without sharp bends or kinks and secure with proper clamps
• Turn water back on and check all connections for leaks before restoring normal use

Kit contains two 10 feet inlet hoses.

Size: 6 foot long. Washers not included. This is one hose, for a set with washers order 285363. For inlet hose screen use 285452A and for inlet hose washers use 285448A

This dishwasher drain hose kit includes a clamp with instructions.

This tube union connector joins two water or refrigerant tubes to restore a sealed flow path and stop leaks. It's a direct-replacement plumbing fitting used on refrigerators and ice/water systems. What it does

• Joins two sections of tubing to maintain a sealed water line connection.
• Restores proper water flow to the dispenser or ice maker when a damaged union causes leaks or loss of supply.
• Provides a threaded/press-fit junction to prevent drips and reduce pressure loss.
• Helps avoid water damage from a cracked or corroded tube joint.

• One tube union connector

• Turn off the water supply and unplug the appliance before starting work.
• Confirm tube sizes and connection type before installation; tighten fittings per manufacturer guidance to avoid overtightening.
• Inspect tubing ends for damage and cut squarely if needed for a proper seal.
• After installation, restore water and power, then check the connection carefully for leaks.

This collector hose assembly routes and channels water inside the appliance to the drain area, helping maintain proper water flow during cycles. It replaces worn, cracked, or leaking collector hoses to reduce leaks and maintain performance. What it does:

• Channels wastewater from internal tub components to the drain system
• Helps prevent leaks caused by cracked, split, or brittle hose sections
• Restores proper routing when the original hose is kinked, collapsed, or damaged
• Compatible with factory routing and mounting points for correct fit

• Disconnect power and water supply before starting any repair
• Inspect adjoining clamps and fittings; replace if corroded or damaged
• Follow OEM routing and secure with the original clamps or new OEM-style clamps

These replacement 6" FXF vacuum bags capture dust and debris to restore pickup performance and keep the appliance's airflow and motor compartment cleaner. Designed as a direct-fit consumable for compatible bagged upright and canister vacuums. What it does:

• Collects dirt, dust and debris so particles stay contained for easier disposal
• Helps maintain suction by keeping the vacuum's intake and motor chamber clearer
• Reduces dust and allergen re-distribution compared with a torn or overloaded bag
• Replaces worn or full bags that cause reduced capacity, visible dust escaping, or increased odor

• Always unplug the vacuum before removing or installing bags
• Remove the full bag carefully to avoid spilling debris; seal and dispose per local regulations
• Verify correct orientation and secure fit before operating to avoid leaks
• Replace bags regularly; inspect the inlet collar and seals for wear when servicing

This drain tube routes wastewater from the appliance to the drain system, restoring proper drainage and preventing leaks or pooling. It's a direct-fit replacement designed to match the original drain path and connections. What it does

• Carries wastewater from the appliance pump to the household drain or disposal.
• Helps stop leaks or puddling caused by cracked, kinked, or clogged tubing.
• Restores normal drain cycles when a damaged tube prevents water removal.
• Prevents backflow when installed with proper routing and clamps.

• Disconnect power and turn off the water supply before starting any repair.
• Verify the tube routing and clamp positions match the original to avoid kinks and siphoning.
• Use proper clamps or fittings; tighten securely but avoid over-tightening which can damage the tube.

This replacement drain tube directs discharged water from the appliance to the household drain, helping restore proper drainage and reduce the risk of leaks. Designed to match OEM fit and routing for straightforward replacement. What it does:

• Channels drained water away from the appliance to prevent pooling and leaks
• Replaces cracked, split, or collapsed tubing that causes slow or no drainage
• Restores proper flow when water backs up or drains intermittently
• Works with factory clamps and fittings to maintain a secure seal

• Disconnect power and shut off water supply before beginning service
• Inspect surrounding fittings and clamps; replace any damaged hardware for a reliable seal
• Follow the appliance service manual for correct routing and clamp locations
• If you smell gas or detect significant water damage, stop.